Library Hutch for Grace's Town

Primary tabs

Library Hutch for Grace's Town

The hutch will finish this project out and, your kid's will love to play endlessly for hours be it a library to a convenience store.

HANDMADE FROM THIS PLAN >>

Projects built from this plan. Thank you for submitting brag posts, it's appreciated by all!

As promised, here is the first of the "Grace's Town" Collection of plans.  Your child is about to have what you cannot buy - a plan designed by me specifically for the little imaginations of preschoolers!  These plans are designed for Mom's to build, and Mom's to customize for their child.  I just know you will enjoy building this and gifting this collection, every bit as much as your child will enjoy playing with it.

I added doors to this plan so your child can close up shop.  Of course, you can leave the doors out, or paint them in chalkboard paint for your little one's to write on.

So let's get too it!  See the plan after the jump (click on READ MORE below).


This plan if for a hutch that can be used on any of the pretend buildings that are 2 feet wide.  It measures 24" wide x 24" tall and 8" deep.  It is designed for a preschooler.

Shopping List: 

1- 1 x 3 x 8'
1- 1 x 2 x 8'
1- 1 x 8 x 8'
1- 1 x 6 x 8'

1 1/4 inch screws
2 inch screws
1 1/4 inch finish nails
2 inch finish nails
wood glue
wood filler
120 grit sandpaper
primer
wood conditioner
paint
paint brush
Tools: 
measuring tape
square
pencil
hammer
safety glasses
hearing protection
drill
circular saw
nailer
sander
This plan if for a hutch that can be used on any of the pretend buildings that are 2 feet wide. It measures 24″ wide x 24″ tall and 8″ deep. It is designed for a preschooler.
Cut List: 

Cut list for the doors on the hutch
2 – 1×10 @ 17 1/2″ (Optional Doors)

Cut list for the 2 foot wide hutch

3 - 1×8 @ 24″ (Sides and Top of the Hutch)
2 – 1×2 @ 7 1/2″ (Supports for the Hutch to Secure to Base Cabinet)
1 – 1×6 @ 24″ (Header)
1 – 1×2 @ 24″ (Above the Header Trim)
1 – 1×3 @ 24″ (Top of the Cabinet Trim)
2 – 1×3 @ 17 3/4″ (Front Hutch Trim)
1 – 1×2 @ 24″ (Back Support)

Step 1: 

Start will all the boards A. Use 1 of the boards A and nail through the top of A into the end edges of A, to make a three sided box, as shown above. The overall measurements will be 24″ wide and 24 3/4″ tall. Use glue and 2″ nails.

Step 2 Instructions: 

Now add the supports, B, as shown above. Nail through the bottom end of A into the side edge of B, as shown above. You will use B to secure the hutch to the base cabinet. Use 2″ nails and glue.

Step 3 Instructions: 

Add the header, C, measuring down 1 1/2″ from the top, as shown in the diagram above. Use 2″ nails and glue.

Step 4 Instructions: 

Now add the above the header trim piece, D, as shown above. Use the 2″ nails and glue to nail the trim piece into the header, C, and the sides of the hutch, A.

Step 5 Instructions: 

Add piece, E, as shown above, nailing into piece D and using glue and 2″ nails.

Step 6 Instructions: 

Add pieces F to the sides of the hutch as shown above. Nail F into the sides, A, and into the supports, B, and toenail into the header, C.

Step 7 Instructions: 

Attach the back support, G, as shown above, using 2″ nails and glue.

Step 8 Instructions: 

Attach the back support, G, as shown above, using 2″ nails and glue.

Step 9 Instructions: 

Secure the hutch to the base cabinet by screwing through the supports, B, into the top of the base cabinet with 1 1/2″ screws.
10. Fit the doors and attach with hinges. Remember, doors create a pinch hazard for small children, and these doors will fit snug. Omit the doors if you are concerned about little fingers being pinched.

Estimated Cost: 
Skill Level: 
Style: 

Comments

For those of you with very small children and want the doors, but are worried about the pinch hazard - change the Front Hutch Trim pieces, F, from 1x3s to 1x2s. Also, cut the doors at 16 1/2" instead of 17 1/2" . This will give 1/2" extra space around each door when it is closed. When you attach the doors, leave a 1/2" gap around all sides. The cabinet will not look as nice with the 1/2" gap around the doors, but you will not have to worry about little fingers being pinched.

Love your blog! We are planning to build the play kitchen for my daughter's birthday. Will you be including any plans for a "grocery store" for Grace's Town? Thanks for the inspiration, and for helping SAH moms save money on all of the "things" we want our families to have, but can't afford to buy! Let's BUILD them!

Thank you so much for these plans! We could have never afforded (or found) such a cute library for our daughter. You are truly amazing! I was wondering if the pieces F, for the front trim are supposed to be 1x3s? Our 1x2s don't cover the supports like your picture shows. It still looks great though! Thank you again!

You can use either 1x3 or 1x2s for the hutch side trim. On the library I made my niece, I placed the supports vertical and used a 1x2. The picture shows a 1x3, so I will change the plans. Thanks for letting me know!