Large Rustic X Bench

Primary tabs

PDF versionPDF version

Additional Photos

Keywords: 
make a bench, make bench, build bench, pottery barn bench, pottery barn rustic bench
Dimensions: 
54" Wide x 18" Tall x 12" Deep
Dimensions: 
  • 3 – 1×3 8′ boards 
  • 1 – 1×2 8′ board 
  • 1 – 1×12, at least 54″ long
Common Materials: 
1 1/4 inch screws
2 inch screws
wood glue
wood filler
120 grit sandpaper
primer
paint
paint brush
Tools: 
measuring tape
square
pencil
drill
jigsaw
compound miter saw
sander
Cut List: 
  • A) 4 – 1×3 @ 17 1/4″ (Leg Pieces, notch out in step 1) 
  • B) 4 – 1×3 @ 11 1/2″ (End Aprons and Side Stretchers) 
  • C) 4 – 1×2 @ 17 1/4″ (Leg Pieces to complete the legs) 
  • D) 3 – 1×3 @ 45″ (Aprons and stretcher) 
  • E) 2 – 1×3 @ 25 3/4″ (Cross Supports) 
  • F) 1- 1×12 @ 54″ (Top)
Project Type: 
Skill Level: 
Estimated Cost: 
Style: 
General Instructions: 

Work on a clean level surface. Use good boards. Cut all of your boards first. Check for square after each step. Because this is a bench, I recommend using screws instead of nails. Always use glue. Predrill and countersink your screw heads. Have fun and be safe.

Step 1

Notch out the Legs. Mark the 1×3 parts of the legs as shown above. With a jigsaw, cut out as shown above.

Step 2

Attach the End Aprons/Stretcher. Attatch the end aprons, B, to the 1×3 legs pieces, A, as shown above.

Summary: 

A simple bench gets stylish with some clever cross bracing and false notching. See why so many have built this bench already!

Special thanks to our readers for sharing their photos. Also note, smaller Rustic X bench plans are also available.

Step 3

Complete the Legs. Fasten C, the 1×2 part of the legs, to the rest of the leg. Keep the outside corner flush.

Step 4

Cut the Cross Supports. Cut the cross supports as directed above. Use your square to determine the cuts and mark on the board prior to any cutting. The overall length, from the longest point to the longest point is 25 3/4″.
This is by far the trickiest step. What you will need to do on the end cut at two different angles, is first mark out the 60 degree angle from the top corner (when imagining the board in place on the bench). Also mark and cut the bottom angle. Then cut these angles and fit on the bench. Center the bottom on the stretcher. Then mark off where the top overhangs the top of the bench and clip off. This cut does not have to be perfect – you will just need to make sure it sits lower than the top of the bench.

Step 5

Aprons and Stretcher. Fasten the aprons and stretcher in place as shown above. You will need to use 1 1/4″ fasteners to fasten the aprons to the inside of the 1×3 leg pieces. Center the stretcher on the side stretcher, as shown above and fasten in place.

Step 6

aprons are not shown in the above diagram
6. Fasten the Cross Supports. Fasten the cross supports as shown above.

Step 7

Top. Fasten the bench to the top, as shown here. If you wish to hide your screw holes, you will need to either predrill through the apron and screw into the underside of the bench or you can purchase small L brackets and fasten the top in place. If you are painting, you can simply predrill and scew through the top into the aprons.

Step 8

Comments

I just found your site and I just wanted to say THANK YOU! My to do list just grew and I can't wait to try out some of these projects. Thank you for your generosity in sharing your talent!

I'm so inspired by you. My husband and i recently moved into our first home andwe need a ton of furniture on a 'new home owner' budget. awe have been looking all over town for furniture I like that we can afford, and needless to say after 3 months of looking I still am using Yaffa blocks as nightstands. I love your furniture and you make it look so possible. My new goal is to pick one of your peices to start with!
Thanks.

Wow, just found your site and have become a follower. I can't wait to do some browsing. I love furniture and anything related and can spend hours looking through magazines or walking through furniture stores. Come visit with me when you have a chance.

I just came across your site last night and I must say, I am SOO excited! We are doing some MAJOR remodeling on our home right now and I, like you am a stay at home mom with expensive taste, but a very frugal lifestyle. Thank you, I may just be able to get my home to look the way I've always wanted with your help!!

Yay! I am loving your site so, SO much! I actually have this bench and use it a ton... I would love to make one as well. Thanks so much for this, I'll be linking.

Oh goodie goodie goodie! I love your blog!! I'm making dollhouse miniature furniture and I LOVE this bench! Your plans could be done in 1 inch equals 1 foot. PERFECT for a dollhouse! :D
Thank you so much! I'm following!
Kathi

You are amazing. Yet again you design beautiful furniture. I am asking for a nail gun for my Valentines, Mothers Day, Birthday, Anniversary gift :). Thanks Ana!

I gasped out loud when I saw this bench! I have been looking for a bench for a long, long time, but refuse to pay a lot of money for one. Thank you, thank you!

I just found your site and LOVE it! I want to make so many of your projects. Your site has given me the inspiration to believe that I CAN build it! My husband and I picked a simple plan to start with - the Hyde Side Table.

LOVE this bench....would love to see it in a console table height as well. Something for behind the couch, it is FABULOUS!!! Thanks so much for your inspiration!

I just built this today and I did it all by myself!!! I'm soooo proud!
I did find out though that you need more 1x3 boards than you have listed for materials and thought I would let you know. The 3 1x3's added up equals 288 inches. and if you add up the measurements of what you need cut it comes to 288.68 and that's without taking in to consideration that you will lose some length with each cut made.
I can't wait to paint it. And I will post a picture and a link when I'm done.
thank you for all you do and I am looking forward to building MORE!!!!

Hi! Love your blog! I just started working on this project today and have a question. My table is small, and I only have about 40 inches between the legs. So, I had my 1x12 cut only to 36" so that it would fit nicely under the table between the legs when not in use.

Now I am having trouble calculating the aprons/stretcher/cross supports. Help! To be precise, my bench top is 36 1/4" long. How do I calculate the size of the other parts? (I'm assuming my legs can remain the same)

I am the girl that took all the boy classes in High School and College. I majored in Construction management with a specialty in furniture building. I love that you have this blog. My sister call me a couple of days ago and told me about it. I especially love that you are helping people realize that you do not need a degree to do stuff like this. Basic furniture really is basic. Rock on!

I am getting ready to build 2 of these benches this week. Your instructions say that it is 6 " shorter than the pottery barn bench. Just wondering if the large unfinished bench and black bench are the same as your plans? The bench in the You tube video looks a lot smaller.

I also built this bench (with the help of my dad's tools) yesterday. My 1x12 (unfortunately) was only 11.25" wide, as as a result, my base piece is sticking out beyond my top...however, we are taking a hand saw and whacking them off (or going to a different store to buy a different 1x12 that's wider!) Has anyone heard of a 1x12 being 3/4" narrower than the measure? I have definitely heard of them being 1/4" narrower, but 3/4"?!

Also, I needed 4 1x3's as well, as a previous poster mentioned. AND, we didn't use a jig saw, we notched the legs with a mitre saw and chisel for an more exact cut.

Hi, I am working on the rustic bench. I decided I was going to make it taller and turn it in to a table basically. I kept it 54" long but I made my legs 30". I got stumped when I came to cutting the angles for my cross support and saw your post and figured you may have figured it out! Please help!!!

Thank you sooooo much! I found your site a few weeks ago. A friend mentioned you on facebook and I had to investigate. Finally this past weekend, my dear sweet husband was patient enough to show me how to use his saw, and power tools. He didn't even cringe when I used them wrong. So we made this bench and had a blast doing it. In fact all three of our boys played a part in building it too. I have shared your site with all my friends and can't wait to build more.
Ana you ROCK, and really I can't thank you enough!

the amount of wood you that is on the shopping list isn't enough to make all the cuts that are needed and you might want to add fasteners to the shopping list as well because they are needed in step 3. disappointed

My hubby and I are going to attempt to make two of these starting this weekend. I was going to start cutting however I am having a hard time seeing the measurements on all of the drawings. I enlarged them but they just get distorted and fuzzy. Can anybody help me with this? I don't want to mess it up. We have to finish them this week as they are for a fundraiser next weekend.

I want to make this bench in an 84" length. do you think it's needs support in the middle?

Are the cross supports a structural element or are they more for design? I want to make benches for your "Rustic Table", and these (without the cross supports) most closely match it. Thanks!

CassieT

Hi There,

For the legs, do you make them look like one piece of stock by using wood filler? To fill any small gaps between the 1x2 and 1x3?

I can't quite tell if the bench is sanded to soften the corners for the top, legs and other pieces.

Any feedback would be great. I will start this soon.

Pages

HANDMADE FROM THIS PLAN >>

Projects built from this plan. Thank you for submitting brag posts, it's appreciated by all!

Pages