Dorm Desk

Primary tabs

Dorm Desk

Bar height dorm desk designed to be used with bar stools. Adds modern storage, a base support, and is easy to assemble/disassemble.

HANDMADE FROM THIS PLAN >>

Projects built from this plan. Thank you for submitting brag posts, it's appreciated by all!

Thank you all for understanding and giving me what feels like a vacation yesterday!  It's been more like a building break (not a break from building, rather a break to build  :)  ), but I wouldn't have it any other way.

Do you find when you've got too much on your plate, when you've got too many goals going on at the same time, that maybe everything doesn't get the love and attention it should?  I was feeling that way yesterday as I was drawing up a plan, and having trouble being passionate about the design.  I know I've got a good design, and one I can be proud of, when it's all I can do to restrain myself from building it myself.  The buildies.  And if a design isn't giving me the buildies, well, maybe that is a plan that I shouldn't post.

Well, this desk, table, whatever you want to call it, but I'm calling it the dorm desk, it's giving me some serious buildies.

I tend to be a storage junkie, with a dream of a bare house.  No stuff visible anywhere.  Everything has a place.  And the dorm desk that I designed does just that, stores stuff, but is practical and compact.  It's also bar height, so some cool stainless stools would look amazing under it.  And here's another secret for those of you who read my ramblings: cheap tin flashing is magnetic.  Cut it with tin snips and glue it in the space shown above for a magnet board.  It's available in rolls at most any hardware store.

I choose to keep the storage open so that the desk could be placed against a wall or cords run through.  Also, the stretcher on the bottom will help keep the legs from spreading and stripping screws.

And yes, for those of you (I'm both happy and sad for you) with their babies taking their station wagons to college, I did design the dorm desk so that you can break it down into manageable pieces. 

Shopping List: 

1 - 1x8 @ 12 feet long
1 - 1x12 @ 8 feet long
2 - 1x2 @ 8 feet long
3 - 2x2 @ 8 feet long
1 - 24" x 36" Pine Project panel or 1/4 sheet of plywood

2 inch screws
1 1/4 inch finish nails
2 inch finish nails
wood glue
wood filler
120 grit sandpaper
primer
wood conditioner
paint
paint brush
Tools: 
measuring tape
square
pencil
safety glasses
hearing protection
drill
circular saw
nailer
sander
level
countersink drill bit
General Instructions: 

Please see PDF for full instructions.

Dimensions: 
24" x 36" x 42" Tall
Cut List: 

Please see PDF for cutting list.

Step 1: 

First we simply screw the shelves to the sides. The sides and shelves are 1x8s. I’ve been using my Kreg Jig™ for most of my joints lately and am in love. But if you don’t have a Kreg Jig™, you can countersink and screw from the outside. Unless of course, you are planning on storing gold on those shelves. But then again, if you had that much gold, you could afford a Kreg Jig™ LOL

Step 2 Instructions: 

Now these are 1x12s. Glue is what holds everything together with unfinished wood. So apply glue and then use finish nails to nail the sides to the shelves. I personally like to mark all the shelves before I do any fastening. It just makes everything go so much smoother when it’s time to build.

Step 3 Instructions: 

This little guy is just for looks.

Step 4 Instructions: 

These are for looks, but they will also give you a good spot to start and stop your tin flashing or corkboard.

Step 5 Instructions: 

pretty again

Step 6 Instructions: 

These are for looks. Don’t forget glue. Yay! The shelf part is all done! That wasn’t so bad, was it?

Step 7 Instructions: 

Now this is super easy. Take the 24″ x 48″ Pine Project Panel (I like to use project panels because they are smooth and the edges are finished and they are durable) and glue and screw the side aprons on. Super easy.

Step 8 Instructions: 

I know you can build a square. Just make sure you check for square. Oh, a little tip from someone not so wise, maybe elevate the bottom blue board up just a hair. Sometimes floors aren’t completely level, and if you have just the two posts flush on the ground, you will decrease your chances the tabletop will “rock”. Or you could ad cork pads under the legs.

Step 9 Instructions: 

And it’s super easy to assemble. Just screw the four different pieces together!

Project Type: 
Room: 
Skill Level: 
Style: 

Comments

Hey Ana, Do you have any plans for the crafters out there who have tons of 8 1/2 x 11 and 12 x 12 scrapbook paper and need a place to store it where it is easy to see? My scrapbook paper runneth over!

Good news: the PDF opened just fine for me :-) Bad news: The project panel listed and the measurements for the aprons and stretcher don't match up. Is the project panel supposed to be 24" X 48"?

I am so very excited to build this desk for my 13 year old son. I am actually recruiting him to help with this. I think he will develop a sense of pride in making something of his very own. We are starting this tomorrow and hope to have a pic after the weekend! Wish me luck!

We did it!! I think my son has met his first true love!! This DESK! We were able to get this put together on Saturday afternoon. It seems a bit tall for a 13 year old, but he is already 6' tall, so we won't have to worry about him outgrowing it, slouching over a short desk, or hitting his knees. As soon as that top was secured with the last screw, he didn't waste any time. He had his lamp, stapler and model car kits ready to stock the shelves! Will post a photo once we complete the finishing steps. Thank you Ana!

I love this desk it's so simple and I want to build a couple for my grandchildren. I don't quite understand why it's so tall? 41 1/4" legs are going to put this desk up there pretty high.The computer desk I'm setting at to type this message with, is only 29" high. From the floor to the very top. I can't imagine the chairs I must need for this? is there a shorter version of this desk?

The cut list says to get a 24" x 36" pine panel. This should be a 24" x 48" based on the measurements of the desk itself and the remaining cut directions. Just getting ready to build two of these. These are exactly what I needed.