Hello! I’m Ana, a mother and homemaker from Alaska.
Skeching
100’s of FREE plans!!
You can make ANYTHING!
stick
img
sticks
img

Pub/Counter Height Table (Seats 6)

March 21, 2011 |
posted by biz_kid1
PDF versionPDF version

Pub/Counter Height Table (Seats 6)...a slightly smaller version of the Seats 8 square table!

Pub/Counter Height Table (Seats 6)

Handmade from this plan >>

Projects built from this plan. Thank you for submitting brag posts, it's appreciated by all!

Dimensions

Dimensions: 
Pub/Counter Height Table (Seats 6)
Dimensions: 
59 1/2" x 45 1/2" x 36"

Materials and Tools

Shopping List: 
2 4x4 @ 8'
9 1x4 @ 12'
1 1/2 inch screws
2 inch screws
wood glue
wood filler
120 grit sandpaper
primer
wood conditioner
paint
paint brush
Tools: 
drill

Cut List

Cut List: 

Cutting Instructions: 
4 4x4 @ 35 1/4" (Legs) 2 1x4 @ 59 1/2" (Aprons) 4 1x4 @ 44" (Aprons & Underside Supports) 13 1x4 @ 59 1/2" (Table Top) 12 1x4 @ 12" (with 45-degree cuts on ends NOT parallel to each other) (Underside Corner Supports)

General Instructions

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!

Step 1

Pub/Counter Height Table (Seats 6)

Connect one 59 1/2" Apron square with one 58" Apron perpendicular at the ends (forming a L-shape) using 1 1/2" screws and glue. Repeat for other 59 1/2" Apron and one more 58" Apron. Attach both L-shaped pieces to form a square using 1 1/2" screws and glue.

Step 2

Pub/Counter Height Table (Seats 6)

Attach Leg to Apron on the two sides that both touch using 2" screws and glue. Repeat for each Leg.

Step 3

Pub/Counter Height Table (Seats 6)

On the 59 1/2" Aprons, mark 18" in on each side; attach 58" Support using 2" screws and glue. Repeat with other 58" Support.

Step 4

Pub/Counter Height Table (Seats 6)

Attach one 59 1/2" Table Top board perpendiculer to the 58" Aprons and Support boards and square to the edge of the apron using 1 1/2" screws and glue. Use one or two additional 1 1/2" screws on EACH Support board, screwing in from the Table Top through to the Support board (for a total of 6-8 screws for each Table Top board). Repeat for remaining 16 Table Top boards.

(Not pictured) Cut a 45-degree angle on the ends of the 12" 1x4 Support boards. Attach to underside in corners of table using 1 1/2" screws from the apron into the Support board. Repeat for all remaining Support boards.

Finishing Instructions

Preparation Instructions: 
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.

Comment viewing options

Select your preferred way to display the comments and click "Save settings" to activate your changes.
clips

PUB TABLE WITH STORAGE

I REALLY want to build this table - But I have my heart set on something with some "storage" under - You know just to keep a table caddy (salt pepper / oil vengar / that type of thing)- I have seen many while shopping around like this with storage underneath - although as you can imagine - they are VERY expensive - So I was wondering what your thoughts would be on adding just another (top) just say two feet below the actual top? Do you think the functionality would be there? Also - if yes - Do you think the easiest way to accomplish that would be to duplicate the directions for the top at whatever level I decide below

posted by TTWEEDY | on Tue, 2012-09-25 11:01
clips
biz_kid1's picture

You'd have to consider the height of your chairs/stools...

...as adding the extra level of storage sounds like it might infringe on leg space. If you don't need much storage, maybe consider adding a hanging "shelf and stick a wire basket on it underneath the center of the table top (basket like this: http://i.ebayimg.com/t/York-Under-Shelf-Pantry-Wire-Storage-Basket-Kitchen-Organizer-/00/s/Mjc1WDMwMA==/$(KGrHqN,!ksE-oOD1Z((BPzo(wF(q!~~60_35.JPG).

posted by biz_kid1 | on Tue, 2012-09-25 13:10

pub/counter height table

I see on cut list 12 1x4's at 12" each for corner support, but don't see what to do with them. Help. thank you.

posted by Lisa B (not verified) | on Thu, 2012-11-29 09:11
clips
biz_kid1's picture

It's in Step #4...

"(Not pictured) Cut a 45-degree angle on the ends of the 12" 1x4 Support boards. Attach to underside in corners of table using 1 1/2" screws from the apron into the Support board. Repeat for all remaining Support boards." because my Google Sketchup drawing skills didn't know how to draw angled boards! You just cut angles on them so they'll fit in the corners...hope that helps!

posted by biz_kid1 | on Thu, 2012-11-29 09:29

Modified Cuts

I love this table and I have some questions, though - I'm horrible at measurements so would it be possible to get the cut measurements for a perfectly square table that seats 4? Also - would this table be able to handle the weight of a granite/marble/ or slab of stained concrete on top? Thank you!

posted by AGarcia (not verified) | on Wed, 2012-12-05 01:52

Comment viewing options

Select your preferred way to display the comments and click "Save settings" to activate your changes.

Recent comments

Social

Let's Connect

Tweets

  •  

User login

Not Much >>

What's going on up here in Alaska.

Momplex Cam >>

Momplex Cam >>

We are DIYing our moms a Duplex in Alaska! Check out our progress so far as we owner build a home, step by step. Read the Momplex blog here.

Special Thanks

The free content provicded by this website is made possible by the following current sponsors.  Thank you!


   

Momplex Vanilla Kitchen Plans and How-Tos


Check out how we DIYed a full kitchen here!

Momplex
Momplex
Momplex
Project Plan
Momplex
Project Plan
Project Plan
Momplex
Project Plan
Project Plan
Project Plan
Momplex
Momplex
Project Plan
Project Plan
Momplex
Project Plan
Project Plan
Momplex
Momplex
Momplex
Momplex
Project Plan
Momplex
Video
Momplex
Momplex
Momplex
Project Plan
Momplex
Momplex
Project Plan
Momplex
Momplex
Project Plan
Project Plan

Handmade Holiday Gift Plan Tutorials

Project Plan
Project Plan
Project Plan
Project Plan
Project Plan
Project Plan
Project Plan
Project Plan
Project Plan
Project Plan
Project Plan
Project Plan