Hailey Hutch for Twin and Full Beds

Primary tabs

Help us get rid of spam!

Hey there!  Ana here.  If you got a second and see a comment that you suspect is spam, please click the "This Comment is Spam" text at the bottom of the comment.  Sure appreciate the help! 

Hailey Hutch for Twin and Full Beds

The hutch for the Hailey Storage Bed Collection.  Plans show both full and twin sizes.  Please note that this hutch is designed for a very tight fit around the bed, and you should measure your headboard and bed width before building to ensure enough space around the bed.

HANDMADE FROM THIS PLAN >>

Projects built from this plan. Thank you for submitting brag posts, it's appreciated by all!

Author Notes: 

We couldn't be more pleased with Grace's Hailey Bed

But we have decided not to do the towers and hutch because of the room size - but I sure am looking forward to seeing someone else add towers and a hutch over their Hailey Bed.  Please, give a shout if you would like to see more plans in this collection.
Shopping List: 

2 - 1x12 @ 8 feet long

1 - sheet 1/4" plywood, hardboard, beadboard or other backing material
2 - 1x2 @ 8 feet long
1 - 1x3 @ 8 feet long
1 1/4 inch screws
1 1/4 inch finish nails
2 inch finish nails
wood glue
wood filler
120 grit sandpaper
primer
wood conditioner
paint
paint brush
Tools: 
measuring tape
square
pencil
safety glasses
hearing protection
circular saw
nailer
sander
level
countersink drill bit
General Instructions: 

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!

Dimensions: 
Dimensions are shown above for a full size. Twin dimensions are shown in plan.
Cut List: 

Full Size Cut List

2 - 1x12 @ 54 3/4"
7 - 1x12 @ 10 1/2"
1 - 1/4" plywood @ 54 3/4" x 12"
2 - 1x2 @ 54 3/4"
2 - 1x2 @ 9 3/4"
1 - 1x3 @ 54 3/4"
Twin Size Cut List
2 - 1x12 @ 39 1/4"
5 - 1x12 @ 10 1/2"
1 - 1/4" Plywood @ 39 1/4" x 12"
2 - 1x2 @ 39 1/4"
2 - 1x2 @ 9 3/4"
1 - 1x3 @ 54 3/4"
Step 1: 

As with most storage, start by building a simple box. As this is fully framed with plywood on the back, if you have a nailer handy, go ahead and nail this one (with glue of course and 2" finish nails). You can also use screws. Adjust for square.

Step 2 Instructions: 

Now add the plywood back with 1 1/4" finish nails and glue.

Step 3 Instructions: 

Trim the front out as shown above with 1 1/4" finish nails and glue.

Step 4 Instructions: 

And now the sides.

Step 5 Instructions: 

Finally, a little piece of crown will help the hutch tie in with the towers and match the headboard plans.

Step 6 Instructions: 

If you are building a twin size, here are the dimensions. Make sure you measure your bed - as this is a very tight fit.

Preparation Instructions: 
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
Project Type: 
Estimated Cost: 
Skill Level: 
Style: 

Comments

are there dimensiona available for a queen bed

Is there a way I could get these plans in a queen size? Also, can I get the plans for the towers as well? Or possibly the whole bed?