Bench Seats for Child Surf Board Outdoor Table
May 13, 2011 |
1 Comments
posted by Ana White
PDF versionBench seats for little ones to take to the beach. Works with the Surf Table.
Handmade from this plan >>
Projects built from this plan. Thank you for submitting brag posts, it's appreciated by all!
Dimensions
Dimensions:
Dimensions:
Dimensions are shown above. Materials and Tools
Shopping List:
1 - 2x2 @ 4 feet long
1 - 1x3 @ 8 feet long
2 1/2 inch screws
2 inch finish nails
1 1/4 inch pocket hole screws
wood glue
wood filler
120 grit sandpaper
primer
wood conditioner
paint
paint brush
Tools:
measuring tape
square
pencil
safety glasses
hearing protection
drill
compound miter saw
nailer
sander
countersink drill bit
Cut List
Cut List:
4 - 2x2 @ 9 3/4" (Ends cut at five degrees off square with a five degree bevel, ends parallel to each other)
4 - 1x3 @ 6 1/2" (Aprons - both ends cut at 5 degrees off square, NOT parallel to each other)
4 - 1x3 @ 10 3/4" (Seat Boards)
General Instructions
Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!
Step 1
Mark the inside corners of the legs.
Step 2
Attach aprons to legs as shown above. You can use either the Kreg Jig or just screws and glue.
Step 3
Start in the center and work your way out, attaching seat boards as shown above.
Step 4
Optionally, you can add supports like done above, but it's not necessary for support.
Finishing Instructions
Preparation Instructions:
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth.
It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
May I Suggest a Finish?
- 1 of 8
- ››
- ‹ previous
- 409 of 811
- next ›
Printer-friendly version
Send by emailtablica
[url=http://www-tablica.pl]tablica[/url] tablica ogloszenia tresc temat ogloszen fajna strona
posted by ToppyFeahFeawre (not verified) | on Wed, 2012-05-16 17:41
Recent comments
- I really like this website , 2 sec ago
- I hate taping and mud! 1 hour 8 min ago
- It’s hard to find excellent 1 hour 21 min ago
- I don't know what to say. 1 hour 21 min ago
- This valuable editorial was 1 hour 25 min ago
- How long have you been in 1 hour 25 min ago
- I am fond of your blog. It 1 hour 26 min ago
- I totally agree the 1 hour 27 min ago
- Please keep on posting such 1 hour 28 min ago
- The blog is really 1 hour 30 min ago
Search
Let's Connect
User login
Not Much >>
Momplex Cam >>
Momplex Cam >>
We are DIYing our moms a Duplex in Alaska! Check out our progress so far as we owner build a home, step by step. Read the Momplex blog here.
- 1 of 20
- ››
Most Viewed Plans
New here? Check out our most popular free, step by step furniture plans.
Active forum topics
- PB Ashby Dresser
- To Paint or Not to Paint....
- SketchUp and Cut List Plug-In
- Female-friendly power tools or tools for small hands
- A really silly beginner question
- Aussie timber (lumber) sizes - 1 x 2 available in Australia???
- Farmhouse Table with x-legs
- OUTDOOR WOODEN SWING SET
- Electric sprayer - worth trying?
- Finishing Suggestions for Apothecary Console
I'm on Instagram!
