Round Outdoor Adirondack Side Table

Primary tabs

Round Outdoor Adirondack Side Table

Round Adirondack table for outdoor use. Ideal for resting between Adirondack Chairs or on it's own. Inspired by polywood furniture and llbean furniture. Create the DIY version for an affordable option!

HANDMADE FROM THIS PLAN >>

Projects built from this plan. Thank you for submitting brag posts, it's appreciated by all!

Author Notes: 

We're back, we're home, we missed you!

Wanted to first and foremost extend a thank you to all of our readers - especially those that take time to help others out and answer questions, and those that post to our brag board - you don't know how much your time helps!

As any blogger will tell you, when you blog about something you love, it tends to consume your life. Finding that balance between family, friends, and doing something that is not productive in any sense, has been a great challenge for me. I tell you, it's not uncommon for me to wake up in the middle of the night and start drawing designs, or sneak out to the garage when Grandma starts reading Grace a book. I'll be the first to admit I'm a tad obsessed with DIY furniture.

So I'm positively bragging when I say we enjoyed our trip to Maui last week to the point of blistering sunburns. As reluctant as I was to go, and leave my beloved saw behind, I'm humbled to say, I needed the break. But I'm also so happy to be back!

I want to add a few more plans for outdoor furniture, things like occasional tables, storage, some planters, benches, and a hanging swing. I know we've been doing a ton of outdoor projects of late, and I like to keep things varied, but I just can't help myself, I'm so excited that summer is finally here! So bear with me, I promise, we'll be doing lots more interior projects before too long. LOTS more :)

Source: cdni.llbean.com via Ana on Pinterest


Todays plan is inspired by my Pinterest Board. Have you been to Pinterest? It's so so inspiring! Oh, the things we are going to build!

Shopping List: 

2 - 1x4 Boards, 10 feet long (cedar or other weather resistant species recommended)
3 - 1x2 Boards, 8 feet long (cedar or other weather resistant species recommended)
Use galvanized hardware. Instead of screws, bolts may be used, enabling the table to disassemble for winter storage.

1 1/4 inch screws
2 inch screws
wood glue
wood filler
120 grit sandpaper
primer
wood conditioner
paint
paint brush
Tools: 
measuring tape
square
pencil
safety glasses
hearing protection
drill
jigsaw
compound miter saw
sander
level
countersink drill bit
General Instructions: 

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!

Dimensions: 
Cut List: 

2 - 1x4 @ 31 1/2"
2 - 1x4 @ 30 7/16"
2 - 1x4 @ 27 1/16"
2 - 1x4 @ 20"
2 - 1x2 @ 29 3/4"
2 - 1x2 @ 23 1/2"
2 - 1x2 @ 3 1/2"
4 - 1x2 @ 30" (Both ends cut at 45 degrees off square, parallel ends)
2 - 1x2 @ 17 1/2"

Step 1: 

Start in the center and attach the tabletop supports to the underside of tabletop with 1 1/4" screws and glue. Use the diagram above to help you find the centers of the supports and tabletop boards. Then work you way outwards, leaving a 1/2" gap between tabletop boards.

When all boards are screw to supports, use a string held in the center of the table and to a pencil to draw circle shape as shown above. Cut out circle shape with jigsaw. Sand edges until smooth and even.

Step 2 Instructions: 

Lay the legs supports on the underside of the table as shown above. Use 2" screws and glue to attach supports to underside of table. Round corners to give the table a softer look as shown in diagram.

Step 3 Instructions: 

Round corners of spacers and attach to legs supports as shown above. Use 1 1/4" fasteners and glue.

Step 4 Instructions: 

Attach legs to the tabletop as shown above. Use 1 1/4" screws and glue.

Step 5 Instructions: 

Attach remaining legs to spacers as shown above.

Place table upright and adjust for level by resting a level on the tabletop. When the table is level, screw the two legs together as shown above.

Step 6 Instructions: 

Supports - attach base supports as shown above.

Preparation Instructions: 
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. 
 
 It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
Project Type: 
Estimated Cost: 
Room: 
Skill Level: 
Style: 

Comments

Anna, WONDERFUL SITE!!!!
i've just found you, I'm just finishing the outdoor bench, thank you so much. Any shot of a BBQ helper, something that can store all the tongs, etc, with a top to prepare, i was looking at the red cart. As soon as my hubby saw that i was interested in building, he went right out and got my the master kreg tool....and requested a BBQ cart.
thanks so much for your time, it is much appreciated,
angie
southern Ca

Thanks so much for sharing this. My husband made me adirondack chairs many years ago. I love them, but I have been bugging him to make a table to go with them. thanks to you, now maybe he will make one for me.

Um is it just me or does the .pdf not work?? Love this, am think of making an Adirondack set for mum for xmas :) I think she would love sitting out in the garden on these. Love it!

I just went out and got a couple pallets to use for this project. We just moved and I don't have half my tools, but I will make it work! This is going on the porch at the new house, photos will follow of course!