Full Toy box bookcase

Difficulty
Beginner Projects
| Print this plan

I got the idea from the Bankable Bookcase plans on this site, but modified it to closer resemble the closed top version that I found on the Land of Nod website. I think the resemblence is good, and at a fraction of the price. This is my first plan using Google Sketchup...they should get better...I added trim all the way around the top and the bottom of mine, if you follow the plans, the trim will only be on the front and you will be able to bank multiple cases together, if you trim out the sides of the top and bottom, they are better suited as stand-alone book cases.

31"W x 15 1/2"D x 60 3/4H (including trim)

Preparation

Shopping List

1 Sheet 4x8 Hardwood Plywood (I used Lowe's Blondewood)
1 8ft. 1x2
11ft. 2 3/4" trim (I used Colonial)
8ft. 1 3/4" trim (I used Colonial)
Hardwood edge banding (if you want to stain)

Common Materials
1 1/4 inch finish nails
120 grit sandpaper
wood conditioner
paint brush
Cut List

2- 15" x 60" plywood (sides)
4- 14" x 28" plywwod (shelves/bottom)
1- 15" x 29 1/2" plywood (top)
1- 7 3/4" x 28" plywood, top cut with a jigsaw for the offset look (front)
1- 1x2 @ 28" (Back support)
8- 3/4" x 3/4" x 14" (cut 1x2's in 4- 14" sections, then split them on the table saw) (shelf supports)
3- 28" of the 1 3/4" colonial trim (shelf trim)
2- 31" with 45 degree mitered ends of the 2 3/4 colonial trim (top and bottom rim)
4- 15 3/4" with 45 degree mitered ends of the 2 3/4" colonial trim (top and bottom side trim)

Tools
Tape Measure
Speed Square
Pencil
Safety Glasses
Hearing Protection
Kreg Jig
Drill
Circular Saw
Miter Saw
Table Saw
Brad Nailer
Power Sander
Level
Drill Bit Set
General Instructions

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!

Instructions

Step 1

Start by attaching the shelf supports to the sides of the bookcase. *All of the supports are attached 3/4" from the fronts of the sides. The bottom of the bottom support is 1/4" from the bottom of the side. The next support is 18" from the bottom of the side. The next 2 supports are 14" from the bottom of the previous support. I found it easier to measure and draw all of the lines, then countersink holes(3 on each support), then glue and screw all of the supports to the sides at the same time. Do this for both sides.
*Remember the other side will mirror this side, it will not be exactly the same.

Step 2

Attach the bottom and front to the sides with pocket screws and glue. Always check for square.

Step 3

Attach the top support with pocket screws.
*You may wish to pre drill pocket holes for attaching the top through the back support and through the sides.

Step 4

Step 5

Step 6

Step 7

Attach the shelf trim with a finish nailer, glue, and clamps.
Wipe off any excess glue.

Step 8

Attach the top and bottom trim with a finish nailer, glue, and clamps.
Wipe off any excess glue.
If you only trim out the front of the unit, you will able to bank the bookcases together if you make multiple units.
If you wish to create a stand-alone unit, you can trim out the sides of the top and bottom as well, you just have to cut the trim accordingly atth a 45 degree miter on a miter saw.

Finishing Instructions
Preparation Instructions
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth.

It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
Finish Used
Wood conditioner (follow instructions on product)
Minwax Polyshades Antique Walnut, 3 coats, sanded with 0000 steel wool inbetween coats.

Comments

ana8178

Sun, 01/22/2012 - 10:05

I asked you about your plan under guest when I saw it and loved it!! Thank you so much for the plan, this is my next project! I will post pics on here when I'm through.

Chef Sowa

Sun, 01/22/2012 - 18:10

The minwax polyshades are a 1 step stain and polyurethane sealer. Sanding with the wool gives the next coat something to hold on to, as you don't wipe it off, it's pretty much treated like paint. Plus it cuts down any bubbles that may have gone unnoticed.