tweets >>

my other projects >>

My First Project (Home Depot Inspired Bookcase)

Printer-friendly versionPrinter-friendly versionSend to friendSend to friend
Additional Photos
My First Project (Home Depot Inspired Bookcase)
My First Project (Home Depot Inspired Bookcase)
My First Project (Home Depot Inspired Bookcase)
My First Project (Home Depot Inspired Bookcase)
My First Project (Home Depot Inspired Bookcase)
About This Project

My wife was watching TV and she saw a Bookshelf on a Home Depot commercial with diagonal shelving. She kept telling me how much she wanted a bookshelf like that. So, for my first wood project ever, I decided to try and tackle it for her. It is slightly over 7 feet wide and a little over 6 feet tall. I am currently trying to learn sketchup8 to create plans for this project.

Unfortunately I didn't use a certain plan from Ana's site for this project, but you can find any bookcase plan and place the diagonal shelves in place of the horizontal ones.

Estimated Cost: 
about 500 ( because I am a novice. Im sure someone with more experience could build it for much less depending on type of finish)
Estimated Time Investment: 
Week Long Project (20 Hours or More)
Required Skill Level: 
Starter Project
Type of Wood: 
Oak plywood, poplar hardwood, pine moulding
Finish Used: 
Benjamin Moore Black with a pearl finish
Pin it
Lady Goats's picture
 #
Wow.

Just... Wow!

 
C.Lang's picture
 #
Thank you.

Thank you very much.

 
loniwolfe's picture
 #
Beautiful!

So you totally just solved my no fireplace dilemma! I think I'm going to take your design here and leave an open space for some electric logs. Thank you so much for sharing, it is really stunning!

 
 #
I second that Wow!

This is your first project? Seriously! Fab!!!

 
 #
Very cool

Very cool. How did you cut the slots for the interlocking shelves?

 
C.Lang's picture
 #
Slots

Those were challenging because, as I stated before I am not even a beginner. I was going to try and use my little trim router to cut them but I learned quickly routers cause much saw dust. I don't have a router table and my router is small. I decided to use my miter saw. I measured out where the slots should go and Cut the outside boarders of the slots with my miter saw. I don't have a jig saw either so I chiseled the the remaining piece to form the slot. I then used my small trim router to smooth out the slots. After I got in a groove it went pretty fast. It was a lot of Slots. Like I said before, I am very new and I know there are easier ways to do this lol. Just a hint..If you ever use interlocking slots and plan on painting the project, I wouldn't make the slots exact to the bare wood. The primer and paint add to the thickness of the wood so it is important to take this into consideration before cutting the slots. Again, very new to this.

 
 #
Your not new anymore...

I don't think that you can say that your "new to this" any more. You cut your teeth on quite an ambitious project. You did a fantastic job! And just wait till you learn sketchup, the FUN you will have! Keep up the great work and keep posting! Can't wait to see your next project!

 
 #
I've never seen a diagonal

I've never seen a diagonal bookcase before, but I like this one. You'll never have to worry about straightening books that have fallen on their sides either.

 
 #
Vertical bookcase

This is really cool.

 
Debi G's picture
 #
So impressed!

This book case looks truly expensive! My excuse is always a lack of tools, but look what you did with what you had! Everything is square and precisely done.

 
C.Lang's picture
 #
Thank you

Thank you for your kind words. I appreciate all the input I have been getting. I look forward to posting more projects and getting more ideas.

 
 #
I really hope you post your

I really hope you post your plans! You did a nice job. I'd like to use a very scaled down version of this to make a wine rack in an open cupboard we have over our sink. Might have to pick your brain later. ;)

 
mrs2tone's picture
 #
Great Job!!

I saw the same commercial your wife saw, and kept trying to describe the bookshelf to my husband. Now I can show him. Thanks for posting,and I hope you figure out Sketch Up so we can see your plans!

 
C.Lang's picture
 #
Sketchup

I have started to figure it out a little bit. I thank you for the comments and am close to finishing the plans. Again thank you for your comments

 
 #
Beautiful

My daughter loves to read, I am going to see if my husband can turn this into a headboard.I will post pics if it turns out! Great Job!

 
C.Lang's picture
 #
Headboard

That would be an amazing project. If your husband does convert it, I would love to see the final results.

 
 #
Awesome!

What a fantastic job you did! I love this!!

 
 #
Love it!

And I second the headboard idea!

 
 #
Wow! That is wonderful...I

Wow! That is wonderful...I have a similar one that I LOVE and wanted for years. It was in the Pottery Barn Catalog and OUTRAGEOUSLY priced...I don't remember exactly the $$. When "Hold Everything", a subsidiary of PB, went out of business, I got the second to last one they had in stock for $200. AND...When I saw the HD commercial I realized I might be able to make a more custom version someday. Your story inspired me to plan something, and also to perhaps even open up and learn SketchUp which I downloaded months ago...Look forward to more projects!

 
 #
whoa. like. dang! i want

whoa. like. dang! i want one!!!

 

Post new comment

The content of this field is kept private and will not be shown publicly.
  • Web page addresses and e-mail addresses turn into links automatically.
  • Lines and paragraphs break automatically.

More information about formatting options

By submitting this form, you accept the Mollom privacy policy.

Not Much >>

What's going on up here in Alaska.

Momplex Cam >>

We are DIYing our moms a Duplex in Alaska! Check out our progress so far as we owner build a home, step by step. Read the Momplex blog here.

Recent comments

User login

Connect with Facebook
Sign in using Facebook

I'm Speaking At:

Haven Conference 2012

Please Visit Our Sponsors!


Pin It