$10 Cedar Cubby Shelf

Primary tabs

$10 Cedar Cubby Shelf

How to build a cubby wall shelf from cedar fence pickets! Free plans from Ana-White.com

HANDMADE FROM THIS PLAN >>

Projects built from this plan. Thank you for submitting brag posts, it's appreciated by all!

Author Notes: 

Well, I must say, I think I've been spotted in Carhartts and work boots one too many times ... because a big box came in the mail the other day and had me squealing with delight.  

My cousin Angela owns Bedazzled Boutique, a trendy online jewelry and fashion store where you can buy a bubble necklace for not $150 (I love JCrew too, but come on, who can afford that?) 

Try $25!!!!

And she's got very reasonable prices on a whole lot more than the bubble necklace!  I loved so much of her jewelry, I ended up ordering more than I could store!

So what's any gal to do?

Why, get her saw out and start cutting fence pickets, of course!

A couple of hours, a big pile of sawdust later, and I turned 6 Fence Pickets (that I purchased for $1.65 each) into this!!!!  Not bad for less than $10 in lumber!

The plan is to hang the cubby wall shelf system up in my bathroom, but due to lighting issues in Alaska right now, I photographed the project on an empty wall space.  The fence pickets were far from perfect - going on two years laying in a pile in my lean-to, but I loved the character they brought to this piece, imperfections especially!  And I don't know if I'll add stain or paint.

I just kinda love the raw wood.  It is beautiful.  

But then again, what doesn't look good with these pretty accessories?

Okay, that might be a stretch!  Fence pickets are much prettier than Carhartts!

For this project, I choose to notch full length shelves instead of attaching little shelves or dividers.  I really thought this part was going to be tough, but it ended up being super easy - maybe even easier than cutting a bunch of tiny little 5" long shelves and certainly easier than trying to attach all those little shelves.  And the finished look is much better because everything lines up perfectly and there's no nail or screw holes to hide!

What I did first was mark the notches out on the boards.  I made the notches a tiny bit past the half way point of the board just to give me a wiggle room.

Then I clamped multiple boards down, with cut overhanging my work table.  Here I've got two boards clamped, and actually got away with cutting three as well.

Then I cut on the line with my jigsaw.  I cut on the line just to give me some wiggle room when fitting the shelves together, but for more precision, you can cut inside the line, and then sand notches to get to work together seamlessly.  

Notice that I only cut the side lines.

To finish the cut, I simply used a 1/2" wide chisel and gave it a quick tap and the pieces fell right out.  You could also use a flat screwdriver.  Remember, this part is hidden inside the project.

Once you have the pieces all cut out, well, it's time to start assembly!  Follow the plans below and you'll be on your way to the cutest little cubby shelf ever ... for about $10 in .... yep, fence pickets!

Happy Building!

Ana

PS - Hope you take a second to meet my cousin Angela and check out her beautiful boutique! 

Shopping List: 

5 fence pickets - I used dog eared cedar ones (recommed getting 6 in case one splits or you have to cut around knots)
1 1/4" finish nails
wood glue

Tools: 
measuring tape
square
pencil
hammer
safety glasses
hearing protection
circular saw
jigsaw
nailer
General Instructions: 

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!

Dimensions: 
Dimensions shown above.
Cut List: 

2 - 1/2" x 5 1/2" fence pickets @ 32 1/2" long (vertical dividers)
7 - 1/2" x 5 1/2" fence pickets @ 16" long (horizontal shelves)
2 - 1/2" x 5 1/2" fence pickets @ 36" long (sides)
7 - 1/2" x 5 1/2" fence pickets @ 17" long (back - optional or you could use plywood)

Step 1: 

First cut the vertical dividers. Mark the side you start measuring from - this will be the bottom. Clearly mark this - it is important because if your boards aren't exactly 1/2" thick (mine were almost 1/16 wider in width) you'll be off that much.

Step 2 Instructions: 

Then cut five of the seven boards in notches. Again, mark the side you measure the notch outs to keep everything square and even.

Step 3 Instructions: 

With your vertical divider boards with the marked end down, add the shelves, marked ends all to either the right or left for consistency. You may need to use a mallet to get the notches to go in, or sand some tight spots.

Step 4 Instructions: 

Next, mark the top and bottom shelf 5" and 10 1/2" in to match the notch outs you did in step 2. Match up with the side you measured from matching the marked ends of the notched shelves.

I nailed on with 1 1/4" finish nails and glue.

Step 5 Instructions: 

Next, start at the bottom of your sides and mark as shown in diagram. Then line up marks and glue and nails sides on.

TIP: If you want to cut the tops in a curved pattern, clamp both sides together first, draw out your pattern, and cut as one with a jigsaw.

Step 6 Instructions: 

Originally I was going to slap 1/4" plywood to the back, but thought that the cedar would be prettier and cheaper. So I just cut boards and added to the back. For the top, I simply cut it down to size with the jigsaw.

Preparation Instructions: 
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
Project Type: 
Skill Level: 
Style: 

Comments

I love this! I don't have that much jewelry but my daughter has a rock collection that would look awfully cute in those cubbies:-) The strangest thing is that they don't carry cedar fence boards at the local blue store here...

Very nice, I can see this having so many uses. BTW - I placed an order from your cousin. Adorable stuff! ;)