Pedestal Trestle Dining Table

Primary tabs

PDF versionPDF version
90'L x 40 1/2"W x 31H

These are the basics of the wood size, i will add totals later today.


Common Materials: 
2 1/2 inch pocket hole screws
Kreg Jig: 
Cut List: 

To be added

Cutting Instructions: 
To be added
Project Type: 
Skill Level: 
Estimated Cost: 
General Instructions: 

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!


Variation of the Pedestal Table on this site. This table is 90"L x 40 1/2"W x 31"H

Finishing Instructions

Preparation Instructions: 
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.


I saw this table the day it was posted and knew immediately that this was the kitchen table I've been looking for. I'm anxious to get started and I'm wondering when detailed plans might be added. The "I will add totals later today" in the materials and tools section has been there since this table was added. Thanks!

This table is beautiful! It said that the cut measurements and directions would be posted later and I was wondering when that might be. I'd love to make this table for our dining room! Thanks!

This table is beautiful! It said that the cut measurements and directions would be posted later and I was wondering when that might be. I'd love to make this table for our dining room! Thanks!

Hey! This is the version of the 3 pedestal table I've been looking for! So excited you have this available! Do you have plans yet? Are they posted somewhere else?

Thank you for all you do!!

Question! Would I be able to achieve similar results without planing any boards? Simply by using stock lumber I mean?

I am almost done with the plans this is my first attempt with sketchup so it has been a process to say the least.

On the table top, I used stock lumber, and I did not have a planer. I used my table saw to cut an 1/8 of each side of boards to removed the rounded edges. Then glue and kreg jig them together. cleaned off any glue that squeezed out. Then I took my belt sander and sanded till all creases were smooth as a baby bottom. Sometimes I get a crack or a gap and I used stainable ProBond wood filler and sand again. When stained it looks awesome.

I have rounded up all the tools I should I just need the full plan to get started. We only have a couple sunny months here in Oregon for building outdoors, so I'm anticipating the detailed plans for this project. Any chance they will be available soon?

Thanks ~

It's been over three months since this design was originally posted and roughly seven weeks since you posted that the plans were "almost done". Can we expect that plans will actually be provided? I love this table and really wanted to make it, but summer has nearly come and gone and I could have already built a table from a different design.......

Not a very nice post to someone who provides her designs free of charge. You have no idea the reasons behind why she has been unable to post the plans. You post your comment like she owes you something. Nothing stopping you from finding other plans and moving ahead with you project. gheesh.

P.S. to everyone else - sorry to derail these posts by commenting to this. I can't stand rude people.

Just came across this table. Can't wait to make it. I appreciate you providing your plans. No doubt you are busy being a mom. I know how that is! Looking forward to the plans and having a fall/winter project. Thank you!

sorry folks, I have been struggle using sketchup on these plans as I have never used before. Anna is not responsible for the plans being online for this as it was mine. :0) I will do my best to get finished asap.


Seeing that you just posted jst 2 days ago I can sertainly be a little more patient. :-) Not in a rush really. I have, infact, drawn up a design based
on your image and the orig 3 pedestal table. Curious as to how close I'd come. Considered sending them out to others but I really didn't want to rain on any parades. Looking forward to your completion. :-)


This table is lovely! I built a table very similar to this one except it had more of a box type pedestal in the middle. I am curious how the underside of the table top is attached and what it looks like. Will you post a picture of the underside of this table top please?

You can look at the original plans for the Three Pedestal Table on Ana's sight here. That should help you figure out the underside leg mounting.


I love this table. You did a really great job. I actually plan on using different designs from different tables on this site but use your legs. Looks just like the ones from the triple pedestal table but with its own twist. Keep up the good work...

Just wondering if you can give the basic cuts.
I can kind of tell the 2x8s for the top.. What did you use for under the top planks?
Also was it (3) 2x4s butted up together for the base? How did you link them together ? Can you post a closer view of the base? So I can try to figure it out?



Projects built from this plan. Thank you for submitting brag posts, it's appreciated by all!