Outdoor Bench with Arbor

Primary tabs

Outdoor Bench with Arbor

Free arbor bench plans from ana-white.com

HANDMADE FROM THIS PLAN >>

Projects built from this plan. Thank you for submitting brag posts, it's appreciated by all!

Author Notes: 

Hello DIY Friends!  Happy Monday!

What happens when you mix two of your favorite DIY projects together, and partner up with one of your favorite DIY blog friends?

This happens!

A long while back - like last summer - my friend Gina saw this child's arbor bench project I posted (worked on with my good friend Kirsten from The Crafting Chicks)

And asked me if we could make an adult sized plan too!

Well, bringing a new baby in the mix has put everything into sloooooow motion, so it took me months to work on the plans (wish I was one of those super talented moms that can work and feed the baby at the same time, but I'm just not that coordinated).

Like it was May by then ....

And my friend Gina from Lady Goats saw this pergola I designed for the Home Depot/Ryobi commercial (plans are available here) and asked if we could style the arbor bench like it.

I so love how this turned out!

Gina from Lady Goats (with a little help from Mr. Goats) did an amazing job building this arbor bench!  Those tails, that lattice work .... swoon!

Of course, we've got free plans below, but make sure you read Gina from Lady Goat's full building post - she's got TONS of tips and tricks to help you through your own build!

Thank you Gina!

Plans follow!

XO Ana + Family

PS - Congrats to ED over at RYOBI Nation for winning BIG by submitting this Pergola for the May Project Challenge!  (The May Challenge was to build a project from the RYBOI Pergola commercial and share on RYOBI Nation for a chance to win $500 in tools).

The June Challenge is up - check it out for a chance to win up to $500 in tools!

Shopping List: 

4 - 4x4 posts @ 84" (legs)
4 - 2x4 @ 21" (side supports)
2 - 2x4 @ 91" (bottom seat front/back aprons)
4 - 2x6 @ 91" (top lower rafters)
7 - 2x4 @ 48" (top upper rafters)
4 - 2x4 @ 28" (seat supports)
2 - 2x4 @ 60" (back support framing)
5 - 2x4 @ 15-1/2" (back support framing)
7 - 1x6 (or 2x6) @ 60" (seat boards)
6 - 2x4 @ 33" (side shelves)

NOTE: Recommend exterior screws

2 inch screws
2 1/2 inch screws
2 1/2 inch pocket hole screws
Tools: 
measuring tape
square
pencil
safety glasses
hearing protection
drill
circular saw
jigsaw
sander
countersink drill bit
General Instructions: 

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!

Dimensions: 
Dimensions shown above
Cut List: 

4 - 4 x 4 x 8
12 - 2 x 4 x 8
1 - 2 x 4 x 10
3 - 2 x 6 x 10
5 - 2 x 6 x 8
1 - 4 x 8 lattice panel

Step 1: 

Start by building the two ends by attaching with pocket holes the side pieces to the posts.

Step 2 Instructions: 

Next, attach the front and back seat aprons to the outsides of the posts.

Step 3 Instructions: 

Attach lower rafters to tops of posts.

TIP: Predrill holes and start screws on ground first.

Step 4 Instructions: 

Cut the upper row of rafters and notch and place on top. Screw down.

Step 5 Instructions: 

Add seat framing either with pocket holes or 2-1/2" countersunk screws.

Step 6 Instructions: 

Build back seat framing and attach between posts and top of back seat support.

Step 7 Instructions: 

Place seat boards on top of seat, and to back seat framing.

Step 8 Instructions: 

Add lattice to inside of the sides - you may wish to add additional wood trim supports around the lattice panels.

Step 9 Instructions: 

Finish off ends with boards (perfect spot for a plant!)

Preparation Instructions: 
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
Project Type: 
Estimated Cost: 
Room: 
Skill Level: 
Style: 

Comments

Awesome plans as usual Ana! I can't wait to make this someday. Thank you for all the time and inspiration you provide on your site!

One small side note though: the shopping list and cut lists are swapped in this plan.