I added folding screens to my garden bed to prevent my dog to go in it. It can also discourage hares, cats and other animals. The folding screens make it easy to work in your garden.
My wife and I were looking for a larger table for our deck and after searching and seeing that everything out there was 300 dollars and up for something decent I decided I would try building something. This table was perfect for our needs and looked easy enough for me to put together. The most time consuming part was staining all of the boards as I went but it was totally worth it in the end. I also deviated from using screws and used my nail gun along with some glue to put the top frame together and the slats on but I did use some 2inch deckmate screws to attach the legs. One problem I did run into was I was about half a board short on the slats which wasn't a big deal just ripped one on the table saw, not sure if I miss measured or what but either way. We love our table and will entertain around it for years to come.
Decided our old play set needed an addition, landed on these plans of Ana's. Sat on them and mulled them over for months. Once the wife said something about adding on to it I made the purchases needed. Connected the two platforms with a bridge. I used 4"x4"x10' for the runners, same boards as the decking for the platform of the bridge(5/4"x6"), 2x4's and 1x4's for the railing. If you look at the 3rd photo, I had to chisel out the 4x4 post to get the 2"x6"x12" support to fit correctly. This should measure 2"x6"x13". Another change I made was to cut the bottom and top trim pieces longer on the front and back sections so that the trim would cover the framing of the gable end walls (see last photo). my son wanted windows so I faked in some windows with scrap 2x2's. I used 2x6's as supports from the 4x4's to the 2x6 framing (see photo 3) I added the monkey bars about a month before deciding to do the platform/deck and playhouse. The ladder is based loosely off of a couple of plans I found online. I was able to do all of this work myself except for the roof. Need my dads help to lift the plywood, he then helped me with the rest of the roof.
My wife wanted matching bookcases for our library rather than the hodgepodge collection we had assembled over the years. We looked at several different options but the trick was getting them to our house in a cost and time effective manner. We came across the Willy Bookcase plans here and, after pricing the wood vs. pre-built options, decided to strike out to build our own bookcases.
The library took 5 McMansions, 1 Highrise, and 1 3-Bed/2Bath bookcase. We liked Ikea's Billy corner bookcase set, so we purchased a corner bookcase bracket from them to create the effect and stabilize the Highrise between two McMansions.
We decided to do the entire length of the bookcase sides with shelf holes to allow for maximum flexibility in spacing of the shelves. We fixed the middle shelves across all units to match the top of the short 3-Bed/2Bath.
The simple design made the project simple overall - a single bookcase is an easy weekend project. Since we decided to use stain with wipe on poly, finishing took the vast majority of the time (four hours to cut, sand, and build, 44 hours to finish...) Purchasing a good shelf pin jig and making consistent measurements is a necessity for mass producing shelves with consistent spacing on the shelves.
Great plans, Ana! I swapped out the wood for PVC trim, and used stainless steel screws to hopefully make this thing weatherproof.
My family has started raising quail recently and I built their first home while they were still in the incubator. I have never done any wood work before, so this turned out much nicer than I expected! I followed the suggestion of having the brooder part on the top instead of the bottom and omitted the extra shelf. Two 5-gallon buckets fit nicely below the chicks. Since the quail are so small when they hatch, I used 1/4 inch hardware cloth for the "floor" but it wasn't long before that was too small so we had to change it to 1/2 inch. I am going to make a tray with each size of hardware cloth on it to make it easier to change out for next time, because they really do need both sizes.
I finished my first project. Although there are some cosmetic errors, I think overall it’s amazing. We had a lot of wood left behind by the builder of our log home. So, I was able to use a lot of that. I made some adjustments to the height of the boxes to help the back!
Michelle M - Jefferson, NC
The published plans for this were great. This was my first attempt at a project like this. I have always liked the idea of dining at a large table outdoors and the farmer's style is appealing to me. I adjusted the length to fit my deck, but also made a few changes for aesthetic purposes. I notched 4x4s rather than join a pair of 2x4s for the legs. Added caps to the screw holes rather than filler and used pegs to secure the top planks in addition to screws from the bottom. The frame and top were stained/sealed with Cabot Australian Timber Oil.
I had a big empty wall in my den/man cave, so I decided to build a dartboard cabinet instead of just hanging a dartboard on the wall. No plans for this, I just made it up as I went. Measured twice, sketched it out and cut as I went.
I use pine 1x4's for the frame and back. 1x3's for the accessory box, 1x2's for the door frame, and poplar strips for the doors and door braces. The darts are held by 6" long 2x2's with holes drilled.
Wood screws, finish nails, and small brads were used to hold everything together.
The chalkboards are simple MDF's cut and sprayed with chalkboard paint. Overlay hinges are used for the doors, and the dartbord is held on with screws from the back so it can be replaced when needed.
The Alabama A is hand-painted.
I build the bar table with an x-base and created some stools using part of the plan. We really wanted backs on the stools so I made them up!
Wed, 11/14/2012 - 18:16
Hard to believe that you are a beginner. Fantastic work. Keep it up and the whole home will be furnished.
Sat, 04/13/2013 - 13:47
I'd love some information on the backs. My husband has a bad back and it's a necessity, but I'm a beginner and not sure how you did it/
This bench is freaking huge but I love how it turned out. A lot of pocket holes for the back so it took a lot of putty to cover those up but that’s to be expected. Proud of this one.
A very enjoyable project. I'm relatively new to diy woodworking projects but these plans make it so much easier.
Thanks.
I modified this plan from square to rectangular to fit my space. It is exactly what was needed! Modified size: 27.5" x 55"
Sat, 11/07/2020 - 11:19
Looks perfect in your space! Thanks for sharing:)
So.....my Daughter has this American Girl doll, and she loves it. Then she saves up $75 to buy this HUGE Horse...why? I have no idea, but she loves it.
At Christmas time, Ana White was so kind to post diagrams for building a Horse Stable and with a few minor changes (shingled roof, golden hooks, some stain) I built it with my new Kreg jig (that was my Christmas gift from Santa).
Hope you enjoy the pictures . . .
Ana - Thank you, I enjoy your site and you certainly will be hearing from me in the near future.
Thanks for all you do :-)
Sat, 01/26/2013 - 09:59
I love your modifications. What a great idea to use shims for the roof! I might have to copy this. Great job.
Sat, 01/26/2013 - 10:15
Oh I love this!!!! I can't tell you how giddy up happy I am to see the horse stable! Love the roof and the gold hardware too - so cute! Thanks for sharing, truly made my day!
Sat, 11/23/2013 - 19:18
Oh, I'm in love with the shingles!
My daughter is getting her third AG doll, Saige, for Christmas and my sisters are getting her the horse too. Well, you can't have a horse without a stable too, right?
I've got all the supplies to build the stable and now all I have left to figure out is how you attached the shims to the plywood for the roof. Any suggestions would be fantastic and much appreciated!
I took some ideas from an Ana White wine rack I saw and made this Pantry for our kitchen. Pretty happy with how it turned out.
Created but Modified from the plans found on here, my daughter has a great new bed. This bed saved a ton of space in her very small room. PLUS it allowed her to have an area to do her homework and all the art projects she does! Very easy build. Took a day to build and another to paint.
My Dad made a few cutting boards for christmas. I've added a few additional photos and tips on my blog - http://www.woodworkingfourdummies.com/blog/more-cutting-boards.
thanks for looking.
Ian
Tue, 01/13/2015 - 04:28
Hi Ana! Love your site!!!!!! Please tell me, did you use just mineral oil in order to make this non-toxic finish? I guess you would have done some posts including this kind of information, but I can't find it. Regards from Argentina! =)
Thu, 01/15/2015 - 09:45
Only mineral oil was used, it is food safe grade and can be ingested. Mineral oil isn't a durable finish like polyurethane but it is safe.
Thanks for the free plans. I did have to make modifications for the doors. i hid the hinges to give it a clean look. i used cedar for the trim and Plywood Siding Panel T1-11 4 IN OC (Common: 19/32 in. x 4 ft. x 8 ft.; Actual: 0.563 in. x 48 in. x 96 in.) for the doors. i used a metal flashing for the roof so it will vent.
My kitchen needed a rustic pot rack to hang all my pots and pans. Instead of paying way too much money, I decided to get exactly what I wanted by making it myself. $20 worth of 2x6's and spray painted hardware purchased at The Home Depot in an oil bronzed was all that was needed to create this rack. I attached the hardware with metal screws to give it an even more rustic feel.
