Shaker Peg Board with No Saw Cuts Required

Shaker Peg
Difficulty
Starter Projects
| Print this plan

It's possible build a pretty attractive and useful piece that really only requires a drill, hammer, sandpaper and some finish.  No saw cuts at all.

You need a single board. You can go to Rockler (a woodworking company that has stores nationwide and is on the web at www.rockler.com) and purchase a 24 inch by 3 3/4 inch by 1/2 inch piece of walnut at a cost around 10 or 12 bucks. The Local Home Depot carries the 1/2" thick 2 foot boards in Red Oak for 5 or 6 bucks too.  Either way you go, make sure it's straight and flat.

Next you need shaker pegs. Rockler has these. The local Home Depot did not.  The Local Ace Hardware did.  The ones from Ace were made of Birch which is fine.

Preparation

Shopping List

1 24 X 3 1/2 X 1/2 Board
3 or 4 shaker pegs

Common Materials
120 grit sandpaper
Cut List

None

Cutting Instructions

None

Tools
Tape Measure
Drill
General Instructions

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!

Instructions

Step 1

Decide if you want a special edge. The item pictured has a sort of fancy edge created with a router but a simple chamfer is all it takes to give it a more well crafted appearance. To create the chamfer place board in a vice and use a block plane or a sanding block held at a 45 degree angle to your board. See Image. The block plane will leave a crisper edge, but not everybody has a plane handy. The trick is to keep it held at 45 degrees. Practice on a piece of scrap if possible.

Step 2

Sand the faces of the board. Stepping up through the grits 150, 180, and 220 is best. At a minimum, sand it well with 150 grit sandpaper, using a sanding block. There is no need to sand higher than 220 grit.

Step 3

You need to make a decision here. You can finish, then drill or drill then finish. It's easier to finish then drill but the drilling process can craze or crack the finish near the hole. If you finish after drilling make sure to keep the finish out of the hole as it will reduce the glue strength. A piece of properly sized sponge should work. Either way you'll find it easier to finish before gluing in the pegs.

Measure and drill the holes. See image for measuring. The size will depend on the shaker pegs. Make sure to measure them as close to the step as possible as they are usually tapered. The simplest approach to drilling is to drill the holes all the way through. Truth be told, nobody will know since the back will be against the wall. A more complicated but 'cleaner' approach is to drill them to the 3/8" depth of the plug at the bottom of the pegs. Knowing when to stop is the trick. You can measure 3/8 up the drill bit and place a piece of blue painters tape there. Stop drilling when you get to the tape.

Step 4

The finish shown here was satin General Finishes Arm-R-Seal. MinWax Wipe-on Poly would be another option for a similar finish. This was used without staining on the walnut. You could stain it though if its walnut it seems pointless to hide the natural beauty of the wood with stain. The pegs are stained (prior to gluing) to match the Walnut. The ones shown here were actually colored with a Dark Walnut Dye, but a dark stain would work too.

Finishing Instructions
Preparation Instructions
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth.

It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.

Comments