DIY your own bathroom vanity with free plans by Ana White. Farmhouse style vanity with turned legs and open bottom shelf. Use with a store bought countertop and sink or build your own. Includes full step by step diagrams with instructions.
4 Turned Vanity Legs
1/2" plywood for drawer panels and pullout drawers
1 1/4" pocket hole screws
I'd love to give you just a simple cut list, but because all legs are going to vary, it's better to cut your boards to fit your legs.
Cut list is for Osborne Wood Vanity Leg 2401 - I highly recommend adjusting your cut list to match your legs and vanity top - especially if you are using a store bought vanity top.
4 - Turned Vanity Legs with bottom stretcher block
4 - 1x3 @ 15"
1 - 3/4" plywood @ 19" x 15"
Front/Back Face Frames
I opted to leave the back open for easier access to plumbing, but the back could also be solid plywood.
4 - 1x3 @ 42"
4 - 1x2 @ 14"
2 - 1x2 @ approx 15" - cut to fit distance between bottom stretcher blocks for bottom shelf (measure) mine actually matched the upper stretcher block
2 - 1x2 @ approx 42" - cut to fit distance between bottom stretcher blocks for bottom shelf (measure) mine actually matched the upper stretcher block
3/4" plywood cut to fit for bottom shelf, notched out for turned legs
See in plan
Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!
We built the two leg sets flush to the insides because one side is against the wall and the other side will hold the toilet paper hardware. This also makes it easier to mount drawer slides later on. We even considered adding a built in magazine rack.
We used 3/4" pocket holes and 1 1/4" pocket hole screws to put everything together.
Then we built two identical face frames for the front and back using again 3/4" pocket holes and 1 1/4" pocket hole screws. The face frames were then attached to the two leg sets.
For a longer vanity, you may wish to use 3/4" plywood instead on the back to beef it up - or if you are putting a heavy vanity top on.
IMPORTANT: Depending on your sink size and location, build these face frames to suit. I highly recommend for store bought vanity tops and sinks to purchase first, measure and leave plenty of space for the sink. We errored on the safe side and left the standard 24" opening for the sink in the center (25 1/2" to the outsides of the face framing to allow for shelf sides of 3/4" thickness each).
Then we finished the trim for the bottom shelf. Our bottom shelf stretcher blocks matched the top, so we were able to just use the same length boards as the top face framing.
We kept these guys flush to the outside just to maximize storage space underneath, but this ended up forcing us to have to place the pocket holes to the outside (turned legs kept splitting when attached to inside because there just wasn't enough wood to bite into). No biggie for us because we are painting, but for a stained finish, you may wish to inset the bottom trim a little to prevent this issue.
We cut the plywood to fit in a rectangle, then used a jigsaw to notch out the legs. Then we drilled 3/4" pocket holes around the underside of the shelf and attached with 1 1/4" pocket hole screws to shelf trim.
For heavier loads/longer spans an easy trick to beef up the center of the shelf is to attach hidden center "legs" under the bottom shelf.
The partitions keep contents seperated and also support the end of the center shelf. We ended up not going all the way to the top with ours just because we opted for the pull out drawers and didn't feel it was necessary. We used 3/4" plywood scraps but could have used a 1x3 or 1x4.
This also gave use better access to installing the pullout drawer slides later on.
Again, just attached with 3/4" pocket holes and 1 1/4" pocket hole screws.
We opted for a low maintenance all in one sink/vanity top made of a solid surface material. As much as we'd have loved to DIY a tile topped vanity, I bet on this solid surface one with seamless sink to last longer and be easier to clean for Mom. Crazy how the top cost more than the vanity itself!
When we do the plumbing (hopefully soon!) I'll share how we attach the top.
It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.