Ultimate Changing Table

Newest Video! I love creating, here's what I'm up to!

Submitted by Ana White on Fri, 08/22/2014 - 09:38
| Print this plan

Free plans for an Ultimate Changing Table - from ana-white.com

Baby Sew Woodsy has arrived and is all cuteness!

Oh. My. Goodness.

I may of course be a little partial to baby boys right now ....

Yep, that's our little man at last night's DIH Workshop held at The Home Depot (I'll be posting about the event and a special treat next week).

I got the great honor of designing plans for Baby Sew Woodsy's dresser a while back - thank you for all the love and sharing of it!

John and Katie AKA Baby Sew Woodsy's parents, were kind enough to work with me again on Changing Table Plans for little Ryder's nursery!

How beautiful is this changing table?  I feel very honored to be a part of this beautiful and special changing table build!

You can build it too!  The plans follow, and for more photos, finishing details, and Sew Woodsy's building post for tips and tricks - please go here now.

Have a great weekend.

XOXO Ana + Family

Dimensions shown above.


Shopping List

1/2 Sheet of 3/4” plywood or MDF

2 - 2x2 @ 8 feet long

3 - 1x2 @ 8 feet long

1 - 1x6 @ 10 feet long

1 - 1x4 @ 12 feet long

1/4” plywood piece at least 16” x 35”

2 - 1x3 @ 8 feet long (for topper)

1-1/4” pocket hole screws

Cut List

4 - 2x2 @ 32”

4 - 1x2 @ 14-1/2”

4 - 1x2 @ 38”

2 - 3/4” plywood @ 14-1/2” x 38”

2 - 1x6 @ 14-1/2”

1 - 1x6 @ 38”

1 - 3/4” plywood @ 17-1/2” x 41”

1 - 1x2 @ 38”

3 - 1x2 @ 4-3/4”


4 - 1x4 @ 15-1/2” (sides)

4 - 1x4 @ 15-3/8” (front/back)

2 - 1/4” plywood @ 15-1/2” x 16-7/8” (bottom)

2 - 3/4” plywood or 1x6 @ 4-1/2” x 17-5/8” (front)


2 - 1x3 @ 41”

3 - 1x3 @ 16”

Tape Measure
Speed Square
Safety Glasses
Hearing Protection
Kreg Jig
Circular Saw
Miter Saw
Brad Nailer
Power Sander
General Instructions

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!


Step 1

Drill (2) 3/4” pocket holes on each end of the 1x2 @ 14-1/2” long. Attach to the 2x2 legs with 1-1/4”

pocket hole screws, flush to inside, keeping pocket holes hidden on insides.

NOTE: Upper shelf can be placed at any height. In this plan, the upper shelf is placed to allow 12” height

on lower shelf.

Step 2

Drill 2 - 3/4” pocket holes on each end of the 1x2 @ 38” long and attach with 1-1/4” pocket hole screws

to the 2x2 legs, at the same height as the side 1x2s. Keep 1x2s flush to inside of the legs.

Step 3

Drill 3/4” pocket holes around all four edges of the two shelves (14-1/2” x 38”), spacing pocket holes

every 6-8 inches. Attach inset to the 1x2 frames with 1-1/4” pocket hole screws.

Step 4

Attach the 1x6 side and back aprons with 3/4” pocket holes and 1-1/4” pocket hole screws. Also drill 3/

4” pocket holes on the insides of the aprons facing upward to attach the top in later steps.

*Note: the backboard should be flush to the outside of the legs.

Step 5

Step 6

Attach the shorter 1x2 boards to inside of drawer area. Then attach bottom 1x2 with glue and finish

nails - also use pocket holes to attach to legs.

Step 7

Trim out around top with molding or 1x1s to finish plywood edges. For a more finished look, miter


Step 8

Build drawers to fit openings and drawer slides. Install drawers in table with drawer slides, insetting 3/

4” to allow for the drawer face.

Step 9

Attach drawer face to drawers with 1-1/4” finish nails and glue, then attach from inside with 1-1/4”

screws. NOTE: It may be easier to attach handles or knobs before attaching the drawer faces.

Step 10

Build topper with either finish nails and glue or pocket holes. Bottom is not necessary. Can be attached

with a bracket on back side to keep in place.

*Note: We adjusted the 32” measurement to 30” to fit our changing pad and wipe container better.

Finishing Instructions
Preparation Instructions
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth.

It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.



Sat, 01/31/2015 - 20:32

Can you please help me with step 9? It says to install drawers with drawer slides, but I don't see anything in the shopping list about drawer slides, and I don't see anything about how to install them in the instructions. If you simply insert the drawers into the structure as shown above, it seems like they would be balancing on a small cross section of a 1x2 board. I assume that can't be right. Is there a missing step?


Sat, 12/05/2015 - 03:47

Hi All,

I was having the same issue so I added an extra 2x1 in step 6 behind the small bit in the center. I attached it with pocket hole screws and glue and attached the drawer slides on both sides. I've adde a picture of it to my bragpost. Hope it helps.


Sat, 03/12/2016 - 09:34

Can't for the life of me get flush 90 joints with a kreg jig and a 90deg clamp. Is this a common problem or is it unusual? New to using the system, so it's probably a user issue.

Free Plans Made Possible By Our Sponsors