Community Brag Posts

I saw this table on wyrmwoodgaming.com but I wanted to see if I could make it myself. I did it all in Cherry and used Tung oil to finish it. I have two coats of Tung oil on there for a finish. In all I paid about $800 for the cherry and flat steel I used for the magnetic rails on the sides.

I make and sell kids picnic tables on craigslist and a buyer asked about making one of these. I took it on and found the plans on here very easy! I now list these on craigslist also and hope to sell more before the summer is over.

Modified the classic bunk bed plans to fit crib size matresses for our 1.5 & 2 year old girls, loved how my toddler bunk beds turned out! 

Thanks for the instructions! Here's my version. I haven't built much of anything before, but I needed it in my basement to handle kids' stuff. My version is 18 feet long. I combined a 12-foot and 6-foot 2x4 to get that length, which meant less cutting, which I had done at Lowe's (for free). I used the 6-foot 2x4s throughout the shelf to ensure it was strong (in other words, I didn't want a 12-foot "section" and a weaker 6-foot "section" added on).

I was able to get everything in my car but the ride home was slow. I also had to use my egress window to get the 12-foot boards in the basement.

Total cost for me was about $170 including a couple boxes of screws and wood glue. I could've easily spent double the cost on store-bought shelving. Thanks for the plans!

We really enjoyed building this playhouse swing set for our kids.  We have a decent slope to our backyard, so we needed to sink our posts, which required a bit more work thank Ana's plans.  We also used a real window (my dad just happened to have in his garage) instead of the 3 open aired windows Ana's plans called for.  Inside we built a fold under table, shelf, and a chalkboard for thier entertainment.  

Farmhouse Coffee Table with a bit of Rustic "X" Coffee Table. Thank you so much for the plans. This was a nice build. I opted for pocket holes and panel glue up so for me, it wasn't a one day build. :)

Just finished up this unique TV console.  Built from reclaimed pallet wood. 

Just My Size Closet!

Built this from Ana's plans with a few modifications.

Started with a big empty box after ripping the old stuff out and finished with this look.

Adjustable shelves and all !

I got this Idea from Sausha's washer dryer pedestal post.  Before then i didnt know people even built pedestals for their washer and dryer.  Just purchased new front load washer and dryer and they wanted 250 bucks extra for each pedestal.  That is 500 bucks and is absolutely rediculous.  So i opted out of those and thought to myself maybe I can build something instead.  So I began my search online and stumbled across this post which seems to be the most popular pedestal build on the web.  I think sausha's build is fantastic and absolutely beautiful though I went another way with mine.

I tend to like to overbuild things.  Especially in this case, seeing as the washer weighs a beastly 200 pounds by itself.  I figured with clothes and water it would be about 235 pounds just for the washer.  I noticed that with the aluminum drawer pedestals that you can purchse with the washer and dryer the support is only where the legs from the washer and dryer will sit.  That was all I needed to get on my way.  Purchased some regular old douglas fir 2x4's, 4x4's, and a 4'x8' sheet of 3/4 inch plywood.  I opted to use fence post brackets to tie everything together because I didnt feel like driller pocket holes in each 2x4 when you were not going to see them once its all said and done.  The fence brackets are not structural so they lack ridgidity untill you tie everything together with the legs, slats, and top.  Cut the top from the 3/4 plywood sheet and used the left over plywood to cover the front and the sides.  I left the back open as it is not seen anyway. 

Total size of the pedestal is 56" wide x 31" deep x 12 3/4 inches tall, but you can build it as wide, deep or as tall as you need it.  When i was done putting it together.  I tested it by jumping up and down on it and I weigh 230 pounds.  So this thing is quite strong.  I finished it up by covering the edges where the plywood meet with Edge moulding and the bottom with baseboard to match my laundry room.  I used Behr premium plus ultra paint on most of it and, behr alkyd paint for the baseboards.  Gave the top a couple coats of General Finishes High Performance Polyurethane.  Which isnt neccessary but I opted to do so because of the weight of the washer and dryer and the General Finishes High performance dries harder than most other polys that I have used.  I only used it on the top though. 

Taking into account that I used the paint and baseboards left over from renovating my laundry room.  This project cost about 150 bucks.  200 if you have to purchase the paint and moulding.  Quite easy to do and though I made the cutes I needed with my table saw.  This can be done with a circular saw and a drill.  No exotic tools are needed.  Will post finished pictures when my washing machine and dryer are delivered on friday and they are sitting on top of the pedestal. 

I needed new bar stools for our new bar that we designed and built in our basement family/entertaining room. Regardless of where I was looking, these things are silly expensive. I also wanted a little more of a country/rustic look that would suit my husband and my likes. I used the Vintage Bar Stool plans but my husband isn't a small guy and we have friends that aren't classified under the small frame category either, I needed more structure. After thinking about it for a few days, I liked the rustic X look and used that from so many plans. I also am all about comfort and the padded upholstered seats was a must. Can't wait for my next project. BTW. The cabinets behind the bar also came from here I simply modified for what we needed. We get compliments on it all of the time. Love this website, thank you so much for making simple to read instructions for things I actually want to do. 

I used the Farmhouse Table plans and just extended the measurements to build an extra-long outdoor table that seats 12.