I loved working on this easy upholstered bench. It was so much fun and so simple. I followed the plan except I raised the bench to 20 inches, because my husband and I are quite tall. I also wrapped the fabric underneath about 1/2 inch and stapled it so it has a tighter look. Thanks for the plans Ana!

I had a ton of fun making this media console! It is my second big project, and I would still consider myself a beginner, but I paid very close attention to detail and I think it turned out great!

I stretched the console out by about 4 inches, so that if I ever decide to put my TV on it, it will fit.

Thanks Ana for your great website!

Thank you so much for the plans! Very excited for how it turned out!

I love the look of these shelves. I needed something for the wall space to either side of the kitchen window and sink. The ceiling slopes down at least a foot on that wall so there's less space for cabinets and putting up cabinets that fit the space wasn't working. Shelves were the answer. The pictures show only the left side of the window/sink, but I did put up a matching shelf on the right side. I used a 1x8 for the shelf and 1x6 for the back.

Love how this turned out! Great build, added a back to the table. It looks awesome in our living room.

I built a narrower version of the farmhouse table with a few modifications to be used as a temporary dining table, and eventual home schooling desk. I used 5/4 boards for the top and for the apron in order to get a smooth top and have a beefier support. I used a 4x4 for the cross brace with a half-lap to give more support to the stretcher and to stabilize the legs.

These Easy Three Cube Benches were my first project from Ana White's plans!  I love how the plans are broken down, making them easy to read and understand and I learned so much from the concepts!  The "build the box" concept is how I gained the confidence to build all of the furniture in my craft room myself!  I started with these Three Cube Benches, then designed and built a printer stand using the concepts I learned and, after that, finally finished an corner office/crafting desk.

Our big old house doesn't have a front hall closet, so I decided to make the Nursery Armoire for our extra coats and shoes. Since our ceilings are so tall I decided to make it the full 96" that I could get out've the sheet of plywood.
I also modified the plan to adjust the door heights so that the top would make good coat hanging and the bottom can be used for shoes and boots. I also changed the drawers to be on the outside instead of behind the upper doors.
I used 3/4" plywood for the box and pine for the doors and trim.
For the doors I pocket holed the frames and then routed an edge on the backside and stapled pine paneling to fill out the middle. This matches doors I made previously to make cupboards in our full-wall brick fireplace (and the hardware matches too).
I did the top trim as in the plan, and I decided to leave the bottom plain.
It's quite large! But in the space a smaller one would've looked silly, so I'm glad I went with the height.

I decided to paint it so that I didn't have to fuss with staining, but went with the same paint as the walls for the backs and undersides of shelves to lighten it up.

Can't wait to fill it up! ....just have to give the dark paint one more go-over....

Our mud room/laundry room is very busy with 2 boys and 2 adults. Scarves, gloves and hats are generally tossed here or there, usually far and wide when it comes to my boys.

My solution was a coat rack with cubby. Like most of my creations, it is a Kelley Special, all up in my head. I don't have plans, although I will make some when I make the next ones for me and my husband.

I used poplar 1x4's for the sides, bottom and back attachment and 1x6's for the front where coat hooks will be mounted, 2 small coat hooks on the sides, wood glue, and pocket holes to construct it.

If you add the time I spent on it, it didn't take too long, but it took a while since it was a few minutes here and a few minutes there. I am very happy with the final product, and we are starting to test it out now that the weather is cold again.

If you want to see more pictures take a swing by my blog: www.trekkiemom.com

Great instructions, easy weekend build. 

I made this as a gift for a friends Baby Shower. It's meant to mount on the wall and hold Baby's stuffed animals. After the Shower yesterday, it's half full of animals already!

I used pine, and a "walnut" stain by minwax. We only stained the structure part so the bars would look like they were a different material. I also used glue, a staple gun and my Ryobi Airstrike automatic nailer - it's a new toy for me, but one I'm in love with already :)

Please feel free to click over to my blog for details on how to help build yours! ---> http://projectjumanji.blogspot.ca/2013/10/what-ive-been-up-to.html

Conceal litter box make from plan http://www.ana-white.com/2012/10/plans/printers-triple-console-cabinet