Cindy Wood Console Table with Drawers

Submitted by Ana White on Tue, 09/10/2019 - 12:32
Difficulty
Advanced
| Print this plan

This pretty console table features two drawers and cubbies - it's perfect in an entryway or hall.  The top is table height.  It's made from 1x12s and 1x2s - so no need to rip plywood.  Paint or stain any color of your choice.  Free step by step plans by Ana White.

wood console table with drawers
 
We love this wood console table with drawers!
  • The drawers are perfect for sunglasses, mail, keys, and other small things
  • The cubbies are perfect for baskets, shoes, accessories, or books
  • The table height is perfect for hanging a mirror over top to create a beautiful entryway

 

Wood Console Table with Drawers Plans

Dimensions
woodworking plan for wood console with drawers
30" Tall x 42" Wide x 13" Deep. This console table is standard table height.

Preparation

Shopping List
  • 2 - 1x4 @ 8 feet long
  • 1 - 1x12 @ 8 feet long
  • 1 - 1x12 @ 12 feet long
  • 2 - 1x2 @ 8 feet long
  • 1/2 Sheet of 1/4" plywood
  • 2 sets of 10" drawer slides (Amazon 2 pack for $11 affiliate link)
  • 2 - Knobs
Common Materials
2 inch screws
2 inch finish nails
120 grit sandpaper
primer
wood conditioner
paint
paint brush
Cut List
  • 2 - 1x12 @ 29 1/4" (Sides)
  • 1 - 1x12 @ 41 1/2" (Top)
  • 1 - 1x12 @ 36" (Bottom Shelf)
  • 1 - 1x12 @ 25 3/4" (Center Divider)
  • 2 - 1x12 @ 17 5/8" (Shelves)
  • 1 - 1/4" Plywood @ 37 1/2" x 30" (Back)
  • 2 - 1x4 @ 11 1/4" (Drawer Slide Spacers - Cut to width of 1x12s)
  • 1 - 1x4 @ 37 1/2" (Footer Front)
  • 2 - 1x2 @ 24 1/4" (Side Trim)
  • 1 - 1x2 @ 37 1/2" (Top Trim)
  • 1 - 1x2 @ 34 1/2" ( Center Trim)
  • 1 - 1x2 @ 41 1/2" (Top Front)
  • DRAWERS- Drawer cuts, see in plan
Tools
Tape Measure
Speed Square
Pencil
Safety Glasses
Hearing Protection
Kreg Jig
Drill
Circular Saw
Jigsaw
Brad Nailer
Power Sander
Level
Drill Bit Set
General Instructions

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!

Instructions

Step 1

I've included pocket holes in the diagrams for those of you with a Kreg Jig. You can also use countersunk screws with glue, or even finish nails, as this cabinet is fully framed. 

 
Start by marking the top underside 2" on each end.  This will be the top overhang.  Then attach the two sides to the top as shown above.

Step 2

Now the bottom shelf. It sits 2 3/4" from the bottom.

Step 3

Mark the placement of the center divider and attach in place.

Step 4

You will need a pocket hole jig to make these shelves fixed. But certainly, you could use shelf pins to make adjustable shelves. Here's a great tute on how you can use pegboard as a guide for drilling your shelf pin holes.

Step 5

Drill 3/4" pocket holes on bottoms of shelves and attach inside the cubby area with 1-1/4" pocket hole screws.

Step 6

These are for your drawer guides. Use either 1 1/4" screws or nails to attach to the sides as shown in the diagram.

Step 7

What really makes a cabinet like this one is the cutout footer. Use the diagram above to help you cut a pattern from the footer and attach. You can also start by attaching the footer, and then cut the footer out afterwards.

Step 8

Use 2" finish nails and wood glue to attach the side trim.

Step 9

Now the header. Attach to the center divider as well.

Step 10

And now the drawer trim. You will need to either use pocket holes from the back or 2" screws and glue from the sides, outside to secure trim in place.

Step 11

And finally the top front. Attach in place with glue and finish nails.

Step 12

You will need to build two drawer boxes as shown above. Build the drawer boxes and attach 1/4" plywood leftover to the bottom. Don't worry about the plywood falling off - the drawer slides will hold it on. Your drawers should be built to fit your cabinet. Be aware that lumber can differ in width AND thicknesses, so you should always build to the cabinet. Standard drawer slides require 1/2" clearance on each side of the drawer, so make your drawers 1" less than the overall interior opening - use the diagram above as a guide.

UPDATE: We recommend using 10" drawer sides and slides so there's no issue with the drawer face being inset.

Step 13

Install drawers into the cabinet as shown above with the drawer slides. Here's a tute on the type of slides you should use and also how I install a drawer.  Remember that the drawer box needs to sit 3/4" inset from the face frame to allow for the drawer faces (see next step).

Step 14

Cut your drawer faces to fit the openings, and center of the drawers. Attach with 1 1/4" finish nails (careful about the hardware locations) and glue. Then remove drawer and attach faces to drawer boxes with 1 1/4" screws from the inside.

Step 15

DRAWER SLIDE OPTION:

Use metal angle (about $5 for 4 feet) to support your drawer.  Then build the drawer so it fits inside the angle, but leave enough room for your drawer to slide easily.

Finishing Instructions
Preparation Instructions
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. 

It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
Help Improve This Plan

We apologize if there was an error in this plan. Please help us out and report any errors here.

Comments

ACraftyCauldron

Tue, 07/19/2011 - 06:01

Ana - I love this console but even more than that I LOVE that you talents are being recognized more and more every day! Congratulations on the book - can't wait to see it!

Ayana (not verified)

Wed, 07/27/2011 - 13:44

Love this plan. I need a table for the my stair wall. I didnt know you got a book deal!! CANT WAIT!!

Guest (not verified)

Wed, 03/28/2012 - 11:39

Hi Anna -

My husband and I are trying to build the Cyndi Console Table, but cannot find where to order the drawer sliders. Can you please help us out??

Jordanmc1

Wed, 02/11/2015 - 08:21

What wood are we using for the drawer faces? I see the instructions cut to fit but what lumber are people using? It looks like a 1 x 6?