DIY Bucket or Basket Shelf Display Stand

Submitted by Ana White on Fri, 11/27/2015 - 10:57
Difficulty
Beginner
| Print this plan

Build a stand to hold buckets, pails or baskets super easy and quick like store displays. Plans by ana-white.com

Hi everyone, hope you had a wonderful Thanksgiving! Ours was pretty quick as we had to travel 350 miles to a hockey tournament for Grace.

photo via Instagram

The roads were awful but we made it!

I'm a little sad that we are getting so close to Christmas, because that means our Handbuilt Holiday series will come to an end.

If you are new to the Handbuilt Holiday series, it's pretty simple.  Jaime from That's My Letter and I team up to get you a new gift plan each Friday in the weeks leading up to Christmas.  You can check out all the plans we've done so far (over the past few years) here.

I'm especially excited about today's project!!!  It is so darn simple.  But so effective and useful!

All else pails in comparision!

May I present the bucket shelf!

When my son turned one, a friend gifted him with some baby toys, but instead of gift wrap, she placed the toys in a bucket.  I was so suprised at how much our baby loved the bucket, and played with it.  Buckets are great for storing all sorts of things, from toys to produce to all things entryway and beyond!

This shelf designed for buckets (this bucket was used) is especially awesome because its so easy and inexpensive to build!  The frame is just 1x3 boards - that's all.  It doesn't get much cheaper or easier than this!

So you ready to make this?

Here's what to do -

- Go check out Jaime's build post with lots more photos and building tips

- Grab the free plans below (if this is the homepage you'll need to click READ MORE below)

Enjoy the plans!

Ana

 

CLICK HERE TO READ JAIME'S BUILD POST ON THIS BUCKET SHELF

 

 

Fits nine Behrens 10 quart metal pails, approximately 3 feet wide, 14" deep and 3 feet tall

Preparation

Shopping List

6 - 1x3 @ 8 feet long

Recommend 1-1/4" pocket hole screws but 2" spax screws could be used

1-1/4" brad nails, staples or screws for attaching the front and back panels together

9 buckets (we used these)

Common Materials
Cut List

10 - 1x3 @ 35" long 4 - 1x3 @ 14" long 2 - 1x3s scribed to fit for cross support

Tools
Tape Measure
Speed Square
Pencil
Safety Glasses
Hearing Protection
Kreg Jig
Miter Saw
Brad Nailer
General Instructions

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!

Instructions

Step 1

Build two of the frames, they are identical. Use a scrap piece of wood cut at 45 degrees or a speed square to help guid placing the boards at 45 degrees. Attach with 1-1/4" pocket hole screws or 2" self tapping wood screws. Use glue at all joints.

Step 2

Attach the two frames together with 1-1/4" nails, staples or screws and glue. Place scrap board over sides, mark angles, cut and attach for additional support.

Finishing Instructions
Preparation Instructions
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth.

It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
Help Improve This Plan

We apologize if there was an error in this plan. Please help us out and report any errors here.

Comments