Community Brag Posts

Becca Trunk

Submitted by Linda7 on Fri, 05/29/2015 - 13:39

I built this trunk for my grandson’s high school graduation, and filled it with a lot of things he might need as he begins his life in the U.S. Air Force. Here are a few hints:
• Build the top after you place the moulding around the top of the box so you can measure exactly how long and wide the top needs to be.
• Don’t forget to measure the width of the 1” x 6” boards; if they are not exactly 5 ½”, adjust the length of the vertical boards on the trunk top or it could be slightly too small.
• Because of the extra width the moulding creates around the perimeter of the box, use narrow utility hinges, piano hinges, or Beverly of bzhays used black decorative strap hinges from Amazon.com.
• I used black handles from Amazon.com: Reliable Hardware Company RH-0540BK-2-A Set of 2 Chest Handle, Black
• For a more finished top on the inside, I filled the holes with wood putty and sanded it smooth, then stained and polyed like the outside of the trunk. The kreg holes are still visible, but not too much.
• Before screwing the box together, I recommend finishing the inside surfaces first; cover the edges that will meet with painter’s tape so the glue will have bonding surfaces.

I love the rustic look most have used in their finishes, but since I used a traditional stained finish, I used the ideas from Justin of jeverette1 who covered the exposed plywood edges with scrap. Since I didn’t have that, I used corner moulding for the corners, and lattice strips to cover the top edges of the box. This gives the trunk a more finished look if you are not going for the rustic/distressed look. I notated below a week-long project - I spend a lot of time in the finishing and do so over several days. Others could certainly finish in a weekend.

I’d like to thank Ana for the wonderful plans, and Whitney of Shanty 2 Chic for the great step-by-steps. Also, a big thank you to Beverly of bzhays and Justin of jeverette1 for responding to me with my questions; you were both so helpful.

Built from Plan(s)
Estimated Cost
$150.00 - I used better pine and stain-grade burch plywood to avoid hours of sanding.
Estimated Time Investment
Week Long Project (20 Hours or More)
Finish Used
Stain: Rusteoleum “classic cherry”; one coat and it took every drop of the small can. Finish: Minwax wipe-on poly, one can is enough for several coats. The pictures were taken at night with a flash, so it appears much shinier than it really is, plus the color is off too - not as "orange-ish" as it appears. I also had to paint the sash lock black (couldn't find any in black) and the piano hinge. The decorative tacks were found at Lowe's in the hardware section among the nails and they come in several finishes.
Recommended Skill Level
Beginner

Carrots Included

Submitted by hoffer5353 on Sun, 12/24/2017 - 07:16

Adorable gift ready for Christmas!

Built from Plan(s)
Estimated Cost
This project was less than $10 because I used hardware and scraps in my shop.
Estimated Time Investment
Afternoon Project (3-6 Hours)
Finish Used
Minwax Express Colors
Spray Paint
Recommended Skill Level
Beginner

Farmhouse Doll Bed

Submitted by jkjackson on Thu, 12/23/2021 - 19:39

Created from scraps using Ana’s plans for the bed and the mattress.

Comments

jkjackson

Fri, 12/24/2021 - 14:33

Thanks for the great plans and making the mattress so simple (for those of us who feel like just threading a sewing machine is like playing the game Mouse Trap while under the influence! 😄)

Our Farmhouse Table, Bench and Bar Stools

Our kitchen has been pretty much the same for the last 4 1/2 years but this last fall we started to undertake a huge do-it-yourself remodel. We painted our cabinets, replaced the sink and floors and even painted the counter tops! You can check out the transformation on our blog.

Now that our kitchen was looking so good we decided we needed some awesome furniture to match.

This is where the great Ana White and her wonderful blog stepped in. We were able to build some beautiful high quality furniture at an awesome price! This was the first time I actually had matching and completed furniture in my kitchen and I have loved it.

We built the farmhouse table, bench and the extra tall bar stools with some modifications.

Estimated Cost
We spent around $220 for all of the furniture.
Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
I used a wood conditioner, 2 coats of a Jacobean colored stain and two coats of a satin finish polyurethane.
Recommended Skill Level
Beginner

Turnings

Submitted by Russell AP on Sat, 06/22/2013 - 21:30

These are a few of my turnings. They are available for sale. Message or comment for price and shipping.

Estimated Cost
100$
Estimated Time Investment
Week Long Project (20 Hours or More)
Finish Used
Most of my finishes for turnings are Arm-R-Seal poly.
Recommended Skill Level
Advanced

Farmhouse nightstand

Submitted by mgibson on Tue, 06/02/2015 - 13:30

This project was very fun, and it was my first nightstand. The directions are so easy to follow. Thanks Ana : )

Built from Plan(s)
Estimated Time Investment
Weekend Project (10-20 Hours)
Recommended Skill Level
Beginner

Comments

Faux Fireplace Mantle

Submitted by KristineF on Thu, 12/28/2017 - 08:15

Thank you for providing the plans to this mantle. I had a lot of fun building it with my father while I was training for the NYC Marathon. We finished it the day before the race and was a great way to display both of my accomplishments! It was also a lot of fun to decorate for the holidays. Next I have to build a nice shelf to display all of my finisher medals! 

Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
Distant Gray paint with satin finish.
Recommended Skill Level
Beginner

Comments

Seasonal And Holiday

You chest

Submitted by Anonymous (not verified) on Sun, 12/26/2021 - 12:56

Ana White’s plans are the best I’ve seen. Some are easy and some are challenging builds. She’s so very encouraging in her videos. She makes me feel like I can keep on building. I’m very happy to say I started my business from her inspirations.

Built from Plan(s)

Comments

Tryde Coffee Table

I built Ana's Tryde Coffee Table.  Building was quick and easy and I am in LOVE with my new table!!!   You can see the modifications I made at our blog http://www.shanty-2-chic.com/2011/04/coffee-table-reveal.html

Built from Plan(s)
Estimated Cost
$40
Estimated Time Investment
Afternoon Project (3-6 Hours)
Finish Used
Minwax Dark Walnut and Rust-oleum Heirloom White Spray Paint
Recommended Skill Level
Intermediate

Nick & Leah's Farmhouse Bed

This was our first project & we worked on it together. My husband melded the Farmhouse plan with the Chunky Leg bed box. The box is reinforced & has 13 slats. We didn't sand out areas that had bark, but left them for the texture. We worked on it a few hours each night & then painted on Saturday & puit it together on Sunday. Design-wise we raised the bed so that the bottom of the frame sits at 12 inches. We also raised the footboard above the mattress level. These changes were just our preference, but we really love how it turned out. It is sturdy, substantial & beautiful!

Estimated Cost
$250.
Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
Valspar Signature Eggshell finish in Vanilla Steam. After sanding we only applied one real coat, but applied it liberally.
Recommended Skill Level
Beginner

Simple Stackable Compost Bin from Pallets Collars

Submitted by mtairymd on Sat, 06/06/2015 - 13:48

Build Instructions:
http://www.instructables.com/id/Simple-Stackable-Compost-Bin-from-Palle…

How it works:
https://www.youtube.com/watch?v=Tgtd88kKIn0

With one single unit as opposed to two or three bins, the space needed for composting is minimized. Each tier stacks on top of the other, latching together to make the bin. This setup makes it easy to turn and rotate the compost, since moving the collars is simple. Just remove the top collar and place in a new location adjacent to the original bin location. Turn the compost into the new location and stack the collars until finished. This is a great alternative to having multiple compost bins next to each other.

Estimated Cost
Free
Estimated Time Investment
An Hour or Two (0-2 Hours)
Finish Used
Cabernet colored stain from Varathane and a polyurethane from Minwax.
Recommended Skill Level
Beginner

Table for barbecue

Submitted by Pjc6 on Sat, 12/30/2017 - 11:38

Modified plans to make it a little larger. Top is brown and bottom is ‘wild currant’ (red)

Estimated Cost
$80
Estimated Time Investment
Day Project (6-9 Hours)
Finish Used
Top was Olympic paint / sealant. Bottom was SW enamel acrylic
Recommended Skill Level
Intermediate

Coffee cart

Submitted by Anonymous (not verified) on Sun, 12/26/2021 - 14:47

My husband built this a few years ago to free up counter space in our tiny kitchen and we just love it.

Comments

Footbridge

Submitted by sooz122 on Tue, 04/26/2011 - 18:36

I wanted to make a footbridge for my mom so she wouldn't get muddy when she crosses a small drainage ditch when goes walking on the trails behind her house. I didn't have a plan and this was my first build and I loved it! I just wanted to give everyone an idea of something to build. Can't wait to build more.

Estimated Cost
45
Estimated Time Investment
Afternoon Project (3-6 Hours)
Finish Used
Dark Minwax Walnut with a couple coats of poly.
Recommended Skill Level
Beginner

Sawhorse Table

Submitted by Alark on Wed, 06/26/2013 - 06:32

New table for our patio space. This was a fun, relatively easy project. The weather was my only hiccup in the building. Spent an afternoon making cuts, the next day sanding and staining and then assembly. Hubby saw the pieces laid out before staining was complete and loved the two tone look, so I went with it. I used minwax Kona for the stained area and covered everything with Spar Varnish.

Built from Plan(s)
Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
Minwax stain - Kona,
Spar Varnish
Recommended Skill Level
Intermediate

Comments

Table and Chair for my Daughter "Hannah"

Submitted by toddh5902 on Wed, 06/10/2015 - 07:18

Such great and easy to follow plans. Even for a beginner like me. I did both projects in stages at my own pace and time. It probably could have been finished in a weekend, if I worked steady and straight through. Also if you are good and know exactly what you are doing, definitely in a weekend(haha). I just took my time and worked in baby steps, working through both plans. I am very pleased with the outcome. I did change a few things but that was my preference. I attempted to contour the chair seat, not bad but definitely not great. I used a handheld grinder with about 60 grit sandpaper to make the mold. If you are good and have a very very steady hand this can work. I have a router but not a jig for that type of pattern. All in all though I was very pleased with the outcome and so was my little Hannah. Thanks for this great website and keep up the great ideas.

Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
No finish used yet at this time.
Recommended Skill Level
Beginner

Rustic table

Submitted by jdawn1988 on Mon, 01/01/2018 - 16:05

We built our table from the rustic table plans and I am in love. I am a beginner and I was so scared but it turned out amazing!! Thank you for giving me the courage and confidence to start building my own furniture! 

Built from Plan(s)
Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
Minwax stain in slate
Minwax polycrylic
Recommended Skill Level
Beginner

Nightstand 3 different ways

Submitted by Anonymous (not verified) on Sun, 12/26/2021 - 15:38

We took this plan and modified it a bit. The first photo is as a nightstand. We resized the red cabinet, made it deeper and a little wider, gave it a contrasting finish of chestnut stain on the drawer fronts and barn red on the body to make my sewing storage/desk (2 cabinets with a hollow core door on top). The green cabinet is higher and wider, with a cabinet at the bottom. This is used in our stained glass shop at a Renaissance Festival in a remote area, which is powered by hidden solar. The drawers house my paperwork and sales tools and a solar inverter in the open back cabinet at the bottom.

Built from Plan(s)

Comments

Outdoor Pine Canopy Daybed

Submitted by evilmom on Sun, 05/01/2011 - 14:01

This is my first venture into woodworking/carpentry. Since I did not want to shell out too much money for lumber, I used untreated pine (worst wood they say to use) for the daybed and used an exterior wood stain (with uv protection) to seal the wood. I also did not invest in power tools and used a hammer and wood saw to cut and nail everything together. As I cannot sew, I waterproofed the mattress by sandwiching it between two plastic mattress covers (dollar store) and duct taping the seams. It's not elegant but no one is going to see it. I used a cotton fitted twin sheet (old one) for the cover and found some outdoor pillows for $16 a pair ($8 per pillow and made with solarium fabric). Also as this is placed outside (deck), I'm looking into getting a mosquito net to use over the daybed instead of the bed tent I have on right now.

In hindsight, I should have used pressure treated wood for the posts and canopy beams to prevent bending/twisting (I had to re-do 2 posts). If I get 3 years of use for this furniture. I'm a happy camper. Ana, thank you so much for the plan. Kathy thanks for the advice on painting the lumber first.

You guys can do this!

Estimated Cost
$70 for the lumber, $ 40 for stain, sand paper, nails, wood glue, $4 for mattress cover, duct tape
Estimated Time Investment
Week Long Project (20 Hours or More)
Finish Used
Olympic exterior wood stain with UV protection (oil based).
Recommended Skill Level
Intermediate

Natural Finish Cedar Planter

Submitted by benpryor82 on Mon, 06/15/2015 - 07:15

Great results from this plan. The additional mitered top is easy as long as you can get a good 45 degrees on your saw. If you decide to do the top piece, glue the 4 mitered pieces together and clamp for a couple of hours in order to make sure the angles set correctly. Once the glue is dry, then attach to the top of your planter with glue and nails. I built 2 planters, including the mitered top edges, in about 5 hours.

Built from Plan(s)
Estimated Cost
Less than $50 for two planters.
Estimated Time Investment
Afternoon Project (3-6 Hours)
Finish Used
Unfinished, but will likely seal with Thompson's
Recommended Skill Level
Beginner

Letter A shelf

Submitted by Knathu121 on Fri, 01/05/2018 - 20:14

I made this Letter A shelf for my daughters nursery with scrap wood I had.

Built from Plan(s)
Estimated Cost
Under $10 due to the fact that I only need to buy screws.
Estimated Time Investment
An Hour or Two (0-2 Hours)
Finish Used
Spray painted white and then lightly spray painted pink.
Recommended Skill Level
Beginner