Community Brag Posts

entry locker

Entryway locker cubbies, top portion constructed in custom width and shelf height. Two sets.

Built from Plan(s)
Estimated Cost
$75
Estimated Time Investment
Day Project (6-9 Hours)
Finish Used
1. Primed
2. Two coats semi gloss white
Recommended Skill Level
Beginner

Comments

Lisette Coffee Table

My friend "Lisette" asked for a small modern coffee table. For her small studio apartment. So I came up with this modern-ish table. Made of 2x2's and a 20"x40" glass top.I found it on the side of the road with a FREE sign on it in Pacific Beach. Oh how I love beach people and all the free stuff they leave around :)

Estimated Time Investment
Afternoon Project (3-6 Hours)
Finish Used
Minwax Chestnut Stain (3 coats) and semigloss poly spray (5 light coats)
Recommended Skill Level
Starter Project

My first dining table

I built this table using modified pocket hole plans and a mix of pine, spruce and cedar lumber.

When I laminated the boards together to the table top I also applied four culls to try to keep it flat as possible. When I removed the culls the boards weren't as even as I had wanted so I used a belt sander with a 120 grit to take out the high spots. I filled the knot holes with some 5 minute epoxy and I really liked the look. I would use decent epoxy if I do another large lamination of knottty wood as the $5 microtube I bought was thick and hand to work into the small voids around the knots. After the epoxy cured for 12 hours I gently used the belt sander gentle to remove the excess and then gave the entire table top a little 220 grit action. 

 

 

Estimated Cost
This project cost around $300 in materials and took about 24 hours spread over a couple weekends to complete. The cost of the Kreg K4 jig isn't included in that price, but it will come in handy for the next few years.
Estimated Time Investment
Week Long Project (20 Hours or More)
Finish Used
I applied two coats of Minwax Fruitwood stain before topcoating with 4 coats of a 4:1  mixture of Helmsman Spar Urethane/Paint Thinnner. I gently sanded with 220 grit and then polished with a clean cloth between coats of the Helmsman. The Wood Whisperer from YouTube has some really helpful tips to get a smooth finish like diluting your finish and applying it with a clean cloth which has been moistened with paint thinner. I recommend checking out his channel.
Recommended Skill Level
Beginner

Adjusted design to fit smaller kitchen.

Submitted by Anonymous (not verified) on Mon, 01/21/2019 - 12:05

I left off the ends to fit a smaller kitchen.

Estimated Time Investment
Week Long Project (20 Hours or More)
Finish Used
Espresso stain with a triple thick polyurethane
Recommended Skill Level
Intermediate

Built-in bench with drawers, side cabinets and floating shelves

Submitted by Anonymous (not verified) on Sat, 11/26/2022 - 05:37

I have wanted a built-in window seat on this wall for a very long time. My hubby and I finally tackled this project. Definitely not perfect and lotsa challenges and mistakes made but we are happy with outcome.

Comments

Outdoor Sectional- The Great Outdoors

I can't thank Ana enough for her plans on this project. We recently purchased a big project house that was going to need a lot of work (and a lot of money.) That's why I was thrilled to find Ana's plans for the exact West Elm Wood Slat Sectional I was eying for my screened in porch. The exact configuration at West Elm would have cost $2130, but I built it and sewed all the cushions for just $288! Ana's sewing plan was really helpful too, but I altered mine to include zippers in the back to remove the fabric for washing, and ties to hold the cushions securely to the sectional. We finished the sectional with super easy india ink and poly for a deep black finish that still shows the wood grain. The screened in porch is now our favorite room in the house! Thanks Ana!

Estimated Cost
$288 with all cushions and pillows
Estimated Time Investment
Week Long Project (20 Hours or More)
Finish Used
India Ink- Found in art supplies stores this thin, watery ink goes on with a sponge brush and soaks completely into the wood leaving a deep, dark wood finish that still shows the wood grain. No need to worry about drips or evenness, this finish goes on in one coat and is super easy, especially on a tricky, large piece like this. Topped with 3 coats of water based poly.
Recommended Skill Level
Intermediate

Comments

JES

Mon, 09/05/2011 - 11:05

This looks really super! I clicked on your blog link and read a few entries (funny!) You did a great job! Love the fabric for the cushions too. How much India ink did it take to stain a piece this big? Did it take a long time to dry? cheers!
J

Historic Palouse Halltree

Submitted by Anonymous (not verified) on Sat, 01/26/2019 - 09:33

This piece was inspired by Ana’s plans and built as a collaborative project with my son.  The stock was all salvaged from a century+ old railroad depot on the University of Idaho campus that was marked for demolition.  The green and cream boards were the ceiling of the depot, and the unfinished stock came from the flooring, which was 1” tongue and groove red fir.  The first agricultural crops, forest products, and settlers of the region (North Idaho, Eastern Washington) flowed through that terminal.  This piece, therefore, is iconic of the regikn’s rough-hewn beginnings and stands as a reminder of its important past.

Estimated Cost
$60 for glue, hinges, screws, polyurethane. The wood was salvaged for free.
Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
After sanding the bare wood and scrubbing the painted surfaces, I sprayed a satin polyurethane (good ol’ rattle can!)
Recommended Skill Level
Intermediate

Farmhouse Bed (hybrid)

Submitted by Anonymous (not verified) on Wed, 12/07/2022 - 11:45

This is my first time building anything! I had so much fun and it was actually easier than I anticipated. I used the Farmhouse Bed (queen) plan as the basis for my design, but made a couple of tweaks. I wanted the planks in the headboard and footboard to be horizontally oriented instead of vertical. In addition, I bought some hardware for the side rails to hook into my bed posts so that I could easily assemble and disassemble the bed. I went to a lumber mill to select my wood and the worker convinced me to use red oak to build the project, due to the cost and the durability. I stained it with a white wash which I added a sage green tint to so that I could mute the red in the oak a bit. I wasn't able to buy the exact dimensions of lumber noted in the plans so I had to improvise. For example, they didn't have 4x4s so I glued 3 boards together to make my posts. By the time I sanded, the pieces blended beautifully and you can't even tell that it is 3 separate pieces of lumber. I built this bed for our guest room and I can't wait to have guests over!

Built from Plan(s)

Comments

Time Out Bench

Submitted by VelvetSky on Fri, 09/09/2011 - 07:19

I built this from wood scraps. I saw one at Walmart online but thought it was too small. I built this to suit my tall toddler.

Built from Plan(s)
Estimated Cost
$20.00
Estimated Time Investment
Afternoon Project (3-6 Hours)
Finish Used
General Finish Gel Stain Java

Decopauged 'Time Out'
Recommended Skill Level
Beginner

Comments

Benchwright Dining Table

I built this table using a hybrid approach; I used Ana's plans as a loose guideline (leg angles) and drafted the rest using the dimensions supplied at Pottery Barn's website (for the fixed table, not the extendable version).

Estimated Cost
150.00
Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
The table is finished in an Espresso stain with a clearcoat of Minwax oil-modified water-based clear satin polyeurethane. I beefed up the table legs by using "4x"6 lumber and also included a wood stretcher instead of a metal one. I originally installed a "3/4 metal stretcher made of spray-painted conduit, but it looked too flimsy and dinky when juxtaposed with the thick legs of the table. I added two countersunk lag screws to each endcap and also attached the stretcher with two lag screws and joist supports (all spray painted with Rustoleum textured black enamel). My favorite part of the table is the faux slotted cross-brace ends that protrude from each leg. I simply cut four "1 pieces of "1x"4 scrap and attached one to each leg using glue, two nails, and a nail set. Pottery Barn charges $999.00 for this table; I built it for $150.00.
Recommended Skill Level
Beginner

Comments

Keri Beth (not verified)

Wed, 09/14/2011 - 23:04

This is awesome. I'm finishing up my first project (floor to ceiling bookcases) and looking for a dining room table to make next. This just might be the one. Thanks for sharing!

Birthday Farmhouse Queen sized Bed

Submitted by ksmith311 on Sun, 09/29/2013 - 12:41

We built this bed way back in April for my birthday, but hadn't gotten the bedding quite right until now. We love this thing and it is sooo sturdy. I wish I would have taken more time on finish work to get the paint just right. I will probably repaint it in the future but for now it is a beautiful and necessary addition to our bedroom.

Thanks so much for the plans Ana, this was our first furniture project besides shelves and boxes. It definitely gave us the confidence to continue building and even to start creating our own plans and furniture designs.

** updated photos on 11/21

Built from Plan(s)
Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
Antique white paint in semi-gloss and distressed with Early American Stain.
Recommended Skill Level
Starter Project

Saw Horse Inspired Coffee table

Submitted by Nathan O on Tue, 12/15/2015 - 18:01

I essentially followed the Rogue Engineer plans exactly with the exception of making the table on 50 inches long to help it fit better in my living space. I also opted to not add the lower support struts that would be perpendicular to the table top. I felt like that were bulky and were necessary for support. I may choose to go back and add them though. A miter saw and Kreg Jig are essential to get this project done with ease. I gave it a rough sanding to help keep the rugged texture of the original woodand maintain the reclaimed look. Feel free to post any questions.

Built from Plan(s)
Estimated Cost
$30-$50
Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
Mini Wax Dark Walnut and Poly
Recommended Skill Level
Beginner

Desk

Submitted by Anonymous (not verified) on Sun, 01/01/2023 - 09:51

I'm so thankful for ana white. Without your ease of plans that you make easy for us, has inspired me with confidence to take on many projects. Thank you for the wisdom you share.

Built from Plan(s)

Comments

Pantry Storage Spice Rack

Submitted by redhead_61 on Mon, 09/19/2011 - 21:49

I am kind of a visual organizational neat freak and I have been annoyed by all the little things taking up good shelf space in my pantry for a long time now. This just kept getting pushed down the list ya know, not a major project. Anyway, grabbed an extra board at the store the other day and knocked this one out. I LOVE it. I made it short because I want to build a trash bag holder for the bottom half of the door. We'll see how long it takes me. I did use a 1x4 instead of Ana's plan which uses a 1x6. I only needed small things to put in here.

Built from Plan(s)
Estimated Cost
$5
Estimated Time Investment
An Hour or Two (0-2 Hours)
Finish Used
White Paint
Recommended Skill Level
Starter Project

Comments

SingleMomThriving

Tue, 09/20/2011 - 10:04

Looks like the 1x4 was a perfect fit for all those little items, especially the wraps which get pushed to the back all the time and the pasta boxes. I feel some inspiration coming on.....

lianatempera

Tue, 09/20/2011 - 14:16

This is awesome. I should probably do this for my pantry, as well. Thanks for the inspiration!

Cindy from Indiana (not verified)

Wed, 09/21/2011 - 09:31

I love it! Great price,too!

I especially love how the design corals all those pesky little things that always seem to get pushed all the way to the back of my cabinets and drawers.

I'm definitely putting this on my list of things to build!

Cindy from Indiana

Jen Pedro

Wed, 09/21/2011 - 13:34

I assume your door is the usual hollow pantry door. What type of anchors did you use to hold the shelves in place? Did you use standard wall anchors with your screws?

Looks great!

redhead_61

Thu, 09/22/2011 - 08:19

I just got an anchor that looked like it had a little more 'umph' to it. It is called a Cobra Tripple Grip. It looked like it had a section that popped open a little more once the screw went in. I thought that might hold it a little more securely. I feel no movement when I jiggle it at all.

Chris A (not verified)

Sun, 01/15/2012 - 08:29

Very nice project.
Just came along looking for a storage shelf and I saw your door shelf. Going to build one of these for sure, sick of the little wire ones we have falling down every other day.

Taylors console

We needed TV and game system storage for our vacation cabin and didn't want to spend a lot. This is perfect!

Built from Plan(s)
Estimated Cost
$80
Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
Used a mixture of some old darker stains I had on hand over the bare wood, then some Vaseline on edges I wanted to distress. Painted with DIY chalk paint (approx 1 teaspoon of unsanded grout mixed with a little water, stirred into 1 cup of latex paint.) Distressed with sander, then finished with two coats of wax.
Recommended Skill Level
Beginner

Square Farmhouse Table

Submitted by 42jbmayer on Sat, 12/19/2015 - 21:25

This is a square farmhouse table I built for my dining room.  It is just under 5ftx5ft size.  The top is 6 planks that I cut down from 2x12 down to 10inch sized planks.  Then routered each plank with a 1/8 roundover router bit.  I made the bench big and wide since I wanted it safe and stable so my toddlers don't fall off.  Lots of sanding since this is all kiln dried construction lumber.  I sprayed varathane poly, water based, and loved it.  I put 4 coats on of semi gloss, came out perfect.

Estimated Cost
250-300
Estimated Time Investment
Week Long Project (20 Hours or More)
Finish Used
Varathane Dark Walnut
Recommended Skill Level
Intermediate

Comments

Bench with foam padding

Submitted by Anonymous (not verified) on Mon, 02/11/2019 - 16:52

This was a fun little project. I made the bench to be placed in our foyer to sit down and put your shoes on and off. 3” foam and fabric makes for a comfy bench.

Estimated Cost
$100 ($60 lumber, $40 3” foam and fabric)
Estimated Time Investment
Afternoon Project (3-6 Hours)
Finish Used
White paint
Recommended Skill Level
Beginner