Community Brag Posts

This is my first project. I'm so happy with the results. We turned this potting bench into an outdoor bar. :)

I made this shelf quite some time ago. I changed quite a few aspects of it as I went a long and I am quite happy with the finished product. Thanks again to Ana for the rockin plans.

Had some leftover v groove planks from building a plank wall in son's room, so decided to make Ana White's cute Joy sign.  Had trouble finding a boxwood wreath that I liked, so ordered one from Home Depot.  It came in only 2 days.  Super simple and super cute.

This build was not hard, but just took time. The plans were perfect. Clear, easy to follow and correct. 

Materials cost about $400. 

This was a fun project because my 8 years old son got to help build his bed. I used a brad nailer to hold many pieces together after they were glued. Not a must, but it made the build a lot easier.  It also came in very handy when making the shelves.

We also added IKEA LED lights underneath the bed for a cool effect.  

I built this toybox for my son's first birthday. It took about a week to do, starting and stopping. I got Lowes to cut the plywood for me, and screwed everything together. Wood filler filled the countersunk holes, and a coat of primer and two coats of paint finished it off.

After everything dried, my wife added the name and crown in vinyl cut out using her Cricut.

My (excited!) first time building a piece for someone else. This table was made as a housewarming gift for some awesome friends. Many people contributed to material cost and my husband and I put it together.

The table is made out of all cedar to deal with the southern rain and sun (we haven't had a dry day since we delivered it a month ago, so you get a wet but sunny picture - yay hurricane season)

We modified the plans to incorporate two planter buckets for icing drinks and such. This required us to make two longitudinal frames instead of the one used in the original plans. We spaced the frames just enough to fit the planters down in them, then added short 1x2s between them to support the planters. Before boarding the top 2x6s together, I made rough cuts for the openings. When it was all together, my husband used a 2" router bit to clean up the edges of the holes.

Made the 8 foot FancyX benches to have as much seating room as possible for lots of friends and family. Looking forward to using it more when the weather dries up a little.

Ended up making mine 8x4 to fit between 2 windows on the side of the house. I put in a paver base and then built a 2x4 floor with three quarter inch plywood. 

I drew everything our first so I knew what to order from HD. I followed the plans basically but used 2x4s in the frame of the walls and back. I just used plywood on the back wall. We also can't get cedar fence planks in south Florida, only 6 ft pine pickets, so I made due. 

The roof I had to measure once the frame was up, just to be sure.  Also used a 2x6 as the cross brace on the front...wanted to make sure it was strong enough to prevent the doors from pulling in and sagging, since they're bigger. 

Tools:. Pocket hole jig is a must. And I did this completely solo, so air nailers were a 100% must. Frame nailer and Brad nailer with various size nails. I still may add angled brace 2x4 across the top interior to hold the square. Shingled the roof and added a little $9 solar powered light bulb, with a little panel wired to the roof. Works well. Still needs sealed and shingles trimmed but I get a lot of compliments on this thing. Turned out very impressive. 

Cost of everything.....around $400. Time, doing it solo seriously took like 3 days...probably about 25 hours for everything excluding paver base. 

This has been a project all summer and I was so excited to find that Ana had made a mantle. I had to make it bigger and I had so much fun making it! Thank you Ana!!!

This was my first table project. I needed additional desktop space in my home office. This table was easy to build.

This was my first attempt after finding the site. I was so happy with the ease of the plans and the way it turned out i made the dining table

My son asked me to build him a narrow desk for his bedroom, with lots of drawers. This desk is a modified version of the Brookstone desk, with 7 drawers on the side and a pull-out writing surface (inspired by the pull out surface LadyGoats added to the Mod bar wine grid base – Gina’s pictures from her blog were really helpful!) The top measures 16 ¾ x 48 (top is a 1x12 and 1x6 edge joined with pocket holes). Lots of pocket holes on this one, because it’s stained and I didn’t want to fill nail holes. For the color we were trying to match the PB small printers desk Chestnut color. The pulls are antique bronze from Lowes. The drawers slide directly on the wood, because I knew I wouldn’t have the patience to install 8 sets of drawer slides ;) used ¾” S4S and 1x2 to hold the drawers. The drawer bottoms and the wood all got a coat of soft wax, and they slide nice and smooth. This took about 20 hours to build and finish over a long weekend. My son said he thought it looks amazing, which is the best part!

I needed a place to store towels and other items in my bathroom. This was the perfect project for this. I have friends begging me to make one for them. Not too hard and it definitely does the job!

I built this table from your Farmhouse table plans for my friends.  They did the fabulous job of staining it.

Great site!

I loved the look of the farmhouse table, but it was a little long for what I needed as our kitchen table. The original plan made a longer dining room type table. I decided to shorten it up a bit, it has a bit more of a stocky look to it but we love it! It is such a solid design, and we get such great compliments on it. I used wooden dowels to fill the screw holes which gave it a bit more country look to it because the vinegar stain turned them a slightly different color than the tabletop.