Raised Planter Box with Bottom Shelf

Submitted by tracysmith on Mon, 03/29/2021 - 18:05
Difficulty
Intermediate
| Print this plan

Free plans to build your own raised planter with bottom shelf.  Plans created by Tracy Smith

raised wood planter box

Please, if you build this, use common sense. Always check for squareness after each step and if your planting methods require something different, the adjust these plans accordingly. Most of all, I hope you enjoy this! THIS PLAN HAS BEEN ADJUSTED AS PER COMMENTS MADE! :-) Thanks for the feedback so we can make the plans work! This is also one of the perils of not building it yourself first. Heheheh

As a member of both Ana's community and The Handyman Club of America, I get a lot of inspiration for my projects. I happened to find inspiration in the latest issue of Handy Magazine and the raised planter box that they feature. They do list the plans for the planter, however, it requires the use of special tools like a router table, chisels, and large pipe clamps. Those may not seem like "special" tools to some of you, but I don't have them so I'm labeling them special. :-) They used pocket hole joinery in their plans, but only in a small part. Why not use them everywhere and make life a bit simpler? I decided to take on the project myself and "re-write" the plans for our community.  Reader-submitted photo.

The inspiration piece is built out of cedar, if you use a different species of wood and plan to use this outside as intended, make sure you take steps to weatherproof your piece of furniture! :-)

Pin For Later!!

Raised Planter Box with Bottom Shelf

Dimensions
raised planter plans
50 1/2" W x 35 1/4" H x 21 1/2" D

Preparation

Shopping List
  • (4) 1 x 4 x 8' cedar boards
  • (1) 2 x 2 x 8' cedar boards
  • (1) 2 x 2 x 6' cedar board
  • (3) 2 x 4 x 8' cedar boards
  • (1) 1 x 12 x 8' cedar board
  • (1) 1 x 12 x 6' cedar board
Common Materials
2 inch screws
2 inch finish nails
120 grit sandpaper
primer
wood conditioner
Cut List
  • 4) 1 x 4 @ 34 1/2" (front and back box cladding) "A"
  • 9) 1 x 4 @ 20" (shelf slats) "B"
  • 2) 1 x 4 @ 21 1/2" (post caps) "C"
  • 4) 2 x 2 @ 34 1/2" (legs) "D"
  • 2) 1 x 12 @ 47 1/2" (front and back of box) "E"
  • 2) 1 x 12 @ 18 1/2" (sides of box) "F"
  • 2) 2 x 4 @ 46" (box supports & shelf supports) "G"
  • 2) 2 x 4 @ 47 1/2" (bottom shelf supports) "H"
  • 5) 2 x 4 @ 15 1/2" (box supports) "I"
Tools
Tape Measure
Speed Square
Pencil
Hammer
Safety Glasses
Hearing Protection
Kreg Jig
Drill
Circular Saw
Miter Saw
Brad Nailer
Power Sander
Drill Bit Set
General Instructions

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!

Instructions

Step 1

Make 2 of these panels and set them aside. Keep piece "E" flush to the front of the "D" pieces and attach using 1 1/4" pocket hole screws. Attach "H" 5" up from the bottom of "D" - so the bottom of the cross beam ("H") should be at the 5" mark from the bottom.

Step 2

Create the box supports using the diagram above, use pieces "G" & "I"

Step 3

Attach the box support to one of the panels making sure to leave a 3/4" gap between the box support and the 2x2 ("D") Use 2" screws through the face of the 2x4's

Step 4

Attach the other panel to the box support using glue and 2" screws through the face of the 2x4's

Step 5

Cut and attach end panels to finish end of planters.

Step 6

Measure 4" from the legs to start your slats making sure to leave an 1" gap between slats as you go across. Slats are "B" pieces

Step 7

Add pieces "A" to assembly

Step 8

Finally, add the post caps and you're done! To use, you'll need to either add plastic tubs for planting or you can put in a piece of 1/2" plywood and plastic lining.

Finishing Instructions
Preparation Instructions
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth.

It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.

Comments

In reply to by JHardaway (not verified)

tracysmith

Sun, 07/01/2012 - 00:53

Thank you for your question - it's how we all learn. The "face" of the board in this situation (and any other that I can think of ;}) mean the part of the board facing you. In between the boards that make up the bottom, you'll drive 2" screws in. It really doesn't matter where you place them but I tend to make sure they look even. Make sure you have enough screws in it to handle the weight of your plantings. So, if it were me, I would put at least one screw in each section to hold all the weight, or even two. It may be over kill to some people, but I'd rather do that then find it's not enough. I hope that answered your question. If not, let me know and I'll do what I can to get it answered! :-) Happy Building!!!

Dave Voss (not verified)

Sat, 07/21/2012 - 21:00

Tracy,

Did you use Google's 3D drawing program for your diagrams. They look good!

I don't see "A", "B", etc. labels on the diagrams. Are they missing or does my computer just not show them.

If they aren't supposed to be listed, how should I figure out which part on the parts list fits it's position on the diagrams?

Dave

fpliu

Fri, 04/10/2015 - 16:10

Just finished this. Looks great. I made the following additions. I stapled1/4 hardware cloth and some weed block cloth to the box frame. This holds all my soil and supports draining.

Free Plans Made Possible By Our Sponsors