Rolling Room Divider Cubbies

Submitted by Ana White on Thu, 03/18/2010 - 19:14
Difficulty
Intermediate
| Print this plan

Cubby shelves are so loved because they enable you to further divide down your storage spaces. This simple cubby was transformed by one of our amazing readers into this outstanding storage playroom.

Collections
I'm sure there is somewhere in your home you could roll this . . .
And quickly becoming one of my favorite colors is this "eggplantish" pink, with muted undertones. A little tip from someone who has painted tons of furniture, choose a color that is slightly muted. When you choose colors that are too bright, your furniture may take on a Dr. Seuss look. Nothing wrong with Dr. Seuss.
Ready to get your lumber cart and roll down the aisle, maybe get a few odd looks?
Dimensions
Overall Dimensions are shown above. Height without caster wheels is 60 1/2″. Depth is 13″ and width is 48″. Caster wheels will add approximately 2 1/2″ to the overall height. You can purchase different height caster wheels.

Preparation

Shopping List

10 – 1×2 Boards (pine boards are about $1 each)
5 – 1×12 Boards (pine boards are about $9 each) OR 2 Sheets of 3/4″ A1 Plywood or 3/4″ MDF
Wood Glue
Wood Filler
2″ Nails for finish nailer
1 1/4″ Nails for finish nailer
5 Caster Wheels, shown in diagrams with a 2 1/2″ diameter, with screws
Sand Paper
Paint, Stain, Varnish or other finishing supplies

Common Materials
Cut List

Cut List for the Box
2 – 1×12 @ 59 3/4″ (Sides)
4 – 1×12 @ 46 1/2″ (Shelves)
1 – 1×12 @ 48″ (Top)
8 – 1×12 @ 14″ (Dividers)
Cut List of Trim (recommend to cut to measurements for exact fit)
4 – 1×2 @ 48″ (Top and Bottom Trim)
8 - 1×2 @ 57 1/2″ (Side Trim and Divider Trim)
18 – 1×2 @ 14″ (Shelf Trim)
3 – 1×2 @ 11 1/2″ (Wheel Supports)

Tools
Tape Measure
Speed Square
Pencil
Hammer
Safety Glasses
Hearing Protection
Kreg Jig
Drill
Circular Saw
General Instructions

Work on a clean level surface. Mark out joints prior to fastening. Take a square after each step to ensure your project is square. Use glue and 2″ nails unless otherwise directed. Wear saftey gear and take necessary safety precautions. If you are working with sheets of plywood or MDF, have your hardware store cut your plywood or MDF into strips that are 8′ long and 11 1/2″ wide. These will become dimensionally the same as a 1×12 board. If you are working with MDF, avoid nailing close to edges to avoid splitting your MDF whenever possible. You can alternately use drywall screws for MDF or wood screws for wood.

Instructions

Step 1

Composition for Paint or Rustic Stained Look is pine boards in 1×12 width for the “box” and pine 1×2 boards for the trim
Composition for “Framed in Solid Hardwood” Look is 3/4″ A1 plywood in choice of hardwood (ie Maple) cut into 1×12 strips (11 1/2″ wide) with hardwood 1x2s for the frame.
Composition for Economical Painted Finish is 3/4″ Particle Board or MDF cut into 11 1/2″ wide strips, framed in 1×2 MDF or pine boards.

Step 2

Build the box. Start by marking out the sides where the shelves will be fastened. It is a good practice to mark on both sides of the shelves to mark where to nail. Remember that the shelves are 3/4″ thick. Leave a 3/4″ gap under the bottom of the bottom shelf as shown above.

Step 3

Dividers. In this step we are just going to fasten the dividers in so they don’t move. The trim will actually hold the dividers in place. Start by marking your shelves and top where the dividers will go. Remember that the dividers are 3/4″ thick.
Starting on the bottom shelf, fasten the bottom dividers to the bottom and first shelf. Working your way up, fasten the next level of dividers in place. This time you will only be able to fasten through the shelf on the upper shelf. On the lower shelf, you will need to nail at an angle through the front edge of the shelf into the ends of the dividers. Do this on the remaining dividers. Use 2″ nails and glue. Remember, we will add more support in the frame to the dividers.

Step 4

Bottom and Top Trim. Check for square. Then using 2″ nails an glue, fasten the bottom and top trim in place. Make sure you fasten to any vertical dividers, whenever possible. Keep outside edges flush. Do this on the front and back.

Step 5

Step 6

Divider Trim. Measure and cut your divider trim. Mark the bottom and top trim boards as shown above. Fasten the divider trim to the dividers, as shown above. The trim will be centered on the dividers. Make sure you fasten to the shelves too. Use 2″ nails and glue. Do this on both the front and back.

Step 7

Shelf Trim. Measure and cut your shelf trim, keeping top edges flush with the tops of the shelves as you fasten the shelf trim in place. Use 2″ nails and glue. On the ends, fasten through the side trim into the ends of the shelf trim.

Step 8

Wheel Supports. As shown above, fasten the wheel supports to the bottom of the piece. Then attach your wheels to these support pieces.

Step 9

Finishing. Fill nail holes with wood filler and sand and finish as desired.

Help Improve This Plan

We apologize if there was an error in this plan. Please help us out and report any errors here.

Comments

team crane (not verified)

Fri, 07/01/2011 - 17:15

hey there! my husband built these shelves and also jigsawed these trees for me. we got the pattern here: http://www.diyideas.com/howto/WorkWithWood/plywood-tree_1.html

we printed it, projected it onto a piece of...hm, it's not plywood (it's thicker)....he traced it, and he needed to make several tries, to be honest...using a projector (we did ours in the garage where we could make it dark) makes it easy to make the trees the size you want...I wanted mine sizeable....

good luck!

Kristopherson (not verified)

Thu, 07/14/2011 - 14:37

Nice job on these shelves. Can you give me an idea of how you did the base? The trim looks slightly larger there--it is a good look...
Thanks!

Jessica Kennedy (not verified)

Wed, 06/27/2012 - 10:32

The link doesn't work. Could you please send me the pattern

Thanks

Guest (not verified)

Mon, 12/19/2011 - 08:13

First I would like to say I was thinking of making somehting like this and today I come across this article:) I love the tree cut outs but the link is not working for me can someone send them to me please...Thank You

jessica kennedy (not verified)

Wed, 06/27/2012 - 11:30

Please me too! Would love these trees

Mrs. Wags (not verified)

Wed, 01/11/2012 - 13:27

First time builder here. I would like to build this but turn the plan horizontal so my finished product is approximately 60" wide and 48" tall. The only thing I can't figure out is what thickness the shelves are. If I make this out of strictly pine it says the boards are 1"x2" but in the plans it says they are 3/4" thick. Help! Which is it?

claydowling

Wed, 01/11/2012 - 15:13

The dimensions of surfaced lumber are their rough-sawn thickness. Coming off the saw boards have a very rough surface. It's planed down to a more agreeable surface before it reaches you. Typically it looses 1/4" in thickness and about 1/2" in width.

If you have the material planed to order by the lumber yard, you can sometimes get it slightly thicker, but that's not worth doing unless you are ordering hardwoods. My lumber supplier was willing to go to 13/16", to leave me some room for final cleanup, but I did notice that some boards still have a bit of the rough surface that I'll need to take down on my own with a hand plane.

When you go to buy lumber, you should take a ruler or tape measure with you to check the actual thickness. Some places are selling 1x stock that is actually 5/8" in thickness. Don't buy from those stores. Sorry, don't know which ones are doing that, and I suspect that it's only isolated cases. But it's a warning sign that they aren't selling quality materials.

MCGBishop

Sat, 08/23/2014 - 11:57

Hi there! I'm really looking forward to making this, or a similar project for my mudroom. I noticed in the list of tools needed, it lists a Kreg Jig, but it is never mentioned in the directions. Is this only if you use screws instead of nails? And if so, you would use it instead of the angled nails?

jlharrison

Mon, 11/21/2016 - 06:33

Ok. I am a little confused. The expedit shelving is designed for the drona bins. They measure 13x13x15. So 1x12 would not be sufficient in making a shelf deep enough to accommodate these. I want to be able to utilize these bins in my closet. Any suggestions on those to work with out using plywood?! Can you buy 1x16 boards? I wasn't sure if that was possible!? I have seen edge glued ones at Menards but they are only 4ft and that won't work for this project?!

Help!!