Simple Sideboard with Open Shelves and Drawers

Submitted by Ana White on Mon, 05/17/2021 - 20:28
Difficulty
Intermediate
| Print this plan

Free plans to build your own simple sideboard from Ana-White.com  Features adjustable shelves and four drawers, detailed plans with diagrams, shopping and cut list.

white sideboard plans

My teenage daughter Grace has been asking for more storage in her bathroom for a couple years now.  If you wait long enough, they get old enough, and smart enough, to design it themselves .... yes, she did.  She went on Shelf Help, designed what she wanted, the pieces showed up in my shop, and then I built it:

It took me a day, working a few hours in the morning and most of the afternoon, to finish this project. It is quite big, and there's alot of drawers - which aren't hard, but do take time.

Where to Use This Sideboard

We used this project for storage in a bathroom, but it could be used in many different rooms in the home:

  • Sideboard in a dining room, store wine glasses, decorative serving ware, or baskets with dining linens
  • Entryway Console dropzone, empty shelves could hold shoes or baskets with accessories
  • Media Console in the living room to support a TV system
  • Dresser in a bedroom or closet, the open shelves could be used for folded clothing or shoes

Customizing the Size or Functions? 

This project is easy to customize in size!  Use our free Shelf Help Configurator to change up your carcass size in just a few clicks!

furniture design software

You can also change up what bay you put the drawers in, or do drawers only on the top row, and open shelves below.  This project is super easy to customize - it's all up to you and what you need!

Free Plans for this Sideboard

The plans for this sideboard follow.  Please share a photo if you build it, we'd love to see how your project turned out!

Dimensions
white sideboard dimensions
Dimensions shown in diagram

Preparation

Shopping List
  • 2 Sheets of 3/4" thick plywood and edge banding OR Shelf Help Carcass Kit
  • 1 sheet of 1/4" plywood for back and drawer bottoms
  • 5 - 1x4 @ 8 feet long
  • 1 - 1x2 @ 6 feet long
  • 1 - 1x8 @ 6 feet long
  • 1 - 1x6 @ 6 feet long
  • 1 - 1x12 @ 2 feet long
  • 4 sets of 14" full extension drawer slides (affiliate link to Amazon)
  • About 100 - 1-1/4" Pocket Hole Screws
  • 1-1/4" and 3/4" brad nails
  • wood glue
  • 4 knobs or pulls
  • primer and paint or desired wood finishing supplies
Cut List

Shelf Help Carcass Kit or 3/4" plywood panels, cut into pieces as noted below, front edge finished with edge banding

  • 1 - 3/4" plywood @ 15-1/4" x 72"
  • 2 - 3/4" plywood @ 15-1/4" x 35-1/4"
  • 1 - 3/4" plywood @ 15-1/4" x 70-1/2"
  • 2 - 3/4" plywood @ 15-1/4" x 31"

Carcass Trim

  • 2 - 1x4 @ 23" (bay supports, upper)
  • 2 - 1x4 @ 70-1/2" (bay supports, lower)
  • 3 - 1x2 @ 23" (drawer seperators)
  • 1 - 1/4" plywood @ 34" x 72" (cut 34" instead of 36" so you can get the drawer bottoms out of the scrap wood)

Drawers

  • 6 - 1x4 @ 14" (drawer sides)
  • 2 - 1x8 @ 14" (drawer sides)
  • 6 - 1x4 @ about 20-1/2" - measure and cut to fit (drawer front and back)
  • 2 - 1x8 @ about 20-1/2" - measure and cut to fit (drawer front and back)
  • 3 - 1x6 @ 22-3/4" - (drawer faces)
  • 1 - 1x12 @ 22-3/4" (drawer face)
  • 4 - 1/4" plywood @ 14" x 22" (drawer bottoms) - cut the back for the project first, and then cut the drawer bottoms from the leftover plywood
Tools
Tape Measure
Speed Square
Pencil
Safety Glasses
Kreg Jig
Drill
Circular Saw
Brad Nailer
Power Sander
Shelf Pin Jig

Instructions

Step 1

Build the carcass, starting from the sides attached to the top, then the bottom attached to the sides, and finally the dividers attached to the top and bottom.  The shelves can be made fixed or adjustable with shelf pin holes.

Use three 3/4" pocket holes and 1-1/4" pocket hole screws for each joint.

Step 2

Add bay supports along the top, and at the front and back of the bottom, with pocket holes hidden on the back side.  Use two 3/4" pocket holes on each end, and then pocket holes facing upward to further secure.

For the top bay supports, I found they made the space too small for the 14" drawer slides, so did not put a bay support in the center bay.  If you want drawers all across the top, use 12" drawer slides, and keep the bay supports all across the top.

Step 3

Attach 1x2 drawer trim as shown, with pocket holes on undersides.

Step 4

Install the drawer members of the drawer slides on the 14" drawer side pieces, so the drawer slide is centered of the drawer side.

Position the drawer side in the opening and mark approximately where the center of the drawer slide should be mounted inside the cabinet.  Also mark 7/8" in from the front.

Install the cabinet member of the drawer slide inside the cabinet.

Step 5

Measure in between the two drawer sides, and cut 1x boards to fit.  Drill two pocket holes on each end and attach to the drawer sides.

Step 6

Remove the drawers, measure the bottoms of the drawers, and cut the plywood bottoms to fit.  Attach with glue and 3/4" brad nails.

NOTE: Reserve back piece of plywood for back of cabinet.

Step 7

Cut the back piece for the cabinet.  If cutting at 34" to fit all the pieces on a single sheet, hold the back up from the floor.  Attach with glue and 3/4" brad nails.

TIP: Before attaching the back, mark with a pencil on the outside sides of the cabinet the location of the dividers.  Then you can pencil between your marks on the back when it is in place to know where to nail to.

Step 8

Attach the drawer faces to the front of the drawers with a couple of 1-1/4" brad nails.  Avoid location of hardware when nailing.

Pull the drawer open and further secure with a couple of pocket hole screws, used like regular screws here.  

Step 9

Drill holes for adjustable shelves (if desired) or install shelves fixed.

NOTE: I decided to cut 1" off the back of the shelves so they would sit inset and also not be in the way if I add doors later on.  This is optional.

Comments

mrseo

Thu, 05/20/2021 - 02:10

I am a new user of this site so here i saw multiple articles and posts posted by this site,I curious more interest in some of them hope you will give more information on this topics in your next articles. Airco op maat

mrseo

Thu, 05/20/2021 - 02:15

I really enjoyed reading this post, big fan. Keep up the good work andplease tell me when can you publish more articles or where can I read more on the subject? Zonnepanelen Eindhoven

mrseo

Thu, 05/20/2021 - 02:16

I just couldn't leave your website before telling you that I truly enjoyed the top quality info you present to your visitors? Will be back again frequently to check up on new posts. Airco 2021

mrseo

Thu, 05/20/2021 - 02:18

Hello! I just wish to give an enormous thumbs up for the nice info you've got right here on this post. I will probably be coming back to your weblog for more soon! Zonnepanelen Heeze-Leende

mrseo

Thu, 05/20/2021 - 02:20

This is a good post. This post gives truly quality information. I’m definitely going to look into it. Really very useful tips are provided here. Thank you so much. Keep up the good works Warmtepomp installatie

Free Plans Made Possible By Our Sponsors