Community Brag Posts
Little Helper Towers
Took the dimensions for the little helper towers and used the 24 inch width so it can accommodate two kids. Built two of these for my nephew, one for his house and one for my parents. Took 3 days of work, so I must not be as efficient as everyone else, but boy does he love them. Been eating all of his meals in his "tower" ever since he got them. Makes the effort worth it! One note: I couldn't get the pocket screws to work at all, ended up destroying a few pieces of wood which required an extra trip to the lumber yard. I would suggest just using counter bores.
Simple Outdoor Table
I was inspired by Handymommy's set, using the arm chairs instead of the standard ones, so thanks to you!
The wood I had was all rough cut 1 x 6's so I had to adjust the plans a bit.
Garden bed with folding screens
I added folding screens to my garden bed to prevent my dog to go in it. It can also discourage hares, cats and other animals. The folding screens make it easy to work in your garden.
Queen Storage Bed
I took a couple of ideas and made this queen size storage bed.
Carol Hicks
Rustic X Bench
Created the small easy rustic x bench, it was super easy to build even with all the small angles. Very good plans, the video was also nice to watch before getting started especially since I made mine 36" long and the handy tip on how to cut the cross braces helped. I also decided to use a 2x12 for the bench top as opposed to the 1x12 because it felt even more rustic to me.
Outdoor High Top Patio Set
I designed and built this "Caribbean Inspired" outdoor patio set based on the plans for the "Vintage Bar Stool". Once the stools were built, I designed the table to fit the height of the stools. The table top has stone mosaic tile and all surface are painted bright Caribbean colors. I do need to add the finishing touch of a cooler on the bottom shelf, but that's coming!
Rust Ole um clear lacquer spray finish (For sealing the paint & protection.)
14 person farmhouse table
My wife wanted to seat 14, so I basically doubled the plan with a few extra inches on each side. We also wanted umbrellas, so drilled holes where they would just meet. The stain is the Behr semi-transparent deck stain and sealer in Harbor grey.
Flatware Caddy
We camp a lot in our travel trailer and until now we’ve always used a coffee mug to move our utensil around and keep them easily accessible; the problem was, that coffee mug was constantly falling over! I saw this and knew I HAD to make one.
Made this with scrap 2x6 and 2x4 boards which cause the measurements to be a bit different, but the results were still great! Super easy and gonna be very useful!!!
Entryway Divider
Happy to share this completed project based on Ana White entry shelf with hooks plan. I have a place to land when I come in the door!
Modern Outdoor Sectional
Loved doing this as my first ever building project. Ana's plans made it easy and I found a tutorial for making the cushions at Sew Mama Sew. It's not perfect but we love it because it seats so many people comfortably and is exactly the right size for our patio. (All of our friends have complimented it like crazy, too!)
Comments
Thu, 07/26/2012 - 16:32
Spectacular!
You did such an awesome job on this. And it's your first project -- wow, it looks like it came right out of a furniture store and cost thousands! The piping on your cushions is a wonderful touch and it looks so flawless. Just beautiful!
Mon, 10/22/2012 - 08:15
Wow, this is really great. I
Wow, this is really great. I love that color - How did you do the stain/paint? Is it meant for outdoor use?
Outdoor Lounge Chair
Simple outdoor lounge chair for use on our deck. This is a good design though if I had to do it over again I would make a few alterations:
- It's a bit flimsy, so for the chair frame, I would use 2x4's instead of 1x's.
- We are going to use them for seating at our patio table so I will make the others a bit shorter. The depth is awfully big for a dining chair but would be good for lounging.
- Used a 1x4 on the inside of the back frame to make the chair back more upright (as it said in the modified plans) would definately recomend.
Farmouse
My first building project ever. Love it and plan on putting it in my dining eventually
Family Back Deck COVID19 Project Facelift
Thank-you so much Ana White! We took on our back deck as a family COVID19 “homeschool” two weekend project! Why just build a sectional sofa when you can build a sectional sofa, coffee table, farmhouse table with two benches, two Adirondack chairs and a side table that the 11 year old designed and built himself! Mission accomplished, he’s a builder for life.
Our deck was brutally neglected and the boys had had some exposure to power tools and small builds. We decided that the best way to remedy the situation was to set up a family build all at once so that the tools are out and then put back away after the build is complete!
The plans were easy to follow and incredible! Thanks again so very much!
Outdoor Chairs and Cedar Storage Chest
Ana White chairs along side my Ana White cedar storage chest (one of my 1st builds). Ana, thank you for the plans & for inspiring us to build!
Keith from Springdale, AR
Modified Trestle Table
This is the kitchen table that I made when my wife said I "wasn't handy", I'm pretty sure she meant she wanted me to replace the ceiling in the dining room...
I took the Farmhouse Table plans and changed them a bit to create a true trestle table. I'm pretty happy with the results.
Unfortunately there isn't anywhere to put the Google SketchUp of this project.
Comments
Tue, 07/31/2012 - 14:32
Is it possible to give
Is it possible to give details on the modifications you have done? This is the type of table I am looking for.
Wed, 09/05/2012 - 11:57
Changes
Basically I combined the farmhouse and trestle table plans that Ana has up here... I didn't want to use a metal bar to fasten the legs, so I used a wood cross brace. Though honestly with the large box legs, the table is very sturdy even without a cross brace. I have a Google SketchUp of this project if you want it.
Sun, 03/10/2013 - 14:09
I love it!!
Would it be possible to get your google
sketchUp of this table? Thanks!
Sun, 12/01/2013 - 20:05
I love the color of the
I love the color of the finish. I am just about ready to start building my farmhouse table and was looking for a nice color for the finish. Thanks for sharing!
Florida Cypress Truss Beam Farmhouse Table
Here's my take on the Truss Beam Farmhouse Table using native Florida Cypress which was cut to size from raw logs at a local cypress mill. Thanks so much for the inspiration and plans. My wife loves it and it looks great in our first home.
I finished it with Odies Oil and a combination of Odies Oil and Odies Butter for the table top to preserve the natural beauty of the wood while protecting it from food and liquids.
I probably spent $600 in all but I got a killer deal on the wood which should have cost around $800-$900. I would guess that if I were to try to buy a table like this one out of the same wood, it would have easily cost over $3,000.
Comments
In reply to Size by Jake'n'Leelo
Wed, 01/07/2015 - 08:05
SIZE
I modified both the tabletop and the base.
The final length of the top was about 69" (+ or - an inch or two). In the pics you'll notice the breadboard ends are half the original size. These pieces were pecky cypress and one of them was very pecky which would have made it difficult to join.
As for the base, because of how sturdy the table top joints are (pocket screws and wood glue) and the smaller breadboard ends, I decided it wouldn't matter if the table legs were directly bellow the breadboard end joints. I also preferred extra legroom clearance (tall people problems) so I made that the priority and adjusted the base for the desired legroom. Not sure the exact measurement but it looks like it was about 15" on each side. After almost a year of everyday use it seems that I was right, supper sturdy and going strong.
Thu, 08/06/2015 - 10:19
Breadboard design
Your table looks awesome. I am preparing to make this also and during my research I have found comments over the concern with attaching the breadboard ends. Instead of pocket holes, the true woodworking suggestions are to use mortise and tenon joints with gaps to allow for expansion and contraction a described here, http://goo.gl/Or5HJM. What method did you use and how is it holding up? My goal is to build a table that will last and that looks professionally made our as close to it as I can get.
Keepsake doll crib and highchair
We were trying to figure out what to give our granddaughter for Christmas when the great grandparents arrived with our 2 kids old maple crib from the 80's. After much debate(well, not really, apparently the crib now breaks every law in the book!) we decided to repurpose it into keepsakes. Enter Ana White! We settled on a doll crib and doll highchair. After many design changes trying to best utilize the old wood we came up with these. As you can see they were a hit and luckily very sturdy! There are now 2 doll cribs, 2 high chairs and 4 granddaughters, each family has a set as a keepsake. There are a few scraps left just in case a grandson happens along! Should be enough for a logging truck!
Picnic table
Got the plans on here had a little trouble with the angles on the seat but overall looks good and was easy to follow the plans
in screws
Kids Storage Bench
I created what I call the Kid Kave for our grandkids. I used the front entry bench plan to make a small sofa for under the loft. My best piece yet!
Comments
CUJO1366
Wed, 09/16/2015 - 21:44
gun cabinet
I would love the plans for this
Joshua_kubinski
Wed, 12/02/2015 - 20:47
Plans
I would love to get plans for this. I have been trying to come up with my own but I'm not very good at it. Thanks love your work.
Joshua
doyle.saylor
Wed, 12/14/2016 - 08:25
Plans
How can I get the plans for this?
doyle.saylor
Wed, 12/14/2016 - 08:27
Plans
How can I get the plans for this?
John Prom
Wed, 12/21/2016 - 12:33
Hi
Hi
jhouseholder
Wed, 12/09/2020 - 07:43
How do I get the plans for…
How do I get the plans for the gun cabinet?