Community Brag Posts

The craft table was based on the Modern Craft Table plans and heavily modified to be at regular seating height. We also added a pull-out iron table based on plans from Made by Marzipan. The pictures are kinda deceiving, but the ironing table does push all the way back in the table and it only juts out just to show it :) Check out our blog post for more:

http://tonyandkristine.blogspot.com/2013/03/diy-craft-table.html

I LOVED this plan for a cart.  I was looking for a cart to hold my heavy mixer and be able to roll in and out of my pantry. In addition to Ana's plans,  I enlisted my 3 sons to hammer the wood to make it look rustic.  Instead of aluminum angles, I used steel angles and I used a 36 inch height to accommodate more shelves. This is one SOLID cart.  I absolutely love it!  Thank you for the inspiration!

DIY Craft Desk.

I built this desk for my wife to give her more space to create her crafts. I meshed a couple designs that I had researched to give her a unique design. This project took me 1 week to complete by only working on it in the evenings but it could be done faster if you have more time available than I did!  

Materials Needed:
2 - 6 foot 1x4" pine or Poplar wood
1- 8 foot 1x4 pine or Poplar wood
4- 2x2" pine wood 29" long
2- 1x2" pine wood 24" long
1- 12"x48" pine board (pre cut craft wood in Lowe's)
1- 24"x 72" pine board (pre cut craft wood in Lowe's)
Box of 1 1/2" wood screws
Wood glue

Wood stain and/or paint 
8- 1" corner braces

1). Cut the 12"x48" craft board in half (2- 12"x24"boards.)This will be your shelves. Sand all of the wood prior to staining.
2.) Stain shelves and desk top. We used two coats of gray stain. Finish with one coat of Polyacrylic. Sand. Then one more coat of polyacrylic.
3.) Cut the 1"x2" trim to 2- 24" long strips.
4.) Attach the 2x2" posts to the 1x2" trim with wood glue and wood screws. You will end up with an upside down U shape. This trim piece will give added support for desk top. Do this twice and then Paint your posts.
5.) Mark where you want your shelves on the posts and screw in your corner braces to hold the shelves up. I placed the shelf inside the posts to give me 12" of width for baskets. Screw your braces onto your shelf and then attach to the posts. I recommend doing the bottom shelf first so it stabilizes the posts.
6.) Do the same thing with the top shelf. Mark where you want them and attach with corner braces.
7.) Moving on to the cross box base.... Build the 4 sides of the box first with the 1"x4" boards. This desk is 24" deep and 29" tall. Use wood glue and wood screws to assemble. I predrilled the holes then, placed glue on then screwed together.
8.) Make sure your top 1x4" is the full depth of the desk so the weight of the desk top is spread evenly on box.
9.) I used this guide for the interior cross pieces. http://sawdustgirl.com/x-leg-office-desk/#aa
10.) Paint your cross base.
11.) Attach desk top to bases with wood glue and wood screws and you are all set!

It was a fun project! - Jen

I found the plans for this bed on this site and was sooooo happy. i was looking for a unique bed for my daughter. I had searched beds for girls and cam across castle beds. I found some pretty extravagant beds costing $20,000 by personal designers and then I found beds from $1,000 to $5,000 buy it and put it together and THEN I found this plan. People asked me if I had experience in building anything. The answer was no BUT I CAN do it!. Plus the plans were very easy to read and understand! My daughter is beyond excited! She can hardly contain herself! THANK YOU!

Our kids love our new library!  We have lots of books but few places to store them (one grandma is a reading teacher and the other works in a library).

Our alcove is 11' wide and the long shelves are 10' long.  The short shelves are 2' long.  The antique church pew in the center is 5' wide.  I put the bottom shelves just below the outlets so we have an iPad charging station.

I built this project 8x10 and made the back wall exactly like the front wall and just added diy windows for air circulation. I live in the desert so I did not use clear panels I used white panels for sides and top and tinted panels for front and back so that my plants would not get scorched. I am running a hydroponic system and could not be happier with the results for a first time gardener! I built it completely by myself in about a month, I do have a full time job and kids that need to be taken to practice and lessons after school.

Well...this was pretty much all done by me.

I am really not liking how many bad boards there are at the store. It takes forever to find a decent board. I had some of my x12s measuring closer to 11 (yes I know they aren't 12 inches).

The door is a little wonky but if it bothers me too much I will just replace it with a curtain on a tension rod.

I love the yellow and I am very proud of myself :)

I didn't have a Kreg jig (too expensive for us right now) but it would definitely have been helpful...

On a rainy morning in early January 2015, my wife and I were sipping our coffees and starting to get ready to take on the day. It was a Saturday morning, so we didn't have to go to work. We had moved into our house about a year ago so a few of our rooms were still a little bare and simply acted as play rooms for our daughter.

I walked out of my office, and looked over to the empty dining room which was immediately adjacent. Coming from a large Italian family, most of my childhood took place around a large dining room table at my grandmother's house outside of Philadelphia, PA. This empty room just didn't seem right. I decided to do something about it.

I remembered walking around Restoration Hardware seeing this amazing farmhouse table that was around $2000. Way out of our price range for a simple dinind room table. It also didn't come with any benches or chairs. It would have cost me around $2600 when all was said and it just gave me some severe heartburn.

I stumbled upon Ana's site here and decided to look around a little. Low and behold almost the exact same table was featured here. After getting over a short panic attack about building a piece of furniture that we would be using quite often I headed to Home Depot, got the materials, some new tools and got to work.

Not only do I think it turned out awesome, it was an amazing stress relief. Two weeks later and bought the Kreg Jig and built a matching bench. These pieces are so solid I could drive my car onto them. Thanks, Ana for the confidence to get this done the right way and save me about $2000.

Onto my next project, a jewelry armoire for my wife's valentine's present.

I built this before my son was born to use as a changing table in his room.  I used leftover plywood from another project which made it a cheap build.  It is super sturdy and has plenty of storage on the top to hold wipes, diapers, and creams.  I used shelf lining and bought cute baskets to complete the look.  

SIMPLE MODERN BAR

I modified this plan to use wood that I had and also a piece of kitchen counter top that was left over from my daughters new house.  

We used Anna's outdoor Sofa plans, which were very easy to read. For wood, we kept costs low by using pressure treated wood, and staining it with Minwax Colonial Walnut stain. We did use the lumber cutting service at Home Depot- only $15 for the cuts, and it made the project time very quick.  The cushions were from Lowes, and throw pillows were purchased the previous season at Homesense. We are so happy with how it turned out. Thanks, Anna!

This was my first Ana White project! I didn't do the x's on the ends, obviously, and it's both taller and wider than the plans in order to fill up the giant space along our back wall. I notice the glue blobs that didn't stain, and the decorative hardware was trickier than I expected, but it was fun to build... and totally functional :)

Thanks so much for the plan!

Welcome to our labor of love. This is our first build and while my bf did most of the work, it was a great project for us as a couple. It was definitely work, but well worth it. We love the way it fits perfectly in our courtyard and people keep commenting on how high-end it looks. Thanks for the plan, Ana! The project took a little longer than it probably should, since it was the first project for us. You should account fort he time it will take to cut, sand and stain your pieces before assembly. There are times you will need to allow for the lumber to dry etc.