Community Brag Posts

Very straightforward build. Lowes didn't have many 2x4's that didn't have some sort of warp or bend in them so the bottom shelf had to be trimmed slightly to fit. 

There is a sweet spot with the vinegar/steel wool that takes some mixing and testing to find. To strong a solution and the wood turns nice and brown to weak and it's a hardly noticeable light grey. My advice is get a strong 3-4 day old solution and mix 50/50 with vinegar and test on scrap, wait and hour or so to dry and adjust the mix from there until you love it. 

I finished with minwax polishing wax.

I made this for my Mom for Mother's Day. She has been wanting a little table to put next to her recliner (where she knits, reads and watches TV). For the top and drawer, I used Douglas Fir from Lowes. The rest is whitewood and redwood (legs). Overall the wood cost me about $50. I painted the body with high-gloss white paint and the stain on the wood is a mixture of min-wax Golden Pecan and English Chestnut. The finishing took the longest, but the build went very quickly.
I did notice that the cut list is a little off. You need 4 of the 1x2 pieces for the sides, not just two.

I may put a layer of varnish on it, but as of now it is not varnished.

Made a set in Kansas, moved em to Texas with us and couldn't move them to Kentucky, so I had to build another set! I know, such a shame right! Lol. These ones turned out better than the first! The first set was just stained, I got a little more crafty with these!!

Fun project!

I had a friend ask me to build this for her daughter. The bars are bungie cord that you can order by the roll. I made 3 frames the same size then put 2x2's on the inside corners and counter sunk the screws the stapled the bungie cord at the top and the bottom. I would highly recommend securing this to a stud in the wall incase a little one tried to climb on it.

Sliding barn door console

My Wife asked me to look into a night stand for her. I am so so so thankful that I was able to come across Ana's site. I showed the site to her and she asked me to build this night stand as opposed to going out and buying her some expensive poorly built nightstand. Thank you Ana for this wonderful site and the inspiration that some of us need to "get started."

One thing that I didn't think about when I started this project:
The cut list is a suggestion of what you will need to cut. I only ran into one major issue and that was with the inset bottom of my pull out drawer. I cut my drawer sides to the dimensions on the cut list (not paying attention to the note from Ana) and had to adjust my cuts for the drawer. I ended up ripping down the remainder of the 1x12 and paired it with the 1x6 that I had left over. Using the Kreg Jig I now had a perfect fit for my drawer.

I would have liked to have had a darker stain (more of an espresso) and that is my fault for not buying different stains and testing them on my wood choices. As far as my wood choices I used 1x6 and 1x12 "white board" 1x2 and 2x2 precut pine and bought a scrap piece of 1/4in plywood for the backer.

The Kreg Jig made this project very easy to complete as well as my counter sink drill bit. Although not impossible to complete without these two tools it is remarkable easier to complete.

I cannot be happier with the final look of my new bed. I decided to take on this task with intentions to make small changes in the plans based on my needs and preferences. The process was easy and original plans were definitely easy to follow. I had the head or foot boards completed in about 3 hours (without the herringbone pattern). I saw where someone else decided to add a herringbone design and I liked it so I did the same. It was a little tedious but overall not hard at all. Building the frame was easy as well and didn't take long at all. I started running into problems when transporting the footboard. I dropped it from about 2 ft and the leg post snapped off. I thought the pocket holes were not that strong from the beginning. This was not a problem though because I just followed the special note in the instructions and added a 2x2 to the back of each side and attached them with 3 inch wood screws. I did this for the head and foot board and it made me feel more comfortable with the stability overall. I was going for longevity for the bed so I wanted to make it easier to disassemble and move around (screwing the frame in would wear out with a few moves). I went to a woodworking shop and picked up some 5/8 inch insert nuts and bolts to match. I added one to each corner and tightened accordingly. This was by far the biggest headache for me. If I could do it over again there are a few things I would change.
1. I would have sanded my cedar post before attaching them
2. I would have attached my cedar post with the 2x2 and not used pocket holes (I l like pocket holes but not for such a heavy load)
3. I would have drilled and placed my insert nuts on the post before attaching anything to them (this would have helped to ensure a level hole).
My wife and I love the natural look of the wood but it doesn't really go well with the modern contemporary look in our home so we are having a hard time deciding on paint or stain. We are leaning toward stain because we love the grains throughout the bed.

This was based on FatBob2Ks great design.  I took iut the Xs used 4x4 legs and 2x6s fir the bottom shelf.  I also put a furring strip around the edges to hide the end grain and add some surface area.  I sanded starting with 89 grit, then 120 and finishing with 150.  For stain I used a rag to rub on General Finishes Java Gel Stain for 2 coats. it's really forgiving on bare wood and you don't need conditioner.  I sealed everything with Minwax satin poly wipe-on and did three coats.  

Replacing a trash bin for a friend whose cats could not get into. At the last minute I thought a little hiding area on top would give them some storage for bags and things. Had to go one size down on the Rubbermaid to allow for clearance when tilting open. They love it, the cats hate it.

I had a lot of leftover pieces of wood from other projects and really wanted to use them. I have been wanting to build the Liberty Wall Art for a while so I finally got to it. I already had a 2x2 piece of a 1/4 inch plywood so I made my piece smaller, fitting my plywood. Obviously, since my piece was smaller I cut and played with the pieces until it looked good to me and this is how it turned out. I glued everything to the board first and then nailed it from the back because my husband didn't want to see the nails. Also, he didn't want me to distress it so I went with his wishes. I think it would have looked nice distressed but oh well, still looks nice. With my husband being in the military, I really wanted this piece and now it's featured in our dining room! Thanks for the idea Anna! As always your plans are great. We have already build several items from your plans and I can't wait to post these brags!

This was my first furniture build & it was very easy. I had to have a second pair of hands to help hold the ends up but other than that I did it by myself. Thank you Ana for making this build so simple.