Stacking Cubes

Submitted by Ana White on Thu, 09/16/2010 - 08:32
Difficulty
Intermediate
| Print this plan

Cute little cubes that stack and store!

For months, I've wanted to post plans for cubes that stack and hold tons of items.  But I wanted to build them first, so you can see a photo with the plans.  And they are just so adorable, I could use them in my office.  But time doesn't allow.

I really loved these, but I personally could never afford $365 per cube.

Much less affording three of them to make a window seat.

Good thing we can build them.

This plan makes good use of scraps.  So if you have some 1/4" plywood, 1x12s or 1x8s in smaller pieces, get your measuring tape out. If you don't, here is what you need

Dimensions
18 1/2" wide x 17" tall x 13" deep (approximate for each cube)

Preparation

Shopping List

6 feet of 1×12
26″ of 1×8 (for optional doors)
1/4″ Plywood
1×2 – 8′ Long
24″ of 1×3 (for feet, you can use a 1×2 but I like the chunkier look better of a 1×3)
2″ Finish Nails
1 1/4″ Finish Nails
2″ Screws or 1 1/4″ Pocket Hole Screws

Common Materials
120 grit sandpaper
primer
wood conditioner
paint
paint brush
Cut List

2 – 1×12 @ 16 1/4″ (Sides)
2 – 1×12 @ 17″ (Top and Bottom)
2 – 1×3 @ 11 1/2″ (Feet)
1 – 1/4 Plywood @ 18 1/2″ x 16 1/4″ (Back)
2 – 1×2 @ 16 1/4″ (Face Frame Sides)
2 – 1×2 @ 15 1/2″ (Face Frame Top and Bottom)
2 – 1×8 @ 13″ (Doors, Optional

Cutting Instructions

Please be aware that this plan uses 1x8s for the doors, and 1x8s can vary in width. I it is recommended that you measure your 1x8s first, and adjust the width of the interior of your cabinet to fit the doors with even gaps around the doors.

Tools
Tape Measure
Speed Square
Pencil
Safety Glasses
Hearing Protection
Drill
Circular Saw
Power Sander
Drill Bit Set

Instructions

Step 1

Handles

These have got to have handles! Measure and cut the handles out with a jigsaw. Prefer a rounded corner on the handles? Visit this post for instructions on how to do that. Just make sure the top of the handle is at least 1 1/2″ from the to

Step 2

Build the Box

I highly recommend using pocket holes to build your box. But if you do not have a Kreg Jig™, you can use finish nails with a nailer or 2″ screws and glue. All joints will be reinforced with a face frame and back.

Step 3

Feet

Use 1 1/4″ finish nails and glue to attach the feet. Notice how the feet do not overlap the sides.

Step 4

Back

Tack the back on with 1 1/4″ nails and glue.

Step 5

Step 6

Face Frame Top and Bottom

Finish the face frame by attaching the top and bottom with 2″ finish nails and glue.

Step 7

Doors

If you choose to add doors, use hinges to attach doors to face frame. Cut out shape as desired to act as a handle with a jigsaw.

Help Improve This Plan

We apologize if there was an error in this plan. Please help us out and report any errors here.

Comments

lyndyjo (not verified)

Thu, 09/16/2010 - 11:41

Ana -- If you put three together as a window seat, would you put another board on top to make one continuous seat? Could I just upholster that one before attaching it? I think these are adorable! How can anyone afford to pay that much for cubes?

Ana White (not verified)

Thu, 09/16/2010 - 14:18

Yes - so glad you asked! Just put a board on top and you got a bench. The height would be very close to standard 18" bench (and coffee table) height. Check out this site for more ideas on how you can use these cubes to make storage beds, room dividers, play tables, and so much more!

Silky (not verified)

Fri, 09/17/2010 - 05:07

They are wonderful.
Ana, you are amazing! Too bad your site didn't exist when we furnished our son's room.

SJC (not verified)

Fri, 09/17/2010 - 13:40

I really want to make these for my 3 year old's room. I am thinking they would be adorable with a heart cut-out though!

Niki (not verified)

Tue, 10/05/2010 - 10:46

I'm in the process of making these. I've done some basic building myself, but this is my first KOW project, and my first time actually following plans. I've got two built. I was putting the doors on the first one, and saw that they were too narrow. I had almost an inch gap between the doors. I measured my 1x8's, and they were actually 3/4 x 7 1/4 (instead of 7 1/2 as the plans call for) . I was going to take the 1x8's back and complain, but did a quick google search first and everything that I could find said that 7 1/4 is the true measurement for a 1x8. So now I think I will buy a 1x10 and rip it down to 7 1/2.

The moral of the story. Measure. Everything. First. Lesson learned. :)

Melinda Mantilla (not verified)

Sat, 10/09/2010 - 03:00

Do you all think it would be possible to add a shelf in the cube? Is there a way to do it without affecting the outer cosmetics of the cube?

McKay (not verified)

Tue, 10/12/2010 - 06:48

I agree with Niki! Measure and measure again! I made three and used one sheet of birch for the faces and doors, they were a little too wide because I cut them to 1x8, rather than the finished measurement on the plans. Make sure to read through the whole plans before you let your excitement take over. :-)

These were still really easy to make! And the Kreg joining system is amazing!

We move often and I never wanted to invest in a big storage unit that would take up a big wall - these are perfect! I can arrange a big wall of them if I want or distribute them throughout the house! I will definitely be making more! And now that I know how they work, I might try making a few bigger ones...

http://lh5.ggpht.com/_bQRCNdiQOtk/TLSDYIEAV_I/AAAAAAAABKY/R1x_7LgHVd8/I…