Community Brag Posts

Made this for a fund raiser auction.  Highest bid of the event.   :)

This was a part of my recent bathroom remodel (new floor tile, shower tile, toilet, and vanity). The plans came out of looking at my favorite home sites, which for this were Ana White and Remodelaholic, and realizing that the vanities in my price were were cheap and not that cheap.

The vanity build itself didn't take that long but had to be done is small segments due to lack of one giant clump of time. Total wood cost was around $60, plus $5 for the gloss polyurethane, $60 for the sink (clearance) and $100 for the faucet. More importantly, the vanity fits the space that I had in the efficient bathroom.

My niece asked that I build  a sideboard to match her farmhouse table.  It was a good learning experience for me.

I decided to build a table large enough to fit me and all the kids. Looking forward to decorating it around Christmas time.

This was my first woodworking project.

The inspiration for the project came from the "Dark Mahogany Chase Chunky" headboard from World Market. At $300 (at the time) it was out of my price range. But after looking at it for a while, I decided I could do it myself.

I used and modified several of Ana White's headboard plans to come up with the final (rough) idea.

I used 3 2x3 boards for the frame, a 3/4" thick piece of plywood for the body (which I had cut at the hardware store) and a 1x2 to top the plywood. I was just going to paint the whole thing but I found these bamboo placemats and decided to incorporate them into the project. At $1 each why not? I used 3/4"x1/2" S4S Moulding for the grid.

the cost of materials was about $66 but I had enough plywood left over for another headboard.

When I showed this kitchen island plan to my wife, she said she wanted it, but with a vertical drawer on the side...  Me, I wanted to modify the drawers and shelf to use the full width of the kitchen island.

I had to modify the plans a little bit more because it's built 100% from maple. Since my maple lumber is 1"1/8 thick after planning, I could not get exactly the 2x4 size obiviously.

The sides (behind the X), and the top are boards that I glued together (laminated).

The drawers have X "signs" to copy the X design on the sides of the kitchen island.  First I made a frame around the panel, and then added a X inside.  It may seems rough to get the right angle for the X, but I found a trick!  I measured the angle with a rope from side to side of the panel.  I set the mitter saw to this angle and never touched it again.  To make the opposite angle (center of the X), I cut a scrap of wood with this angle, reverse this piece of wood and cut the X decoration while holding it side by side with the piece of scrap wood. 

Another little modification:  the drawers have full extension sliders for smooth operation..

thanks for the plans :-)

Eric, Quebec, Canada

Thanks for the idea, we really needed this kind of desk.

Took a weekend when I got time off of work. Would do things differently the next time and love the kreg jig. Will be buying the kreg jig clamps soon.

Used plans for Alexia bench.

I used leftover 4 x 4 pine we had for the legs.  I bought some paneling and moulding to dress it up.

I also used leftover flooring for the drawer faces.

I love this apron, perfect for hiding pencils from my husband.

Just started woodworking. This is my first ever build. Surprised with how sturdy this bench is. 

For my first build I am super proud. Plans were very understable & made it easy to build. Definitely looking forward to building more things! 

When my sons outgrew their twin sized beds and primary colored room, I had already fallen in love with Ana's storage bed collection. I was happy to see that a full size bed was included in the plans. Building it yourself means you can adjust any plans to fit your room exactly, and I planned to squeeze storage out of every inch of their 11.5 foot wide room. The first adjustment I made was to make the headboard taller, so that their pillows would not rest against the small hutch with doors. I also added height to the cubby hutch, making it a 9 cubby unit. The entire bed unit is 92 inches tall. The center tall bookcase is actually two 47 inch tall units stacked. I have watched too many home improvement shows where tall units are built off site only to not fit up stairs or around corners. The center unit is 94 inches tall and 19 inches wide, filling the wall exactly with only an inch of wiggle room to spare. I also added drawers to the open cubbies in the bed base. This was my first time making drawers, but Ana has instructions on the site, so it was no problem.The sides of the bed base facing the walls are just open cubbies as in the original plan. Beadboard paneling faces the drawer fronts, cabinet backs and the face of the headboards. Did I mention how much storage these beds have? The hollow headboards are not accessible once the center bookcase was in place, but that didn't stop me from filling them up. I had 6 Rubbermaid bins (18 gallon) in our basement full of stored Hot Wheels, Little People and other sets. All of the contents fit in the headboards alone. I also put some large saved toys in the under bed cubbies that face the wall. Yes, the Little People Garage will fit! My favorite modification was added an extra crosswise 1x3 that ties together a large section of the slats that support the mattress. This makes an easy lid allowing that you can lift to access even more storage under the mattress. We store their camping gear and off season clothes under the mattresses. I can't total the hours, I worked on this project on and off for about 9 months. When the building was nearing completion I started looking for bedding so I could match the paint colors to the bedding. I painted all the plywood back panels before attaching them to the cabinets. This was especially a life saver with back of the 9 cubby unit, as there are four colors in this section. After painting, everything was glazed with Valspar Translucent Color Glaze in Mocha. When this layer was dry I coated everything with a protective coat of Minwax Polycrylic. If you are wondering about dark circles are at the top of the unit near the ceiling, I had a great idea to use solar landscaping lights up there for a soft lighting effect. It looked great for a few nights until the batteries wore out. There is not enough natural light in the room to charge them. They have since been replaced with a couple strings of cheap colored lights. They are shoved way back towards the wall where you can't see the wires, but are on a timer, so at night they give a nice glow on the ceiling.

I've built a lot of things...mainly corn hole boards for friends and family but this is my first furniture build. My wife's Valentine present! Now I'm thinking my new big screen tv sure could use a nice Apothecary media cabinet.

I tried to make a similar sand box as yours but as space was limited I decided to only make a 1 seat version.  As a first attempt of making something proper I think it turned out well.  Base frame is made of 4 x2s and the lid and seat contruction it pallet wood planed to make it nice and smooth.  Granddaughter loves it.

Rustic table plans with slight modification of the width and the legs were mounted differently for a little added flair. So many finishes to choose from....

I altered the plan a little - this is 40" square.  I edge-glued planks for the bottom level, so I had them sit on top of the aprons instead of inside them.  Note: if you have top and bottom aprons attached to the legs before you put the bottom in (that will sit on top of the apron and not within), you can't get it on in one piece...oops. :) The most difficult part was the herringbone - figuring all the dimensions, cutting everything precisely, getting all pieces to fit, and finding a way to attach it to the framing boards and support in underneath.  I love the table, but I'm very frustrated with the finish.  It's so blotchy, and I tried to do everything correctly to prevent that (see info on the finish).  With every project I learn a few things...