Community Brag Posts

My first woodworking project.  The plans were fantastic and easy to follow. Thanks!

Loved the simple lines of this project - the first one I attempted! I used a 1x10 instead of a 1x12 (because it fit better in my space) with the called for 1x6's. I looked for an interesting piece of knotty pine to add some interest. Two stains were layered and a top coat was added. Timeline is total time but spread out - includes time with a paint brush but not drying time.

I made this porch bench for my daughter-in-law 's birthday. She purchased bench cushions from Pottery Barn and asked if I would build the corresponding bench. Using the dimensions of the cushions and examining online photos I was able to build the framework and tried my best to duplicate the
Chatham series bench. Not quite ready to tackle the curved bench rest and arms but after watching YouTube on how to make curved woodworking items I might just take a shot at it next time.

She really loves the bench and I am pleased with how it turned out.

I changed up the legs because I had a beautiful piece of reclaimed wood I've been looking to use.  I did use these plans for the concrete top and it turned out great!  Just followed all of her advice.  It's very smooth, almost feels like soft cotton, with only tiny bubbles.  Thanks for the great plans!

I built this lovely, modern park bench from plans I found at Ana White. The only adjustment I made was to make the legs out of 4x4s. I like this plan because it's all straight, right angle cuts, a one day project, which I tackled by myself. I'm definitely getting more comfortable with the miter saw. The wood cost under $50. I plan to paint it with primer, then white exterior paint, both of which I have around the house. Stain would be beautiful, too. If I had to do it over again, I would paint all the pieces before assembling. And I wish I had a brad nailer; it would make attaching all the slats go much faster, and would have to fill as many screw holes.

Built this with matching benches that will store underneath the table completely.  Thanks for the great ideas!!

When we resurfaced our deck last year we had to remove the built-in benches due to code regulations, so I knew I would get to make new benches this year. We wanted them to be a flexible size so we could rearrange the deck easily for eating, entertaining, enjoying the sun and the shade. Based on the size and shape of our deck, a square table for 6-8 people was going to be the best option.

After looking at a couple design plans, I decided to combine a few plans to get exactly what we wanted. To get a mid-sized square table I used the leg structure of the Fancy X Table with the construction method and the stability from 2x6s of the Square Pedestal Table. The top is joined from seven 45.5" lengths of 2x6 and two lengths of 2x4s. It ends up being 52.5" square. It is snug for eight people, but comfortable for six. We didn't end up using the skirt boards so there would be more knee room. The base is mounted on the diagonal for the same reason.

For the benches, I used the supports from the Fancy X Benches, with the bordered top from the Triple Pedestal Farmhouse Bench, since it would match the table top better. The benches are 48" long, and only two supports were used for each, inset 5" from the end of each bench. Likewise, I used a single stretch of 2x4s for the seats rather than seam them in two parts like the 106" long original plans. I did add an extra 2x2 support board under the seat platform to keep the 2x4s even over time. Overall, I made five benches - four for around the table and one for next to the BBQ. They are blue so they provide some color against the brown deck and green tree tops that surround the deck.

For both the table and the benches, I pre-stained the surfaces that make up the inside of the Xs. It made it easier to get good coverage there.

I also made a quick flip-down BBQ prep station, on similar lines to the Flip-down Wall Art Desk out of two 5/4x6 and two 5/4x4 cedar boards. The shelves are on adjustable pegs.

The costs broke down - with all hardware, screws, putty, sandpaper, stain, etc. - as: $90 for BBQ station (lots of hardware), $200 for 5 benches, and $155 for the table. I did a lot of sanding and filling to get the rough 2x4s smooth. In the end, there was about 50 hours in the benches, and 20 in the table. The BBQ station was less than a day, including mounting.

Thanks to Ana White and Lady Goats for the idea from their prior plans on the Rustic X Bookshelf. The bookshelf is 6ft tall and the shelf height is perfect for DVDs or books.

Submitted by Valeria Green -

My husband built this table and bench for my son and his wife. He is presently building another by request for a young couple.

It didn't take me long at all to make these. I enjoyed making them and all my neighbors love them. They have a nice amount of space. I actually had to make mine smaller than the instructions. I had most of the wood on hand.

This was one of those "Labor of Love" projects. I was nervous about the rockers but the hardest part about them was getting the ends rounded perfectly. I didn't scribe the legs, instead I cut and assembled both sides and then laid them up against my rocker 1x4s. I marked where the legs met the rockers and then cut the rockers leaving the areas where the legs met at full width. Made it much easier. I also rough cut the rockers and used my orbital sander to bring the wood down to my pencil lines. I had the rockers clamped together for the entire sanding/cutting process. I love the silky smooth finish of the milk paint and hope my nephew and his wife love the finished cradle as much as I do. Thanks for a wonderful project Ana!!

Submitted by Carla Santiago on Facebook - 

We did a bench, I got your plans off Pinterest. We just put a slight slant to the back and we love it. Thanks for the great plans.