Beginner Farm Table (2 Tools + $50 Lumber)

Submitted by Ana White on Mon, 06/25/2018 - 00:16
Starter Projects
| Print this plan

The easiest rustic dining table that you can build!  Perfect beginner farm table plans by

I have been a long time user and fan of Rustoleum products.  This post is sponsored by Rustoleum by all opinions expressed are my own.

UPDATE: Bench plans have been posted here.

UPDATE 2: We added a tinted poly coat to the table and it now looks like this!


I've been wanting to get the beginner crowd a VERY simple, inexpensive farm table plan for years now.  Just because you aren't an expert woodworker with a zillion tools doesn't mean you can't still start somewhere, right?

Well, I finally got my chance!

We are moving into the new house, but with so many, many functional projects to tackle (like closets and pantry cabinets), a beautiful dining table is way down on the priority list.  But still, I insisited we need a dining table to move in.  Once you give in to the kids eating on the couch, you're done ... or at the very least have to be the bad guy and retrain the family.  

So I gave myself three criteria for a new somewhat temporary dining table -

  • Must cost less than $50 in lumber
  • Must be done in an afternoon
  • Can only use 2 tools - a drill and a saw (since most beginners don't have a Kreg Jig yet - and I do stress yet) 

This is what I came up with -

And here's how it went down -

I purchased 6 - 2x4s and 6 - 2x6s in stud length.

The 2x6s are for the tabletop boards, and since they are all precut exactly the same at stud length, I set them aside - no cutting required.  My table will be 92-5/8" (standard stud length) long.

There's only 12 cuts on the entire table, and it's all the 2x4s.

I used a compound miter saw.  You can use a circular saw or jigsaw, but do make sure your cuts are very good and straight.

Cutting done, time to build!

For attaching, I'm using 2-3/4" self tapping screws.  You'll need about 100.  Bonus - these are exterior screws, so I could use my table outdoors too.

Alrighty ... let's build already!

I used scrap pieces of 1x boards to elevate the horizontal boards on the legs.  Then I just screwed from the outside.

Two leg sets done!

Then I flipped everything over and added the side aprons.  One trick is I will screw at an angle (kinda like a pocket hole screw) in opposite directions, so if the table is wobbled at all, the screws dig in from opposite directions. 

Then I flipped everything back over and checked for square.

Way out - like over an inch.

So I pushed the two shorter diagonal corners together until the two diagonals matched.

Then I added the bottom stretcher.  The ends overhang 3/4" - be careful that your legs are square when you add the stretcher.

The middle support piece keeps the aprons from spreading, and also give you something to attach the tabletop boards too.

Now for the top - I like to start in the middle and work outward.  So I find the middle on both ends,

And then I attached the 2x6 studs to the top with screws.  I am careful about screw placement so it looks good in the end.

NOTE: Since we aren't joining tabletop boards together edge to edge, there may be a small gap between boards.  You can fill with silicone after final finish, or use a Kreg Jig to build your tabletop first, then attach.

I was going for a rustic real wood look, but decided to sand to take splinters and rough patches out.  I started with an 80 grit and finished with a 120 grit.

Table is ready for a finish!

I love Watco Danish Oil because it is a beautiful, durable finish that is easy to apply - so much I wrote an entire post about it!  

Danish Oil is a color and finish in one, so all you need is one coat!  You can go back and further seal the table (or just the tabletop) if you so desire.

Gotta say, I do love how this one turned out!

You can also watch the video tutorial here -

If you likey, do let me know, and I'll get you those bench plans too! UPDATE: Bench plans have been posted here.

The plans follow, if you do build, please share, it's a great joy seeing your projects too.

Have a good one!



Dimensions shown above


Shopping List

6 - 2x4 @ 8 feet or 8 foot stud length

6 - 2x6 @ 8 feet or 8 foot stud length

About 100 2-3/4" self tapping wood screw

Wood glue

Clear Silicone or Dark Brown (depending on your finish)

Watco Danish Oil 

Color matched wood filler (for filling screw holes after wood staining is dry)

Cut List

8 - 2x4 @ 28-1/2" - end leg sets

2 - 2x4 @ 75-1/2" - side aprons

1 - 2x4 @ 80" - bottom stretcher

1 - 2x4 @ 25-1/2" (middle support)

6 - 2x6 @ 92-5/8" (tabletop boards)


Tape Measure
Speed Square
Safety Glasses
Hearing Protection
Miter Saw


Step 1

Build two of the leg sets with 2x4 boards cut to 28-1/2" long

Step 2

Will leg sets upside down, on a flat level surface (be careful on garage floors as they usually slope) attach aprons to leg sets.

Step 3

Flip over and adjust for square.  Then attach bottom stretcher with equal overhangs on ends of 3/4".

Step 4

Add center support.

Step 5

Step 6

Attach next boards as close as you can to first boards.

Step 7

Repeat for final boards.

NOTE: I also angle screwed from underneath on inside of apron into the underside of the end tabletop boards for extra support.


Mike Mercer

Thu, 12/28/2017 - 10:48

Looks great, I love the colour.  And the chairs look great too, as they go well with the table.  I hope mine will look as good when it's done.  Did you use a darker stain on the table top, or was it painted?

Mike Mercer

Thu, 12/28/2017 - 10:45

Hi Ana, 

It's nice to be on your site getting plans and building projects.  I was so inspired by you I went out and bought Ryobi tools, and have since built 3 projects all on by you.  I loved building the Potting Table, and better yet my Mother loved it when I gave it to her as a gift.  I am now working on the Farm House style Table and Benches.  I can't wait to see how they turn out!  

Ana I wanted to Thank You!  Your designs are simple to understand, the cut lists are great and better yet the instructions you provide are the best.  I can't wait to build some Outdoor Couches when the weather gets better.

One day I hope to be doing what your doing, working with projects and making a blog, and who knows maybe I can get people to buy them! 

Thanks again Ana!


- Mike.


Sun, 01/07/2018 - 15:14

I've never built anything before, but I really want to make this. My space isn't big enough for the length of this table. My table needs to be 80" Long. My table can still be 33" wide. Is there a tool I could use, or can someone explain how to make adjustments to the measurements in the plans to change this to an 80" table? Your help is greatly appreciated. Thanks!


Fri, 02/02/2018 - 14:02

So the plans were awesome and easy to follow.  Only issue was user error on my part.  When I bought the wood I didn't ensure the boards were not bowed. This became apparent as I started assembling. Now my completed table is twisted like one of those cinammon twists from Taco Bell. If anyone has any suggestions on how to rectify my issue please let me know .


Tue, 06/11/2019 - 07:26

Thank you, thank you!  These directions were so easy to follow and I built a beautiful table for my new patio.  :)  I love it so much that I want to build a coffee table just like it.  Because I am so new to this, I don't want to tweak things on my own and mess up measurements.  What suggestions do you have on plans and how to use this design to create a 2 tiered coffee table? Thanks.  Niki


Wed, 06/12/2019 - 04:08

Thanks for the plan - I built this table in a couple of hours.  I adapted a few things -- because this is going to be a patio table, I needed to make a center hole cut for the umbrella.  Instead of the center support, I made two supports spaced evenly apart.  Besides giving me a place for the center hole, it added strength.  Additionally, I used a 2x6 for a stretcher, and as able to secure it to the inside of each side, which gave a more finished look and added support.