Community Brag Posts

This is my first project attempt from Ana's plans. I had to modify it greatly to fit my space accordingly. The room where it made its home only has a love seat and a recliner. The space also isn't that deep, so i made the table aprox 45" x 19" x 18" high. I also built a completely different top to this table as well. I felt this fit our personal style a little bit better. So being that this was my first project, it was a little more challenging due to all the measurements had to be changed. I wish that I could have just folloed Ana's plans to the tee, would have been a little easier. So after I assembled the basic frame, i assembled the top using pocket hole screws, glue and clamps. I used three coats of stain, with sanding between coats, two coats of clear Satin laqcuer and finished it off with a paste wax. Buffed the table with a cheesecloth and microfiber towel and then introduced my living space with a new, handmade table. My next builds should go a little quicker because I will follow the building plans exactly as they show. I hope you all like the table and look forward to hearing your comments on them, good or bad. Any suggestions to help me along the way would be greatly appreciated. Thanks for taking time out of your day to read this and again, I hope you enjoyed my first real, finished furniture piece.

Dennis

Check out all pics from this project in my Google Web Album by clicking on the blog link

Our Vintage bar stools that are not complete yet.

I could not find a big enough, awesome enough trellis in stores, so I built my own out of cull lumber [the stuff on super-clearance no one else wants] for about $12 and a left-over post pocket. Thanks for the inspiration!!

I built this after going dumpster diving for pallets. We went through and broke up all of the pallets and basically made this entire big piece for the cost of the stain, nails, and backing.

Inspired by Ana and driven by a desperate desire to nest, I made this table in my first-trimester. We live at this table. It's where we eat, play, and craft. On special occasions we stand on top of it, and sometimes we even eat under it. We love the way it looks in our mid-century ranch house with modern chairs. Thank you, Ana!

This was a lot of fun to build. Took a few hours while kids napped plus a few more after bedtime.

When a plan calls for a 2 x 2, you may be able to add a little extra detail by including spindles. I was able to with the Farmhouse Bedside Table! The top of each leg is a plain old 2 x 2, to accommodate the drawer section. Just below that is a spindle with the top squared-off section cut off. The bottom of that spindle is attached to the top of another, where both were squared off and the same dimensions. This "ugly" joint is why the piece of furniture is painted instead of stained--even then, because of variable grains, this specific seam can be seen on close inspection. You can potentially stain furniture that has spindles if you can match the grains and are not connecting two ends that have exact dimensions, which would create an even more obvious seam on stained furniture. Where I joined two pieces of differing dimensions (example: circle to square), there is no visible seam.

To accommodate the specific spindles I wanted to use, the main dimensions that had to be changed were merely the height of the cross bars and shelf. However, with cuts, I waited and cut them (and had larger ones cut at stores) as I went, to help get them to be more exact since the 2 x 2s were slightly off from the spindles' squared-off area.

This all may sound complicated, but it wasn't!

To get the correct leg height, I first cut one end off two spindles and put them together with the two intact ends meeting. The resulting dimensions were subtracted from the required leg height of 26 1/4", leaving the length to cut the 2 x 2 at. This required a lot of measuring, being sure that the legs would be "squared off" in the areas for the drawer and shelf.

To make the "joints" between the legs--each of which is three pieces (!), I used 1/4" x 1 1/2" dowel pins. These are readily available even in craft stores. These aren't the same as dowel rods--they have grooves in them. Next, drill holes the dimensions of the dowels in the exact middle of each leg piece, and put glue inside the hole and around the top of the smallest-dimensioned piece. Connecting and clamping as you go, this will create stronger joints than just using glue.

After the legs were made, I followed the instructions as indicated, being careful to measure before each cut and adjust the measurements where needed.

For another example of how you can use spindles, here's a cat feeder I designed and built back in January:
http://flattops.webs.com/petfeeder.html (Purchased ones in real wood are usually over $100!)

Though it's far from perfect, I'm really happy with how the table turned out--and hope that my experience may inspire you to give spindles a try! I'd love to know how you use them!

Our puppy needed to move out of our bed, and I love the looks of the Lydia toddler bed, so we made this one for her!! It's fantastic and I'm so happy with how it all turned out! It was Mike's first time using a Kreg Jig and he loves it!

I made this for my son's second birthday last year.

I made a few changes to the plans. Instead of a shelf in the oven, I put in a wire cooling rack to resemble a oven rack. I put knobs on the back of the stovetop instead of the lower front. I added doors to the lower half on the sink.

The sink is a 9" loaf pan. The stove knobs and faucet were salvaged.

Toy food and realistic pots and pans are from IKEA.

Made a few design changes as I went along, but overall the plans were great. And with my wife's finishing we have an antiquey farmhouse table. 

My husband and I made a toddler picnic table for the grandbabies out of reclaimed wood from pallets. I have a bench sander that I used for a lot of that wood, but wow what a lot of work. So for Mother's Day, I asked for a Dewalt thickness planer, and I have to say I think that's been one of my best purchases in a while.
I had no idea how beautiful some of that pallet wood could actually be until I started running it through the planer.
I needed a book / magazine shelf in my guest bathroom so I used a plan submitted by a guest, modified it a little and used my reclaimed wood.(Flat Wall Bookholders) I used an oak poly stain in order to bring the grain out some. I couldn't be happier!
Thanks Ana!

At first I was going to stain these ledges so I only used pocket holes to attach the back of the shelf and I attached the front using small finish nails. The back and the bottom are made from a 1x3 and the front is a 1x2.

Check out my blog post for more information.

My wife wanted an outdoor server for our back deck. I did so, but decided to add some flare. I built it so the top comes off and a cooler is exposed for our drinks. And to not waste any wood, you turn the top around and I painted with Chalkboard paint so she could write up a menu. Added some color she would like, found a tutorial on chevron, add a few accessories, and viola!

Our daughter loves to use it as a place to store animals as well as books. 

I modified this plan quite a bit. I chunked up all of the wood for a sturdier table. I also did braces on the underside of the table and benches so there would be no nail/screw holes on the top. For the D, I taped a chip-wood letter from Hobby Lobby to the wood while I burned over the entire top.