Community Brag Posts

This was my first ever Ana White woodworking project.  It was also my first time using a Kreg Jig.  I had a ton of fun and can't beleive how great it turned out!  I learned a lot while building it so I'm sure I will have even more success with my next project.  I highly recommend this project for first time beginners looking for a huge feeling of accomplishment and personal satisfaction. 

Thanks Ana!

Anthony

http://wholesteading.com

We had seen the modern slat bench before, and stumbled upon the plans on Ana-White, we did look further to see if we could find a style for us and had seen one made entirely out of 2x4's that also cam with plans, http://diycandy.com/2015/06/modern-williams-sonoma-inspired-diy-outdoor…

I thought I would share mine as it differs slightly, I opted to age my bench before staining as well as added adjustible feet so I can level it no matter where I put it. I am using mine as a coffee table, and if I have too many people over, I just use it as a bench to accomodate.

I hope that everyone enjoys the look of how my bench turned out. To reproduce the look of mine I described and linked the 2 products I used for the finish. But I also used the following power tools, Table Saw, Drill and Sawzall, belt sander and palm sander. I used the sawzall as I made a slight error and had some overhang that needed trimming. We used numerous items to get the outside beat up prior to the stain and sealer. The finished product looks amazing and I don't fear someone running away with it at 80lbs.

This is my first attempt at making a wine rack. It holds 18 bottles and 9-12 glasses. I made it from 1/2" red oak plywood and 1x3s. I used a drill press with a 3" hole bit and 1 1/2 bit for the neck supports. The one pic shows how I kreg jig the supports to a scrap piece of plywood so I could stain all sides of the pieces at once! Plus it allowed for a quicker drying time. I kreg jig all the supports from the back side with 1" PH screws and glue. I used my router and a straight edge to dado the top and bottom shelves to the side walls. This rack measures 5'Hx 15 1/4"w x 17" deep. The wine bottles do not stick out past the front at all. I stained it in a dark walnut to give it a country feel.

Wanted a chest of drawers with Deep Drawers.  As the drawers were so deep I used some scraps to fit supports to the undersides of the drawers as shown in one of the photos.  I knew the drawers would be stuffed to the brim and would need to be quite strong.  On the bottom two drawers I fitted three supports from scrap 1 by 4 and 1 by 6. 

On this piece I didn't bother covering up all the internal pocket holes like I normally would either and it looks a bit of an ugly duckling on inside but once top is on and drawers are in you cannot see anything.

I thought the natural colored backing gave it some interest too.

Happy to share my plan with anybody who wants it.

I got the legs from a old dining table my mom had that was damaged in a move so when i saw this plan i knew this was perfect. So simple and easy to build, yet everyone who sees it is in love with it. Thanks Ana!

I was so inspired by this site, I just had to try something out for my self! Being a beginner it was a little difficult trying to get the notches perfect without the correct tools! A table saw is neccessary but me and the fiance kept at it! After all assembled we banged up the table with some heavy duty chains, Gave it two coats of Minwax Dark Walnut, and finished with 2 coats of Minwax Poly Satin finish. We left out center support so we could get it in the house and installed once it was in, this is one heavy sturdy piece of furniture!

Printers console

My husband and I built this for a wedding gift.  We love the plans, so easy to follow and alter measurements.  This one is white washed with monogram design.

My daughter and I chose this design for a table for her new apartment. I happened to have some walnut lumber available, so we decided to use that, and it turned out a little less rustic than some of the tables, but it is exactly what she wanted. It was a great project to do with her and we both had a good time, plus she has a piece of furniture she is proud of.

I used MDF and Pine for the build. It's a simple 3 tiered design with a small easy access storage section on top. One end of the top tier has been shaped so that the baby doesn't hurt it's feet when kicking around. The change table also has a decorative trim to jazz it up a bit.

This was first major woodworking project. I used mostly select pine, a little knotty pine and some spruce studs from a local hardware. For the headboard panels I used tongue and groove pine boards. I used Benjamin Moore primer and paint for finish. 

Tip 1: make sure to measure your hallway and doors before trying to bring this from the shop or garage into the house. If building in the bedroom, make sure to plan for the day you want to move it. I ended up taking mine apart to get it through the bedroom door and ruined the finish on all my legs. 

Tip 2: I added blocks behind the legs because I didn't feel like the legs would be sufficient support. I also created by own rear legs similar to the front for more support. 

Tip 3: the instructions on how to mount the headboard to the bed aren't really clear / don't work. I had to add some extra 2x4 material to the rear legs (on the inside)  in order to have something for the bolts to go through. Once your headboard and bed are built, you'll have to be creative and come up with something. 

Tip 4: I added support legs under the cross supports to hold the weight of the mattresses better. 

My wife and I began the Kentwood bed last weekend as a project for 1) our oldest boy needed a new bed 2) a family project and 3) a project that would count for my oldest Weblos project to earn a building badge. After reading up on it about a month ago and finally finding the last Kreg jig in town (fairbanks, ak) we purchased the wood and began the building. This plan calls it a weekend project which it would have been if I had not been in school and other family engagements to get too during the weekend. So the weekend project turned into a two weekend endevor. After much hard labor and buying two cans of stain ( as the first can took a dive onto the garage floor and stained more floor than my project) the finally result is pictured. My wife and I love the look and sturdiness of this bed. After completion and final assembly my only addition or change to this plan would be to suggest using hardware attaching the side rails to the head and foot board, so there is less wear and tear on your project. Thanks for the plans!

This project made from http://ana-white.com/2013/05/plans/mini-farmhouse-bedside-table-plans was a birthday gift for our daughter who was moving into her own apartment and preparing for an approaching marriage. This is exactly what she requested.  While I did use Ana’s posted plans you may see some slight modifications. 

Slimmed down version of the original plan. 60" x 11" x 35". Super happy with how it turned out!

My wife wanted a bench for one side of our dining room table. After looking at prices to purchase, I decided to see if I could build it. This was my first wood working project and I built the bottom half using only a circular saw. By the time I decided on the design for the back, and actually figured out how to build it, 18 months and many other building projects had passed. This is the final piece.

I decided to build a dining table after finding Ana's site and being encouraged from the straight forward plans and great brag posts.  Thank you for the encouragement, Ana!

This project took much longer than anticipated since we changed around the plans, used mahogany which is unforgiving, and I'm a bit of a perfectionist so we spent a lot of time on each step to make sure things were correct.  In terms of modifications, we used 1x12, 1x10 and 1x8s on the table top.  We only made two pedestal legs so we could fit chairs on the end.  The overall dimensions are 96.5" x 46.5" x 29".  We kind of fell into those dimensions after having to change things to make sure the breadboards fit properly.

I'm happy to share any additional plans/information with folks who want to build a similar table.  We didn't use a stain but rather just 3 coats of MinWax Wipe-On Poly.  It really brought out the beauty of the grain and color of the wood!

Thank you again, Ana!  I hope future generations will keep this table and think it's cool that their family made it.  I'm planning to have a plaque engraved with our names and the date to attach to the table as well.