Community Brag Posts

Our attic bedroom had no closet space or storage. I designed a system with shelves and hanging space along one end wall. A freestanding vanity table was discovered at a Habitat ReStore, which fit the space perfectly. One side of shelves is for clothing, the other side is for books and display. A long shelf across the entire top serves as the closet rod as well as display space.

Lots of pocket holes

Dear Ana,

I was absolutely inspired by your fireplace shiplap wall project. After pondering a couple of years to get started on it, I finally brought it to life.

I wanted a rather thin design so I modified it to my taste creating a depth of only 7” inches (2 x 3 1/2 studs). Included a cutout frame for a soundbar and added rear LED lighting.

Very proud of it! Thank you for the motivation, your plans and guidance.

Cheers!

Ron

My inlaws were building a beach house on the coast of NC. After years of going to the beach for family vacation and always renting houses that had water access and boat access, but no where to clean fish when we would return from the pier or boat, I decided to embark on a mission. I was introduced to the Kreg Jig work bench plans and felt that I could adapt this plan into what I wanted to do. I used all pressure treated lunber (including the plywood) and stainless steel fasteners. This did increase the cost, but was necessary for the intended location. I purchased a slab of cutting board material from USplastics.com (24" x 48") and glued and screwed it to the plywood bench top. I then mounted a bar sink and faucet for cold water access and it can either be set up on a dock to drain directly back into the water, or a 5 gallon bucket can be placed below the drain, obviously it could be piped to the drain system of the house also. It came out great. Father in law loved it, and I can't wait to see it get good use.

This is my second table which I built for our new home in the Olympic  Penninsula. Moved closer to our kids when we retired.  It was wonderful to have our kids, their spouses and friends gathered around the table for dinner, conversation and laughs.

This was a custom build for one of my clients in San Diego, CA (Encinitas). She wanted a 9 foot buffet to store all of her kid's toys in :).

We came up with the design, and I built it right before my wedding (probably my most stressful build! haha).

I’m old bloke 85 been retired over 20 years now and widowed found plenty of time on my hands so made a rocking horse for a friend about 15 years ago it sorted of snow balled from there now I’m up to no.35 and couple still in line I use pallet wood  - Bob

Bed built off of plans. For one person this was a big job to finish in 3 days, but I was able to get it done before Christmas.

I made this bed for my son Luke's for 4th birthday. This project was a first for me and I loved doing it. I modified the stairs as I wasn't crazy about how shallow the steps were and how high the rise was. I have 4 stairs instead of 3 and they stick out about 4 inches from the front of the bed. The bottom step is a small toy box and the top 3 are all drawers. I also added a slide. The slide design was the biggest challenge as I couldn't find a set of plans that I liked. I ended up tracing the shape from an outdoor playset that we have. I then created a template and used a router to cut 1/4" grooves into the left and right hand sides. With help, We slid a 1/8" of wood into the grooves. The wood was from home depot, slick on one side. I think it was a Hardboard tempered panel, but I don't remember for sure. The entire project probably took 60-70 hours. The bed itself was about 30-35. The other time was the stairs with drawers and the slide. A good chunk of the remaining time was spent in planning and figuring out the slide and adjusting the drawers. This being my first project, I spent a lot of time just figuring things out. I had never used a router before. I had never drilled pocket holes before. This project opened my eyes to a whole new world.

I doubled the size of the shelves for more storage and made 2 drawers instead of one.  Loved building this and your plan.  Don't think it turned out bad at all for my first time. This looks great in my new remodeled kithcen and all who have seen it love it and are amaze I built it myself. Thanks for sharing your plan. 

I was looking for a small entertainment stand that would fit our blu-ray player and cable box, but also some drawers to hold dvd cases. This looked perfect. I have some woodworking experience but not a lot. I've never built anything with drawers before and I was a little nervous about it. The drawers were definitely the most challenging part and took some modification. If I built it again, I'd rip an extra 1/4" off the drawer sides so they'd fit better vertically. Other than that though, the plans were great. The project turned out very nice and I'm very happy with it.

Thanks for the great plans. I got your book for Christmas!

Built this vegetable bin for my sister in law. Just needs knobs, which I'm letting her pick out. Easy build finished in an afternoon. Stained and painted the next day. Could use this for other storage as well. 

As a stay at home mom of 2, I was looking for a play area to bring indoors for the winter or rainy days.  I came across this clubhouse bed.  I added a slide and a private room underneath with lights and it's perfect.  And since this is a brag page, I just want to say that I built this completely by myself.  It was the first thing that I've ever put together without a kit, so I just went all it.  The kids love it!

I built these for my son for Christmas. They were very easy to build (the 2nd chair turned out much better than the first, however!) and I am very pleased to have discovered this site. Thanks!

Built from the Farmhouse Table plans with just a few adjustments. Total cost around 130.00

This is my second project. It's a coffee bar to free up space in my kitchen countertop. It has quite a few imperfections but I am very proud of the finished product. Can't wait for my next project!