Community Brag Posts

I love how this bed turned out. I made the footboard panel the same size as the headboard because I wanted my footboard above the mattress.(just use shorter 4x4 post for the legs than you do the headboard) I also added some molding inside the panel to give it a little extra flare. The boards on the panels are connected with pocket holes and pocket hole screws and the trim I put on covers them completely so there was no need to fill them in. I ordered some bed rail brackets from Rockler and attached the side rails right onto the 4x4 legs instead of the panels and it worked out perfect and it's very easy to take apart if I ever need to move the bed. Thanks Ana for the plans. Any chance you will be doing nightstands to match?

I decided not to use the wheels to keep my son from moving it around, stained it.

This was a blast. Thanks so much for the plans Ana, as well as for all the comments after the plans, which help a lot too. I did a combo, and it worked wonderfully! I made a little more work for myself than I needed to, but for a first project, I feel proud of myself...and can't wait for my next project.

This table is a dream come true. I have always wanted one of these but could never find one I absolutely loved. I have now.

Fun project that turned out pretty good, we also made the matching end table

These are my wooden magazine files made after looking at Ana's plans. I chose to paint these to match my bathroom.

See more of my build process at http://www.bryanpryor.com/2013/01/26/magazine-holders/

We didnt include the stairs on this bed as there wasnt enough room in my daughters bedroom.  We are very happy with the finished product, and so is my daughter.  We didnt quite make it as high as the plans as we were worried out the fan in my daughters room.

The wood total was about $200. We added some height to the headboard for the build. The frame is done by screwing 1x2 boards along the side rails and laying (4) 2x4s across for the box spring to sit on. Absolutely love our new bed!

Snooker and Pool ball cabinet with lift out ball storage trays.

Wanted somewhere to store the differnt balls and wanted lift out trays so the balls could be easily carried to the table.

Apart from the top the cabinet is made from Poplar.  The top is made from Pine and the sides are 1/4 inch Birch ply.

Used full extension drawer slides.

Actually made the ball trays first and then made the cabinet to fit based on the width of those and the depth they needed to fully extend by to allow the trays to be lifted out.

Made a couple of mistakes on this one and had to scrap the first drawer I made as put pocket holes on the pieces for the sides not the front and back.  Kept the drawer though to use for another project.  Lesson learnt!!

The poplar legs were on offer at Home Depot and only $2.50 each.  Bargain!!

I've been a DIYer for as long as I can remember and recently I decided to start documenting them on my new YT channel. I try to keep the projects as simple and fun as possible for parents with little to no experience in DIY. This project was super easy and my son absolutely loves it. We use this desk for learning and playing (reference video). And since it folds up it saves space for his play area. I hope that you too feel inspired to try a project like this.

My husband and I used your instructions and made this bench! We are further furnishing our home, and we love it! We went with a weathered gray stain to match some other furniture we have.

Loved the twin sized cabin bed but my grandson is a few years away from needing a big boy bed.  Husband scaled down the plans and this  is what we came up with. 

I built this larger than the specs given because I wanted it to hold more. 12in shelves with an 8in back just seemed way too small. That would hold a plant or a bowl (as seen in the other brags). This can hold a plant *and* a bowl. If your space can accomodate it, I suggest making this larger.

This has shelves 16in deep and the back is 10in wide. This resulted in a front profile of about 42in across and a side depth of about 30in. I also added two cross members (?) over the shelves to give it a more finished look

Attach the back to the shelves first and then measure the rest from there. The materials list is modified as follows: back = 1x10x6ft, shelves = 2 x 3/4in by 16in by 8ft (will be enough to make all 6 shelves).

Pine back and shelves but I went with fir for the front frame/doors because the fir was much straighter and less prone to warping. It was my first time using a pocket hole jig. You gotta love that thing. The only other tool we used was a jig saw and a nice long straight edge (and a chop saw - helps with accuracy when building the frames).

Total cost of project was around $300 but considering we couldn't find anything like this in any store, and it fit our needs perfectly, it was well worth the time, cost and effort. The pictures don't do it justice.

Thank you Ana! It was just what we were looking for.

My daughter and I decided to build her a desk this past summer. We went with a precut project board from Home Depot for the top. I didnt like how the bookshelves were attached so I used round head bolts and nylock bolts underneath. This way I can later resurface the top as well as makes it easier to move. We used a redwood stain and 4 coats of clear semi gloss. 

We are loving this outdoor sectional! It was super easy to build! The hardest part was figuring out cushions. I made the bottom cushions and got the back pillows on sale at Costco for less than I could make them. Thank you!

queen size platform bed w matching headboard.. Sunbleached stain sanded to look aged..