Community Brag Posts

I somewhat followed the general context of the plans for the bottom, but I added bracing and general durability changes to the plans. As the original builder did not take thought into the event of moving/ un- assembling, warping, expansion or durability. I used kiln douglas fir  (4x4, and 2x4) and kiln dried pine bread board tops. All bracing joints were predrilled and then screwed in with 4.5 or 2 inch screws, as a kreg jig joint should not have stress- I want this table to withstand someone leaning or in the instance sitting on the tabe to be safe- a 1/2-1.5 kreg screw would not work. I also changed the bread board to a 1x10- as most of the 2x10 at the stores were warped or chemically treated. Underneath we added bracing with an additional 2 2x4 beams, with cross beams in the middle to prevent sress. We opted not to have breadboards, as I did not want to mortise or tenon joint the ends. We followed close to the plans- but inforced stronger bracing to withstand weight applied to the table and easy dissasembly. :)

My cost was a little higher - but I did not want chemically treated pieces or warping. There was additional cost in 4.5 inch screws, and brackets but under 50 dollars. 

Aged rustic turquoise 

I loved this plan as soon as I saw it. The only modification I made was I used a 4x16 8oz drop cloth up on over the center instead of curtains or fabric and painted the wood with orange gloss spray paint. The kids love it. I think we may make come doors and ties to make it cozier but they love it!

My husband built the table and benches and I applied the finish. It pretty much took us most of two weekends, but was well worth it. We learned that we should have used kiln dried wood for the table top, since ours warped pretty significantly. We will most likely replace the planks on top of the table in the near future. Also, the plans for the length of the bench don't allow for the benches to be pushed in under the table. The supports get in the way (make sure your measure!). I used Minwax Ebony stain and wiped it off quickly after applying it, so that the wood would show through. I also used a satin finish to keep true to the vintage look, yet give the table some protection from the elements.

Made a little smaller than original plans and completely out of oak  

I've taken quite a bit of time building this project. My goal was to use all material we had here so, I had to cut down 2x4's and 1x6 tongue and groove. I am proud of how this turned out, now to build it's match.

I started with Michaela's Kitchen Island plan, but reduced the dimensions and material sizes. I used 2x2s for the legs and 1x3s for the rest of the project. Everything was kreg jigged together. This project would've taken less time but the drying time for the stains ate up work time! :)

I built these out of necessity to keep my tipsy Christmas decorations from blowing over. The last couple years I spent a lot of time picking these trees up off the ground. I like how they turned out and were relatively easy to build.

I was excited I got to use my Kreg Jig for the first time, which looked more difficult to use than it actually was. Although these are cedar planters I used all pine from big box orange. Some leftover from the farmhouse queen bed I built and the rest I purchased.

The finish didn't turn out as grey as I would have hoped using the steel wool and vinegar, but I still like the aged look. I added the "x" detail in the front afterward and instead of staining my wife thought it looked better natural. Either way I would have been happy. I will be able to use these year round in some capacity.

My son saw this project and wanted a rocketship.  I was also tired of piling up his books on the floor.  The only wood I bought for it was 1/4" ply for the back as I used leftover 3/4" plywood for the bookcase itself.  Fairly easy with a Kreg, it just took a little while to finish all of the painting.

Made by my husband.

This is a 4 x 6 sand box. I took the Idea from this website and add a roof just for looks. It is made with 2 x 12 , 1 x 4 and 2 x 4. I used Flood Stain which I loved the clean up. I made the second one with 2x12 and 2 x 4 because it was going on a comminuty playground and I thought it sould be stonger. It takes 22 50 pound bags of play sand to fill it. Had a great time building them Thanks for the idea

The plans are pefect. Very easy to follow and the measurements make the drawer install a breeze. Very enjoyable project.

Using this plan I built my lounger with some changes, mainly adding lawn mower wheels to one end. The cushions I made have a mesh bottom to let the cushions dry faster, and zippers so they can be removed and machine washed. More details on what I used and many more photos on my blog.

I made this bench for a friend who had a very specific space that needed a bench. I had to make it so that there was about 30 inches of length on top but with enough room on the inside of the cubbies for 10-11 inch baskets but also had to make it so there wasn't enough space for a dog to get its head into the baskets when they were put into the cubbies. So it took some thinking with the math, but ultimately, I think they turned out great and the 10 inch baskets she bought work perfectly. I made the legs with 1x3s instead of 1x2s for extra support (and that's also what I had in my scrap pile). I left it unstained because my friend is going to do that part. This took about 3 hours to plan and build. I used the kreg jig to hide pocket holes to attach the legs to the top and bottom and also to attach the inside divider to the top of the bench (I used nails to attach the inside divider to the bottom).

This table was modified from a few different plans. I built it as a stereo/radio stand for our cottage. The 2x8s on the top have special meaning as we used the boards as a ramp to haul our fridge in.

Had to build something to go with our brand new OLED TV. Combined Ana's 'Grandy Sliding Door Console' with a modified version of these modern barn door plans found at https://howdoesshe.com/build-a-fixer-upper-style-modern-barn-door/ from @angelarosehome to make the finished product shown here. My wife loves it (the pup doesn't mind it either)! 

My DH and I built this using the side tower plan. It was about $50 in materials, including the birch 1/4" plywood we used for the back. We made it 48" tall and 24" wide. I finished it with a charcoal grey water based Minwax stain, and then sanded that out to bring out the wood grain more. I topped it with two coats of wipe on poly, also by Minwax. It was not too hard to build and was pretty fun actually. I am just glad that it actually looks like a piece of furniture and not some boards screwed together. I kind of want to do one with red stain now to make it look like barnwood, hmmm...

This is my latest project and my first project post on my new blog. I've included some step-by-step photos on my blog. I'm using this kitchen island as a craft cart in my craft room. This project was so fun and easy to put together. I love how it turned out!

we took Ana's plans and modified them to fit our space. I ended up routing the edges of the 1x3 and 1x2s for the door and drawer fronts to give more definition between the boards to help with the illusion of seperate drawers. I absolutely love how this turned out!