Community Brag Posts

Decided to make a pair of nightstands! Made them a few inches less wide than the original plans and adjusted the height to match my bed. For the first one, I went with the drawer as-is from Ana's plans, but for the second I got brave and used actual drawer runners from the hardware store. It wasn't as hard as I was afraid of; I just reduced the width of the drawer to account for the runners and used a false front so I could attach the drawer front in the right place.

I had so much fun with this! I followed the plans exactly and made up the nightstand as I went along.

I have used 1/2 inch thick plywood, 2x3 instead of 2x2, and 1x3. I don't have any miter saw or table saw. I used hand saw (comes with miter box) and circular saw to cut all the materials. It isn't perfect but I like it.

I built this Family Picnic Table for my brother and sister in law for their river house for Christmas.

I started this the first week of October this year. Cutting lumber, priming, painting and assembling at my home two hours away. 

I disassembled it, loaded it on a trailer with my tools and drove it to their home. This is where I needed two people to help get everything up on the second floor deck.

The plans were great! I am placing a link to 2 photos of the finished product.

I told their kids to buy an umbrella for them for Christmas - Carlton Lowry

This was my first wood project, and I LOVED doing it!!! Now I'm addicted :). Thanks so much, Ana, for the amazing plans and inspiriation!

This is my second project.  I sanded, primed, painted, sanded to distress the paint, then stained the whole thing just long enough for the stain to soak in to the sanded spots (5 minutes or less), then wiped it off. 

Pottery barn inspired tv media center and matching dresser.

We needed an accent table for our hallway and this simple table was perfect. I cut all the pieces in about an hour the night before and spent approximately four hours building the table the following day.

B-day present for my niece 

Full Instructions HERE

What you will need to build this DIY Welcome Post:

1. 4 x4 Fence Post Cut: 30 inches long 1×6 down to make 2 5 1/2″x5 1/2″ squares and 2 4 1/2″x 4 1/2″ square.
2. Different Widths of wood cut into squares. For the three tear welcome post I have 3 different sized squares. They measure: SMALL: 5 1/2 by 5 1/2 inches MEDIUM: 7 1/2 by 7 1/2 inches LARGE: 9 1/2 by 9 1/2 inches.
3. Single Hook
4. Long wood screws & Drill
5. Stain
6. Rust-Oleum Varathane Outdoor Classic Clear Water Based Spray, Gloss Finish
7. Wood Glue
8. Orbital Sander or some muscle & some sand paper
9. Wood filler (not required)

Full instructions on how I put this together on my blog.

This was SUPER easy and I love it. My daughter wants one now so digging through my scraps is what I will be doing tomorrow. Thanks Ana!

Built this table 11 feet long with live edge sinker cypress. Hand rubbed 12 coats of tung oil, then finished with Waterlox satin.

Found the old Home Depot plans, and decided to add my hand burned touch to it.
Have seen some that were using vinal or painted letters, but i like the burned effect, and its easier to seal right over the top with the outdoor stain/seal treatment..

What a great easy project. The wood was really inexpensive. The only pricey part was the fabric.

A 36" sink base is the center, flanked by two 18" cabinets made by modifying the 21" base cabinet plan.

Here are some of the more structual photos to help people along the way. 

I did the head board and foot board using the directions. I used 2 4.5 inch screws on each 4x4 post to secure the 4x4s to the head board. 

I used 2 4.5 inch screws to secure the head board to the frame. 

I used some brackets I had lying around to secure the footboard to the frame. 

I used 0.5 inch partical board to put on top of the frame I put the joists down 0.5 below the side rails so the partical board would sit down and inside. 

I used 2x6 boards for the frame with deck brackets to secure it. 

I used left over wood from the 4x4 to be cut 10inch each and 2x6 study 3 of those 4x4 to lift the frame up.

for the fourth raiser I used left over wood from the 2x10. 

I primed the wood and painted white. 

Hopefully these pictures help. 

All said and done it was close to 500-600 to build. I did this in Canada where materials can be a little pricier.