Community Brag Posts

We absolutely LOVE this clubhouse bed. Not sure who loves it more, my litte boy or his parents! My husband has zero wood working skills, but his dad has a few wood working skills, so together they made this happen. We bought half of the lumber-cheapest whatever we could find, and my father -in-law bought the other half -the much more expensive stuff. We probably could have made this around $150-$200 using all the cheap stuff. We added a window box to hold little super heros and a shelf on the opposite window, we also added a shelf half way up on one of the post at the bottom to hold a lantern. We raised the bed 4 inches higher to give more room at the bottom. We used ply wood for the bottom of the bed rather than slats. We used a cherry 223 Minmax -1 coat and then put a clear coat on it.

This was my first build of this Rustic X Coffee Table and I really liked how it turned out! This one was modified to 43" long, same height and width. I love all the Rustic X pieces in this collection! They have been a favorite.

I finished the table using black tea, steel wool and vinegar, followed by Minwax's Dark Walnut stain and topped off with a Satin oil-based Polyurethane.

To see my other projects, make sure to visit my facebook page (only after you have spent enough time on Ana's site!)
www.facebook.com/simplyrustik

Needed a small table for the nursery and this was perfect! 

You were right, this really was super-easy and super-cheap!

Based this wagon on plans found on Ana White's site. I built this for a 2 year old girl of a co-worker. She is right now using it to pull around her dolls.

Sliding barn door tv console. Created the metal hardware from aluminum i bought from home depot ($80)

My first project besides some simple shelves. I wanted to use old sturdy wood I had from parts of a bed so I used the ana white plan but improvised quite a bit. I also accidentally made it much higher but like it this way. I am going to paint it a deep bright greek blue in the spring. I am happy with it!

I built this closet system for our basement gym as a Christmas present to my boyfriend.  He loved it!

I stained all of the boards before building as suggested in the plan - it definitely saved a lot of time and stress.  After cutting and staining, and I brought all of the pieces downstairs to build.  

The actual building went relatively quickly, but without perfectly straight boards, the shelves themselves were a little tricky.  I also just nailed the shelf boards down with wood glue rather than screwing them in to save time - it's still sturdy and secure.

The length of the closet is about 8 feet long, so the middle shelf is about 1 foot and the two rod shelves are about 3.5 feet long.

This was pretty easy and inexpensive to make.  I'm going to make the coffee table this weekend, but converting it to a chest with a lift top.  Purchased some cantilever hinges for that on Amazon for about $35.  Will post pics of that once it's done.  Sorry the photos came out sideways....They keep uploading that way even though they are right side up on my iPad......

Easy Peasy!

Materials & cost: Framing grade pine and 1x3 furring strips. $110 including finish materials.

I used some of the excess 2 x 6 that I had left over to make the feet square instead of just using 2x4s like in the plans. just cut them to the same length as the 2x4 feet, then butt them up against the 2x4 feet and mount them to the frame.

Also, I made the support beam removable by using face-mount 2x4 joist hangars to hold it instead of bolts.

Total build time = less than one week

Next project will be a custom headboard for it..

I followed the plan for making the shell of the house, but since I have access to help and the on-post woodshop I made a few changes.  We cut a 2x4 to fit the doorway, and then used the lazer cutter to make the panels, after sanding and painting, I used a necklace bead as the doorknob.  We also cut some 1" square blocks and drilled the center, the used the grinder to round them out to make a holder for the dowl curtain rod.  I also used scrap frame wood for the window/door trim.  Then I covered the entire house in wallpaper!  The outside is a brick wallpaper, the inside is a gray/silver with sparkles, and the ceiling is white with sparkles.  I used cork for the floor so it would be soft and warm feeling.  It took me a long time, but I am very happy with the results.  My daughter was thrilled to recieve this on Christmas morning!  

Built a pair of these for the master bedroom as my first project... Not too bad, very functional, and I was able to use mostly wood I had laying around...

I saw Ana's tilt trashcan plan and I knew that I had to tackle this bad boy. I didn't want anything stationary because my 1910 kitchen is big but also pushed against the walls. My stove is 7 steps from a counter top so prep is kind of a pain.

I modified Ana's original plan to be taller and even (well, close) with the stove's height for extra counter space. I also wanted a slide out cutting board with a hole so that while I'm chopping my ingredients, I can scoop it into the hole that drops directly into the trash.

I'm a very ambitious girl who doesn't like to be told that I can't do something. This is also my second built....my first is a huge craft supply cabinet made from old barn wood that is lovingly referred to as 'The Outhouse'. My tools are limited to a 7in circular saw, drill, and Kreg Gig. I knew this would be tough but after a few head scratches, I have a pretty cool island.

If you have questions about what I asked, please ask. There are all types of wicked little tricks/fixes in this beast.

We made this bed in the king size. DEFINITELY sand each shim prior to gluing it down. It is definitely no fun rolling over in the night and hurting my hand on the rough shims. I would also recommend staining the headboard (the base for the shims) prior to gluing down shims so that any holes between shims blend in with the stain color underneath. We did not and there are a couple spots that you can see the plain wood under the shims. Also, we did what they recommended in the plans to secure the side rails. The bed is not very stable and squeaks. We keep talking about altering it somewhat, but it's so dang heavy that we have been putting it off. One other thing that I wish we had done would have been to sand off the corners of the end of the footboard. We've gotten a few bruises from walking into the ends. It cost more than we expected and it took longer. But overall, we love it and are very happy with it. Just wish we had known now to do some things differently. 

changed the dimensions some but thanks for the inspirations!  

I needed a new laundry system, and thank goodness I found Ana White's projects on Pinterest! I incorporated the laundry sorter and added casters to the bottom as well as a paper towel roll on the side since it is next to the sink. I also used a modified version of the washer/dryer platform into my space. It does not have the bottom platform and the 4x4's are inside the 2x4's and attached to the platform as well as the 2x4's. Sterilite makes organizer drawers that fit exactly in the opening of under the platform. And, voila! New colors, new organization, new light bulbs :0), new laundry room!