Community Brag Posts

Plans from Wood Parsons End Table with Bottom Shelf.

24Lx24Wx21H

After clearing some doesn't-belong-here furniture out of my living room, my coffee table became the home to our stereo receiver and HTPC. This project was about getting my coffee table back, in a quick, inexpensive way. The photos *still* don't do justice, but since I've added the equipment, I am SO not hauling this back outside for glamour shots.

Size: Adjusted to fit under a wall-mounted flat TV:17.5"D x 21"H x 42"W. The adjustment was simple: use 5 2x4s instead of 4.

The photos also make the stain appear darker than it is -- it's truly a rich teal. I love the color so much, I'm going to strip my built-like-a-tank, 65-year-old wooden front door and stain it, too.

This is my first "real" project. I've built things before. Badly. Now, I have a Kreg, and I'm learning to be a little more patient with clamping and squaring for better results. :)

It appears that my next project will be the taming of the cable spaghetti.

This was such a fun project. Had to figure out how to build the sliding door HW. I didn't want the doors flying off when sliding so I did secure in a way that didn't limit the aesthetics or function. I did add a back to the cabinet since the picture was taken. Strips of plywood to give it that barn flavor. The most time consuming part was painting, staining, protecting and waiting for it to dry.

This is my first project for my little girl! We bought the common boards at home Depot where they cut them to length. I spent about $55. I used a small wood saw to cut the required angles and sanded the edges with a sanding block. I'm happy with the result even though I didn't use the wood filler or stain (yet).

After building the playhouse loft bed, I found this project to be very easy. I built the bunk beds at 37/38 weeks pregnant, so that should tell you how simple it is to construct. The total cost came in under $300 and I was able to use some of the scrap wood I already had in my garage.

I did run into some trouble with the slanted ladder. Even though the pieces were cut to the exact measurements in the plan, the sides of the ladder were too short for the bed. Being very pregnant and impatient, I just modified the ladder so I wouldn't have to waste the pieces I'd already cut.

You may also notice that I didn't fill and sand my pocket holes on the end pieces yet. That was also me being very pregnant and impatient. I'll go back and do that later when I have more time. Despite the little bit of finishing work remaining, this was pretty much a 2-day project. Cutting and construction was fast (one day) and finishing took another full day.

I used Valspar "Blue Burst" paint from Lowe's to finish the bed. I used bolts to attach the side rails because we move frequently so I wanted the bed to be easy to disassemble. Overall, this was a very easy and fun project!

This is a simplified version of the Unabox from Make Magazine.

Build Instructions:
http://www.instructables.com/id/Puzzle-Box-Unabox/

Video:
http://youtu.be/VTaoUHsGau8

If you like this, please see my other puzzle box.
http://www.instructables.com/id/Puzzle-Box-4/

Overall this took about two weeks for me to build and finish. We modified the original plans to make it larger to accommodate a computer. It is 76" long, 30" tall, and 22" deep. We also had to customize it so we could fit it around our fireplace because space is limited in our house.

These were made from scrapwood.

The table and bench project were awesome. I got a lot of inspiration from these, and have built 4 table so far. After posting the first one on Facebook, everyone wanted one. The one thing I would recommend is to really pay close attention to the lumber you're buying, make sure it straight and the edges are not chipped, to ensure all yourights seams match up, and your project ends up square.  A tip to alleviate all this,  is to buy everything wider than you need, and rip it straight through your table saw. What I mean is, if the table top calls for 2x10's, then buy 2x12's instead, and rip them down to 10 inches, so you're seams match up perfectly.  It may cost a tad bit more, but you will definitely be happier with the end result. 

Needed cabinet for trash and recycling, so modified the plans to fit under the existing counter top.

I build the bar table with an x-base and created some stools using part of the plan. We really wanted backs on the stools so I made them up!

This was made from scrap wood, a cheap $5.00 mirror and some hooks. This hangs near my front door and I hang scarves and bags on it. Always good to have a mirror to double check yourself before you leave the house. It was based on Ana White's Craftsman Frame.

Capped railing and head/foot board for a different look. Did not like the look of the carriage bolts so sunk those in and used buttons to cover. Modified slope and added hooks to ladder so we could remove to vacuum etc. Would of added one more step if I were to do it again. My guys are little so added railings to back side top and bottom and extended railings.

This is my very first project. Never used a saw before until a few weeks ago. I am really happy with the way it turned out.

I shortened the plan and modified the second shelf. I was planning on an "X" brace for both sides but got carried away and realized it wasn't going to work on the one side. I like the end result and don't mind that its missing.

I would have finished it sooner but was a bit intimidated by the angled cuts. My miter saw only cuts 45.