1. Home
  2. Plan Catalog

Turned Leg Farmhouse Table

The free plans on this website are made possible with advertising and affiliate links.  Thank you for helping us keep plans free.

 

|save this plan
Turned leg farmhouse table with bench
Difficulty
Intermediate
| Print this plan

Build a farmhouse table with turned legs! Free plans from Ana-White.com

turned leg
tabletop
under table with farmhouse bench
table with bench

You have been asking for a Farmhouse Table with turned legs plan for years now. One of our kind readers, Patrick Hosey volunteered to build a farmhouse table with turned legs for you.  And he worked with Gabriel Gallant to create a video of the story behind building.  

This video was created by Gabriel Gallant with music by Patrick Hosey.  Thank you Gabe and Patrick for the beautiful video.

The beautiful table legs are contributed from Osbourne Wood.

Dimensions
dimensions diagram of farmhouse table with turned legs
Dimensions are shown above.

Preparation

Shopping List

4 - Portsmouth Large Dining Table Legs from Osbourne Wood

4 - 1x10 boards @ 8 feet long (save scraps to use for benches!)

2 - 1x4 @ 8 feet long

1 - 1x3 @ 8 feet long

 

Common Materials
1-1/4" Pocket Hole Screws
Elmer's Wood Glue
Elmer's Wood Filler
120 grit sandpaper
Cut List

2 - 1x4 @ 24 1/2"

2 - 1x4 @ 66"

2 - 1x3 @ 30 1/2"

4 - 1x10 @ 78" Angle supports cut from scraps

Tools
Tape Measure
Speed Square
Pencil
Safety Glasses
Hearing Protection
Kreg Jig
Drill
Circular Saw
Power Sander
General Instructions

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!

Instructions

Step 1

Build your tabletop first. Set aside on a flat level surface to let dry.

Step 2

Next, build your end aprons/leg pieces.

Step 3

And then simply connect with side aprons.

Step 4

Add center supports.

Step 5

Finishing Instructions
Preparation Instructions
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth.

It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
Project Type
Table Plans
Dining Table Plans
Room
dining room
Style
Farmhouse Furniture

Comments

bhoppy

Thu, 05/24/2012 - 11:44

For many reasons... I thoroughly enjoyed watching all the steps and tools you used Patrick! And the video was beautifully shot and edited:-) Loved the shallow depth of field close ups!

whitney_smith

Thu, 05/24/2012 - 13:11

Having already built a table almost exactly like this one, I know just how much love goes into it. This video beautifully captured that passion between woodworker and wood.

birdsandsoap

Thu, 05/24/2012 - 14:12

Amazing Patrick!

This is a such a great video, it is done so well. I loved watching the table come together, but then I got lost in the music! Music by Patrick Hosey?! You truly are the jack of all trades.

The table turned out beautiful, and as I was watching your video, I kept thinking, "There's that router table and miter saw cart that I want sooo bad!"

Nice job. I really enjoyed the video and transitions, and the music was so calming....now I have to go build something!

tracysmith

Thu, 05/24/2012 - 23:52

I just posted a comment about the same thing before I even read any of the others! I did the same thing watching his video... I want that router table! Too funny!

patrickhosey

Thu, 05/24/2012 - 15:36

Thanks for all the nice words. This was a very fun project. Thanks to Ana and Gabe for making it happen. Here are a couple things to google after watching this video.

- How to joint boards for glue ups.
- How to glue up large table tops.
- Beadlock joinery
- TableTop Fasteners and Hardware and what it does

There are so many ways to do things, just find a way that you like

Maybe we should do some more shop furniture next time.

birdsandsoap

Thu, 05/24/2012 - 15:52

I've never seen those fasteners from Rockler before, I'll have to check those out. And the joinery too, I've never seen that type of jig...so much I don't know about, but it's fun to learn!

I "Second" the nomination for more shop furniture! *ahem* router table.

Rick S (not verified)

Thu, 05/24/2012 - 19:28

Can you provide a link to the legs used in the table? Thx.

patrickhosey

Thu, 05/24/2012 - 20:37

There's a link on the materials list. It looks like just bold black text but it's a link.

dananryan

Thu, 05/24/2012 - 17:26

Great video and table. I second birdsandsoap. More shop furniture would be awesome! Especially the router table...

SarahM (not verified)

Thu, 05/24/2012 - 19:47

Hello,

I love this table. Thank you so much for such detailed instructions. Would you mind sharing what stain you used for the table top?

Thank you in advance.
Sarah

tracysmith

Thu, 05/24/2012 - 23:50

This was AMAZING!!!!!!!!! I loved the build, the table was beautiful, but the video was spectacular. In it's simplicity, the music, the way it was edited. I loved it! It encapsulates what I experience sometimes when I'm out in my garage turned shop building. Just creating, just being. There's almost something spiritual about it for me. I do my best thinking out there ;-) I also got really hung up on your amazing router table and miter saw table.... did you build those as well and are you planning on sharing those plans with us? ;-) I have been scouring the web looking for a good router table design, still haven't found one that I really liked until now.

Excellent work! Please, keep those videos coming, very great!!!!!

SarahM (not verified)

Fri, 05/25/2012 - 05:17

Hello,

I love this table. Thanks for the great instructions. Would you be able to share the kind and color of stain you have used on the table top.

Thank you in advance,
Sarah

SarahM (not verified)

Fri, 05/25/2012 - 05:19

Thanks Patrick and ignore the repeated question I thought the first one didn't go through.

Cheers,
Sarah

deannaf

Fri, 05/25/2012 - 07:49

Patrick that was an amazing video and the table looks fantastic. I like others who have commented am really interested in your router table, is that your own plan or are you able to share where you got the plan from.

Your little one is gorgeous too by the way, what a cutie.

Aisha_ (not verified)

Fri, 05/25/2012 - 07:56

Beautiful video and beautiful table Patrick! So inspiring watching stuff like this. I love the tool you used to make those...are they biscuit joints? Anyway, where did you get it from? And the idea of making shop furniture sounds like the greatest. I would also love plans for a router table!

Kathyy (not verified)

Fri, 05/25/2012 - 10:32

Another reason you make furniture is because you are great at it. Love your blog and all the wonderful projects you make.

claydowling

Sat, 06/02/2012 - 08:47

I've never seen that particular style of loose tenon and jig before. I've either hogged it out with a drill and cleaned it with a chisel, or gone old-school with a mallet and mortise chisel. That looks like a good option for low labor, low cost.

Watching you work with the spray gun just convinces me that I need to get back to experimenting with mine again so I can master it. Or at least become something resembling competent.

patrickhosey

Sat, 06/02/2012 - 12:54

That jig is called the beadlock loose tenon jig. It's awesome. Very fast. You're not supposed to have to clean the mortises out because the tenon stock comes fitted to the mortise. But what I found is that they fit so tight that there wouldn't be any room for glue in there so I clean them up a little. The pocket screws were just to add clamping pressure without a clamp.

Also I'm nowhere near mastering the spray gun yet. What a weird world that is.

Patrick

Guest Chris (not verified)

Sat, 06/16/2012 - 12:36

That was so neat! I want to try something like this but have been so intimidated just thinking about it. You make it look totally manageable and I'm gonna go for it!

TeeTee (not verified)

Wed, 08/15/2012 - 11:50

I love the table! I'm gonna try to build this for my kitchen. Is there a way to make a leaf in the table or something? Bcuz the current size is too big for my kitchen. So I would like to make it smaller, or be able to remove a leaf and add it when I need to.

Billie (not verified)

Mon, 09/24/2012 - 13:46

I, too, would love to see this plan with a table leaf or two. I have a family of four, but love to have guests over for dinner. The ability to go from a 4 or 6-top to an 8 or even 12-top when needed would be amazing!

Thanks so much for all that you do!

Patrick Hosey (not verified)

Sun, 10/07/2012 - 07:12

If you make all 4 aprons the same size, you'll get a square without even trying.

Sugarman (not verified)

Thu, 10/11/2012 - 09:52

I wanted to make a ten foot table using furniture grade plywood as the tabletop. Also not having a mortise and tenon jig but having a dowel jig how would that change the equation? Thanks

patrickhosey

Thu, 10/11/2012 - 09:58

You can use furniture grade plywood no problem. You just have to mask off the edges. It's totally up to you but I would avoid using edge banding on a table top. It would just be super cheesy. Again that's your choice though. You can totally use a dowel jig to do the same thing I did using the tenon jig. If you have a kreg jig then you can mix the two as well. If not, you'll need some long clamps.

Sugarman (not verified)

Thu, 10/11/2012 - 17:24

I plan on putting some kind of molding on the edges. i have a nailgun and compressor so it will be a cinch. I also have a kreg pocket hole jig. It is a great tool. Pocket hole versus dowel, which would you recommend? Also your table is 8 feet long. Do I have to modify the plans at all to go to 10 feet? Maybe add another crosspiece?

Sugarman (not verified)

Thu, 10/11/2012 - 17:36

Also any recommendations for the wood I use? Oak has a bolder grain which doesn't really work because i am going for a more refined look. I mostly work with maple. That should be fine, no?