When a new baby comes along, it's not just the baby that you have to make room for in your lives. A baby also requires a large amount of things. And these things often don't fit into tradditional storage systems. This nursery armoire is designed to organize all of the baby's things, keeping necessities in one spot. Special thanks to Jake for sharing his amazing armoire with us.
Pin For Later!
2 – Sheets of 3/4″ MDF or 3/4″ A1 Plywood 1 – Sheet of 1/4″ MDF, Lauan, or plywood (for the back) 1 – 1/2 sheet of 1/2″ MDF or A1 Plywood (for the doors) 3″ Cabinet Screws (About 50) Wood Filler Wood Glue 2″ Nails 1 1/4″ Nails 5/8″ Nails (for the cabinet doors) 3 – Sets of Full Overlay Frameless Door Hinges 5 – Sets of basic hinges 1 - 8′ stick of 5 1/4″ base molding, like this from Lowes 3 – 8′ sticks of 1/4″ x 2 1/2″ hobby boards in desired species (you may wish to take the cut list in and get exact cuts to pay by the foot instead of by the board)
Cut List for the Box 1 – 1×24 @ 6 1/2″ (Drawer Divider) 2 – 1×24 @ 66″ (Sides) 4 – 1×24 @ 38 1/2″ (Shelves) Cut List for the Trim 1 – 1×4 @ 40″ (Top Header Trim) 2 – 1×3 @ 26 1/2″ (Bottom Side Trim, Fixed) (cut at 62 1/2″ if you want the top trim fixed too, for non-flat folding doors) 2 – 1×3 @ 36″ (Top Side Trim, if you choose to have the flat folding doors) 2 – 1×2 @ 35″ (Shelf Trim) 4 – 1×2 @ 24 1/4″ (Side Crown Trim) 1 – 1×2 @ 41 1/2″ (Bottom Front Crown Trim) 1 – 1×2 @ 43″ (Top Crown Front Trim) 2 – 5 1/4″ Base Moulding, @ 25″ (Longest Points, mitered out on front end) (measure to fit) 1 – 5 1/4″ Base Moulding, @ 41 1/2″ (Longest Points, mitered on both ends out) (measure to fit) Cut List for the Doors 2 – 1/2″ Sheet Goods @ 35 3/4″ x 17 1/4″ (Back of top Doors) 2 – 1/2″ Sheet Goods @ 19 1/2″ (Back of bottom Doors) 8 – 1/4″ thick x 2 1/2″ wide hobby stock @ 17 1/4″ (Top and bottom trim for all doors) 4 – 1/4″ thick x 2 1/2″ wide hobby stock @ 30 3/4″ (Top Sides, cut to measurement) 4 – 1/4″ thick x 2 1/2″ wide hobby stock @ 14 1/2″ (Bottom Sides, cut to measurements) *Cut your doors slightly smaller if you are using edge banding to finish edges of doors. Shopping List for Drawers Scrap 1×24, or matching width to the box from the armoire, 3′ or 2 18′ pieces 2 – 8′ 1×6 Boards 2- Sets of Undermount Slides Optional Drawers Cut List 2 – 1×24 @ 17 7/8″ (Bottoms) 4 – 1×6 @ 17 7/8″ (Fronts and Back) 4 – 1×6 @ 22″ (Sides of Drawers)
Work on a clean level surface. Have someone help you rotate and move this project, it’s going to be HEAVY. To decrease expense and weight, you can use a 1×16 or even a 1×12 board width instead of the 1×24. The 1×24 is designed to fit the older TVs. A 1×16 would still be enough room for a hanger to use this as a closet. When working with MDF, predrill the entire length of the screws shaft and use special MDF screws or drywall screws. Do not use wood screws. Always use glue and mark out your joints on both the joint and the outside to assist with build. Take a square after each step. Use proper safety equipment.
Drawer Divider. Take tow of the shelves and mark 18 7/8″ inch in from the outsides. Then fasten the divider in place as shown above. This divider is not just for the drawer housing. It adds strength, helping your shelf carry a heavier weight. If you plan to use this as a computer armoire and would like to add a keyboard tray, you can omit this divider, but the shelf will not be as strong. In the next step, you will attach the sides.
Begin Trim. Start with the header trim. Fasten in place with 2″ nails and glue, to both the top and sides. Then fasten the bottom side trim, also to the sides and shelves. Finally, measure and cut the blue trim above from 1×2 boards, and fasten in place with 2″ nails and glue. Keep edges flush with the tops of the shelves.
Top Side Trim for Fold Flat Doors. Measure and cut the side trim, approximately 36″. Using framless full overylay hinges, fasten the trim piece in place. The trim will need to extend out 90 degrees when opened. You can use euro style (needs a special bit to install), but there are also other types. The important elements are FRAMLESS, FULL OVERLAY and opens 90 DEGREES or more.
This drawer is designed to work with the flat folding doors. If you choose to have non-flatfolding doors, you will need to cut your drawer bottoms and sides @ 15″.
Build your Drawers by fastening with glue and 2″ nails the fronts and the backs of the drawers to the bottoms. Then fasten the sides in place, with glue and 2″ nails, to both the bottom and the sides. Mount in the openings using undermount drawer slides.