1. Home

Community Brag Posts

Lighted Saltbox House

My wife went shopping one day in a primitive furniture shop and found this saltbox house that she loved. So I decided to get a picture of this house and build it myself. This project was a lot easier than I thought it would be. Hope you enjoy.

Estimated Cost
$18.00 for wood and left over paint sitting around.
Estimated Time Investment
Day Project (6-9 Hours)
Finish Used
One layer of black paint, covered with one layer of cream paint, distressed and clear coated.
Recommended Skill Level
Beginner

Comments

candrea1402

Sun, 08/12/2012 - 13:45

Love this one could you possibly give me the dimensions ? would love to try building this

Rustic X End Table

Submitted by Tonyjoe on Wed, 01/08/2014 - 08:45

This table was my 4th build from the site and took my wife and I about 10 hours to build.

Built from Plan(s)
Rustic X End Table
Estimated Time Investment
Day Project (6-9 Hours)
Finish Used
Minwax classic gray finish
Recommended Skill Level
Beginner

Modified Grandy Sliding Door Console

I made my console a little shorter (71 in). I used reclaimed wood for the exterior and sanded/stained wood for the shelving and doors. I used screw eyes and galvanized pipe for the sliding door hardware. A lot of fun!

Built from Plan(s)
Grandy Barn Door Console
Estimated Time Investment
Week Long Project (20 Hours or More)
Recommended Skill Level
Beginner

Comments

paolans12

Fri, 08/12/2016 - 09:15

It looks beautiful, do you have plans ?? would you mind sharing them ?? It'll be my first project ;)

Rustic X Bench for Entry

Made 2 changes to the plans which was using a 2 x 4 as a center top board to add some variety to the board width and also decided to go with breadboard ends which also used 2x4

Thanks for the plans!

Built from Plan(s)
Rustic X Bench
Estimated Cost
$50
Estimated Time Investment
Afternoon Project (3-6 Hours)

Adirondack Chairs with Foot Rest

Submitted by Anonymous (not verified) on Sun, 07/30/2023 - 14:45

Great set of outdoor chairs with foot rest!

 

RG Design & Build

Built from Plan(s)
Modern Easy Build Adirondack Chair

Comments

Channing cabinet/desk

Submitted by mactanya on Mon, 03/19/2012 - 17:57

Well, this was a project that was running concurrently with the Benchright coffee table and I finally got it installed along with the walnut stained 1x4 pine desktop. At first (due to inexperience) I stained it and since I had the wrong plywood, it looked horrible. So it got bondoed and painted and converted into a drawer/rollout printer drawer/hanging file drawer and a support for my single piece 12' + desktop.
By the way, its a pain in the butt to keep the cabinet square and I worked it and worked it, believe me.

Blog Link
Channing file cabinet
Built from Plan(s)
Desk with Drawer and Shelving
Estimated Cost
$100 tops
Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
Sherwin Williams Alabaster (gives it that aged white look) and minwax polycrylic.
Recommended Skill Level
Beginner

Comments

panthajds (not verified)

Mon, 01/21/2013 - 18:10

I was wondering how you made the desk longer. I have an 11 foot wall and i want the top desk to span the whole wall i was wondering how you supported the whole desk, did you need to add any extra supports?

Hemnes linen cabinet finished!

Submitted by Crzymedic on Thu, 01/09/2014 - 16:29

This was my first build for Katy and she loves it! We used acrylic glass and used the frosted spray pains from krylon.

Built from Plan(s)
Hemnes Linen Cabinet
Estimated Cost
$150 plus what king of panel you use
Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
white paint.
Recommended Skill Level
Beginner

Comments

Double Vanity

Submitted by krmoon81 on Thu, 03/31/2016 - 22:30

Well to make a long story short I started out just replacing an old tub in the bathroom which turned into a whole remodel!! I’m talking new toilet, floor, lighting and heck while I was at it lets knock down a wall and make some room for a double vanity. After all in a few years three teenage girls  will be fighting for sink space!!! Honestly I just didn’t want to spend $800 - $1,000 on a double vanity so I decided to take matters into my own hands. This was my first time building any type of functional furniture. I made a ton of mistakes but I also learned many valuable lessons. I really took my time....about 3 weeks...ok, maybe 4. Building this vanity was like cutting 101 for me. #1 lesson I learned, MAKE SURE YOUR CUTS ARE STRAIGHT!!! I also learned the value in test cuts and having a lot of patience and extra wood on hand. Anyone can do this, just be willing to put the time and effort in…and do lots of research.

Built from Plan(s)
48" Turned Leg Vanity
Easy Frame and Panel Doors
Estimated Time Investment
Week Long Project (20 Hours or More)
Finish Used
Paint
Recommended Skill Level
Beginner

Comments

TV Console

Submitted by J. Davis on Fri, 11/29/2019 - 17:24

I used the Grand Barn Door Console plans to build my wife an entertainment center. Instead on the "barn doors", I framed them out and attached a patterned sheet metal, from the back.

Built from Plan(s)
Grandy Barn Door Console
Estimated Cost
200
Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
The base has 3 coats of white furniture paint. The top was sanded down to 120grit, stained, and polyed.
Recommended Skill Level
Beginner

DIY Outdoor Furniture Set

Submitted by Anonymous (not verified) on Fri, 08/04/2023 - 11:32

Loving this furniture! We modified it slightly by raising the height of the couches. Added some height and a slight tilt in the back. The chairs are super comfortable as the plans are done. We used 6” 25x25 cushions. We plan on staining soon.

Jaime Sallis

 

Built from Plan(s)
Outdoor Sofa - Modern Comfort Collection
Outdoor Chair - Modern Comfort Collection
2x4 Outdoor Coffee Table

Comments

LeeEspinoza

Mon, 11/18/2024 - 03:28

Building your own furniture is such a satisfying project, especially when it turns out looking exactly how you imagined. I’ve always loved the idea of DIY outdoor pieces, but let’s face it, sometimes it’s hard to tell which materials or designs are worth the effort. I found that reading up on others' experiences can save a lot of time and mistakes. That’s when I stumbled upon 1stopbedrooms reviews which gave me some solid insights into what works and what doesn’t when it comes to furniture that’s both stylish and durable. It definitely helped me refine my approach and led to a pretty successful DIY outdoor furniture set!

Seasonal And Holiday
Spring
Summer

Ten dollar ledges

Submitted by Spolitte on Wed, 03/21/2012 - 20:50

Here are a few of the ten dollar ledges we added around the girls bed. We had no room for tables so we thought we would give this a try. It's working beautifully. We hung the ledges in studs and they are standing up to constant use perfectly. The girls have space for their most cherished nik naks and a drink in case they wake thirsty in the night. We couldn't be more pleased. Now I'm seeing the possibility for ledges in every room.

Built from Plan(s)
Gallery Ledge Shelves
Estimated Cost
6.00 minus the paint.
Estimated Time Investment
Afternoon Project (3-6 Hours)
Finish Used
No voc semi gloss for easy cleaning
Recommended Skill Level
Beginner

Comments

garryh (not verified)

Thu, 04/19/2012 - 19:01

If converting existing floor space into a half-bathroom, such a renovation can cost as little as a few thousand dollars, making the addition of a powder room one of the few home improvement projects where the value added to the home exceeds the cost of the renovation.water damage Pearland tx

hannah22 (not verified)

Sat, 04/21/2012 - 00:28

Before you go to use it...if it's been sitting for awhile...give it a good shake. As you can see in this picture...it does tend to separate a bit. But after a quick shake it's good to go. To use: spray on stains as you normally would. I usually let mine "soak in" for a few minutes at least. Then launder as usual.water damage Temecula CA

bobp22 (not verified)

Fri, 05/18/2012 - 19:54

I used to be more than happy to seek out this internet-site.I wanted to thanks in your time for this glorious read!! I positively enjoying each little bit of it and I have you bookmarked to check out new stuff you weblog post. Water Damage Anaheim CA

peak22 (not verified)

Fri, 06/01/2012 - 04:59

Quite insightful submit. Never believed that it was this simple after all. I had spent a very good deal of my time looking for someone to explain this subject clearly and you're the only one that ever did that. Kudos to you! Keep it up. Water extraction Lakeline OH

kim22 (not verified)

Sun, 06/17/2012 - 20:37

I'm so excited that I have found this your post because I have been searching for some information about it almost three hours. You helped me a lot indeed and reading this your article I have found many new and useful information about this subject. Paint Contractor Glendale AZ

milep (not verified)

Mon, 07/16/2012 - 22:55

The program is designed under the same model as new homes built for Habitat families where the veteran will repay the zero interest loan necessary for these repairs, which is then deposited into a revolving fund to assist additional families in need of decent housing. Mold Inspection Covington LA

ricky17p (not verified)

Wed, 08/01/2012 - 22:13

If you're involved in a head-on crash, the windshield must stay in place to keep you inside the car and to keep flying debris out. If the windshield flies out, so too may you or your kids. Improperly installed windshields can easily be dislodged during a crash. Architectural Engineer NYC

ricky17 (not verified)

Fri, 08/17/2012 - 06:48

You have to put efforts in home maintenance to make sure everything is in right condition. If any part of your house needs repairing then have it repaired immediately. If you neglect the problem for too long then it might become even more complicated. Masonry contractor West Hartford CT

ghikh (not verified)

Tue, 11/20/2012 - 00:17

This is represented partly in the significantly higher frequency and register neutrality of connectives such as tak or totiž when compared with the English so and therefore but primarily by the nature of the mental spaces set up by the Czech lexemes. water damage Anaheim CA

Waylanderman (not verified)

Fri, 11/30/2012 - 03:19

The contemporary strategy is often focused on the development of specific skills and abilities. As a result, it fails to provide with the broader education and, instead of the formation harmonious, balanced personalities, it breeds specialists trained to work in a specific field. This is a good example like the ones http://bestsamplepapers.com does. People prefer more broad basis.

Hailey Platform Bed and Kentwood Bookshelves

Submitted by kjw003 on Sat, 01/11/2014 - 16:31

Built the Hailey Platform bed with planked headboard, and two Kentwood bookshelves, for a guest room in our new house! The dimensions of the bookshelves were changed a bit to fit the space, but the bed (should be) built to dimensions in the plan for a full size bed.

Built from Plan(s)
Hailey Planked Headboard
Essential Platform Bed Frame
Rustic Bookshelf Plans with 2x2 Face Frames
Estimated Time Investment
Week Long Project (20 Hours or More)
Finish Used
Stain was apple cider vinegar vinegar and steel wool mixture. Sealant used was Vermont Natural Coatings Polywhey furniture finish (satin finish).
Recommended Skill Level
Starter Project

Study Desks

Submitted by rosiejane on Sun, 04/03/2016 - 21:54

I built a desk each for my son and daughter. They got to choose the type of base. I used old bed slats 90x45mm (4x2) salvaged from verge ripped in half for the bases. I used 12mm plywood for the tops. 7mm ply for the shelves on the sawhorse leg version. Unfortunately, despite getting the straightest and flattest plywood available and subjecting it to all sorts of manipulation, a couple of the flip-top sections are warped to there are slight gaps on one side.

I modified the plan so that the middle section could lift up as well. The back 1x3 of the storage section extended the full width.

Built from Plan(s)
Modern 2x2 Desk Base for Build Your Own Study Desk Plans
Sawhorse Storage Leg Desk
Estimated Cost
AUD$60 per desk
Estimated Time Investment
Week Long Project (20 Hours or More)
Finish Used
I experimented with a paint wash finish 50/50 paint/water for the inside of the storage sections. Everything was given a couple of coats of clear satin varnish.
Recommended Skill Level
Intermediate

Girl's Pink Play Vanity (modified from Mila Vanity Plan) Kids Toy

Submitted by kwildman on Sun, 12/08/2019 - 08:41

The cutest! Little girl's vanity built from pine and painted two tone blush pink. So adorable. 

Plans modified from the mila vanity plan.  I used a jig saw to cut out the mirror board backing from 3/4 plywood to mimic an antique vanity.  I purchased the laser wood frame from Michael's and attached with gorilla glue.  I used a plastic mirror material that could be cut to fit the frame.  Remember to spread your glue very thin on the back of the mirror material or it will mildly distort the reflection if it is not perfectly smooth.  

I added a vanity board in the knee space that I also cut with a jig saw from a 1x4 board.  I copied that pattern for the back of the stool.  I used Ana's kids art center stool plan for that. 

The crates are made using wood lathe scraps and a piece of 1x6 scrap.  

The paint on the vanity is Rustoleums chalked paint in Blush.  The laser cut wood frame, crates  and stool are Krylon spray paint in Blush Gloss.  

Blog Link
White House Wood Shop
Built from Plan(s)
Mila Play Vanity
Arts and Crafts Play Table
Kids Art Center Stools
Estimated Cost
80
Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
The paint on the vanity is Rustoleum Chalked in blush (lightly distressed) with clear paste wax to finish.

The crates, stool, and wood laser cut out mirror accent are Krylon Gloss Blush spray paint.
Recommended Skill Level
Intermediate

DIY Farmhouse Cabinet

Submitted by Anonymous (not verified) on Thu, 08/10/2023 - 15:53

The inspiration for this piece came from an Instagram post. We decided on our overall dimensions (36" tall, 18" deep and 60" long), then more or less guessed what the size of the pieces for the face frame would be. We recreated it as best we could and I think it came out incredible. It has soft close drawers on top and the hand-made sliding shelves are also soft close. The raised panels for the doors were made on a table saw. The doors have soft close hinges. The cabinet is made from maple plywood, oak plywood, yellow pine and poplar. The top is made of cypress and stained with Minwax "fruitwood" color and semi-gloss urethane. Next step is to make the shelves which will be 48" tall overall.

Dave Patterson

DIY Can Good Storage

The can good organizers I found on line were metal and didn't fit the exact opening I needed. I built my own for much less than the metal ones (which were $36 each!). With this plan, you can build up to four of the size I made for under $36. See how they just blend into the cabinet and look like they are built in it? Here is the process. Step one: Cut the sides and the ledges. Step two: Attach pieces to the walls of the unit. Step three: Set the lauan onto the ledgers. See? I told you it was easy! I drew up a sketch of the size I used for my 12" opening with a cabinet depth of 11.5" (if you have doors, it will be a depth of 10.5-10.75"). The height of my can good holders are 11". Again, the plan can be adjusted to any size space, but I think if you go past three cans wide, you may want to use something more sturdy than the lauan. Additionally, if you make the unit taller and add shelves, make certain the cans will fit thru the opening, don't just measure with the can in place on the shelf. Cut list for 1 can good holder: 2 - 11"tall x 11.5"deep walls (the melamine is 11.75" deep, I had to trim mine down) If your doors are on your cabinets, your cuts will probably be between 10.5" and 10.75" 6 - 1x2" 10.5" strips 2 - 10.5x10.75" lauan cut for the shelf If your doors are on your cabinets, your cuts will probably by between 9.75" and 10" I used 1.25" finish nails, but you can use screws if you prefer. Wood glue, wood filler, etc. Cut 6 equal size 1x2 strips. 2 per ledge, one for the back support. The size of the opening subtract the width of the melamine walls (.75x2=1.5"). My opening was 12" and then I subtracted the 1.5" (for walls). Nail the bottom 1x2 to the end of the upright 1x2 as shown above to create the front ledge.  Flip the ledge over and attach the ledge to the front (finished) edge of the melamine. Make sure the bottom ledge is flush with the front and the bottom of the wall. Measure down 5.5" (halfway point) from the top and mark the edge of the wall. Attach the top ledge to the wall keeping the front of the ledge flush with the side wall front edge.  Find your center point again (5.5") and measure up toward the top .75" to create a bit of a roll for the cans to come forward when you remove one. Do the same for the bottom. Measure .75 up from the bottom and mark. Attach the back supports at the marks you made in the last step. Attach second wall and screw or nail supports and ledges. Once all the 1x2s are in place and secure, the lauan pieces will fit in place and stay with the weight of the cans. You can add glue to secure them, your preference. Then touch up the nail holes and slide into place. I hope this gave you a helpful way to store your can goods. Let me know if you have any questions. Happy building! Karen :)

Blog Link
The Quaint Cottage
Estimated Cost
About $36 for 4 units
Estimated Time Investment
An Hour or Two (0-2 Hours)
Recommended Skill Level
Starter Project

Chelsea Twin Beds

Submitted by sraper2 on Mon, 01/13/2014 - 13:36

I built these beds last week for the little girls and we all love them so much! I was looking for something girly and this fit exactly what I was wanting. I took some pictures of the build and posted them on my blog. Thanks for the amazing plans!

Blog Link
DIY Big Girl Beds...Finally
Built from Plan(s)
Chelsea Twin Bed or Bottom Bunk
Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
Paint
Recommended Skill Level
Beginner

Triple Pedestal Table

Submitted by Lawwife on Wed, 04/06/2016 - 07:21

I built this table in about 2 weekends. The aprox cost including screws, stain, and glue was about $175. I stained it weathered gray from Rustoleum. My husband thinks it looks great. Now to order the end chairs!

Built from Plan(s)
Triple Pedestal Farmhouse Table
Estimated Cost
$175
Estimated Time Investment
Week Long Project (20 Hours or More)
Finish Used
Rustoleum Weathered Gray
Recommended Skill Level
Intermediate

Modern Farmhouse Bed

Submitted by itsmagic on Sat, 12/14/2019 - 15:32

Hi Ana,

We build the Modern Farmhouse Bed frame in Australia. I had to convert the plans to metric and change the width to Australian King size dimensions(who knew there were so many bed sizes). I also modified the plans to have a LED light strip in the top of the head board for reading. A fun project that everyone is impressed with. 

My wife and I lived in Tok for about a year, and love seeing the animals, and landscapes around Delta in your videos. 

Thanks for your hard work,
Jim & Kylie
Gold Coast 
Australia

Built from Plan(s)
Modern Farmhouse Bed Frame
Estimated Time Investment
Week Long Project (20 Hours or More)
Finish Used
"Coal" Stain, and Antique White
Recommended Skill Level
Beginner

Modern Cut Out Nightstands

After I built Ana's plan for the Low, Modern Cut Out Headboard, these two nightstands were the perfect compliment. I love the modern, clean look, and big drawer space. The inset design of the drawers make placing the faces on the drawer really tricky, so I would definitely place on the faces after you have installed the tracks and the rest of the drawers.

Blog Link
Modern Cut Out Night Stands
Built from Plan(s)
Modern Cutout Nightstand
Modern Platform Bed Frame with Chunky Legs
Low Modern Cutout Headboard
Estimated Cost
$200
Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
Water based stain and poly
Recommended Skill Level
Intermediate

Comments

Back