Community Brag Posts

I made a smaller version of Ana's trash can for outdoor use. I used scrap wood that I joined with the Kreg Jig but I think it would have been easier to buy the size she recommends (but this was free!) We are always walking our dogs and then stuck with bags of poop and no where to put them. They end up in a pile near our door (GROSS.) so I built this to 'house' the dog poop until trash day. It's enclosed so there's no odor when you walk past it, and it looks much better on our front porch than poop bags. I painted it to match our front door so it looks like it 'belongs' up there. Ahhh, much better.

Farmhouse bed!!!

My new garage shelves.  Not my first project, but I really liked the way they turned out.  Used 1/2" plywood at 16" width.   I attached the plywood with wood glue and 2" brad nails every 12 inches.  I used an impact driver to screw the 2x4 into the wall and to attach the vertical legs. Saved a lot of time and wrist fatigue.

Had to adjust the measurements to fit the space I had to use it in my tiny kitchen but it turned out pretty well.

I've looked around for a crib for my son who is very manly, and also has a baby doll. All I could find were pink or purple or floral cribs which led me to the Internet in search of Plans to build my own. I found your site and love the crib that you built for Olivia. This is our manly version that my son and I completed today. Thank you!

Really enjoyed this project, thanks for the great plans!

I used Ana's plan as a base.

I changed it from 8x8 to 8x12, made the 4x4x8's to 4x4x10' for a higher main platform and swing platform, and added a 12' long monkey bar set to the other side. Also, an 8' climbing wall and a plank walkway to accompany the two slides.

For the clubhouse, I used Hardiplank 4x8 sheets for the siding and an EZ-Framer kit for the structure itself.

The slides I purchased from Lowes, monkey bars from Amazon, and the swing frame braces from Amazon as well. The swing kits I got from ebay.

I love the C&B Big Sur dining tables and was excited to come across these plans. I tackled making a copy of the Big Sur dining table using Ana's plans as a starting point with some modifications and custom dimensions (4' x 4' x 31"). This was my first major woodworking project and I wanted it to be as nice and strong as possible so I tackled joining the rails of the frame to the legs with mortise and tenon joints. The main reason I did this was because I used 1 1/4 and 1 3/4 red oak for the entire table and I just wasn't convinced screws could handle the weight of the top on the frame. I also wanted to learn how to make those joints. I used my plunge router to cut both the mortises and the tenons and it worked out reasonably well. Now that I have a table saw I will be using that with a dado blade for tenons in the future. I sanded to 320 grit and finished with four coats of General Finishes Gel Stain in Java followed by four coats of Minwax spray on polyurethane. The last step was to apply paste wax using 0000 steel wool and then buff with a clean rag. I love the way this came out and am now planning on making a bar cabinet with wine bottle holders in the same style. The total cost of the table was on the higher end than I'm used to because the wood was pricey but it was still so much less than the C&B Big Sur price tag. I'm lucky that I have a hardwood lumber supplier just a few minutes down the road that does custom milling of 100's of different species.

I finally have order in my garage! I built a mobile lumber rack using plans from the Rogue Engineer. My husband and I knocked out this project one Sunday afternoon. It can store a huge load of lumber and best of all, it’s portable. We are very, very pleased with the final project! Storing all our lumber on the rack has freed up a great deal of space in our garage.

Thanks for the free plans made some modifications.  Sharing for all....Have the assembly line going as gifts to my Oklahoma University friends...Personally I am Oklahoma State University....but was a Wine-A -Dirondack among friends....

This is the cabin single bed. The bookcase/drawers and desk are almost done and will be posted soon. This was a great project, very easy and my son is so excited! Thanks again Ana :) We used a green milk paint with Federal Blue milk paint over it, distressed it and then used a brown glaze and polyacrylic.

Wanted to utilize my daughters small bedroom, and give her a custom bed without a huge price tag.

Supply list...required an additional 2x4
Used a bunkie board bought at local furniture store ($50) instead of slats for mattress.
Cleats that were 2x2 weren't wide enough to keep bunkie board in- it kept falling out. (standard is 38 " wide) so I replaced those with 2x3s. Decking on platform is very sturdy- maybe a bit overkill for a 40 lb kid.

Overall a quick project. My mom and I built it- Lowes did all cuts for us (no charge!) except the angled stairs- which mom did.

Turned out great- were were brand new to this- so struggled a bit as instructions are somewhat vague (where to drill holes- step by step process out of order) Drill all your pocket holes in all pieces prior to assembly. I would have sanded and stained prior to assembly too- doing in a tiny bedroom was tricky. Staining and sanding took the most time.

Overall alot of fun- ready to do next project. Thank-you for the inspiration!

I am so happy with my work.. It has turned out perfect. I love them.

We bought a vacation home that has such a small kitchen. I knew we needed more storage. So I checked out Ana's plans and made this bad boy based on the Simplest Armoire plans.

The home is in the mountain/lakes area of northern New Hampshire, so I wanted to bring the outside colors in. I used Valspar Cabin Red paint and the Valspar Antiquing glaze over the top after distressing it a bit.

My husband and my boys built it, painted it, and stained it in a weekend. Great father and sons project. I used the same black paint and stain that Shanty-2-chic used. I LOVE it.. now on to the benches.