Community Brag Posts

Rustic x end table build

First ever wood project. Under $200 in materials! Less than a weekend of work (for two people). Beautiful results!!!!! Built from plans on Ana-White.com The only change we made to the build was adding some additional support legs in the middle of the bed. 

We built a pair of these for our kids. Wanted to surprise them with a little shelf for each and it was really easy to do. Kids never saw them until it was all done since we bought the wood for this at the same time as we bought the wood for our own bed that we made.

Spray painted them using Krylon spray paint had more trouble locating appropriate paint (needed pink & purple seems most places didn't have this actually in stock!) than we had making the actual shelves. Took quite a few coats of paint though to get them looking nice.

Biggest complication that we actually had was finding the wood in suitable straight pieces. Ended up taking quite a while to select suitable pieces since most were bowed or warped to the point of being useless for our needs.

Final result though looks great and the kids absolutely love them. They are perfectly sized for water bottles and both kids had them in usage within mere minutes of them going up on the wall.

I recently found a photo of Pottery Barn Kids Box Train shelves. The have been discontinued, so I decided to build a set of my own. They were really easy! I was able to build 3 shelves from (2) 1 x 8's, (1) 1 x 4, and (1) 2 x 4. Plans, silhouette file, and printable image available in my blog post. 

I always have heaps of scrap wood so I decided to make some lanterns.

These lanterns are larger than the last lanterns I made.

They are huge and they make a great statement.

I used old rusty fencing wire for the handles.

I also added some alluminium sheet to the 'ceilling' of the lantern so that there is no risk of burning.

The only cost was for the candles.

Built from the Triple Pedestal Farmhouse Table plans. Had to size down the plans a little bit to fit into my dining room. Created three pedestal legs but only ended up using two on the final table. Took about 16 hours from start to finish. All of the wood is pine except for the top, which is Poplar. Made a couple of mistakes along the way but am very happy with the way everything turned out. Feel free to ask questions and I will do my best to answer them. Happy Building!

The legs of this table are made from douglas fir purchased at my local big box home improvement store.  The table top is made of hard maple that i purchased from a local mill.  I modified the dimensions from the original plan because i really liked the look of the 4x4 legs.  The douglas fir is relatively inexpensive material and because the legs for the most part unseen once you have chairs.  I chose hard maple because i have three kids under the age of 6 that can destroy anything in their path. So having a kitchen table that could double as a nuclear bomb shelter was high on my priority list.

I recommend you purchase your wood from a local mill.  There are few technical terms you will need to learn before heading over to purchase your wood stock.  For example, lumber mills sale their wood stock by the board foot (width x length x depth) and if you want a 1 inch thick board you will need to ask for 5/4 board (pronounced five quarters) Marc Spagnolia (aka: The Wood whisperer) has a great 5 minute video that gives you all the information you need to walk into a lumber yard with confidence and purchase what you need.  KEY POINT: make sure your boards are straight and square. If your boards are not straight and square, it will cause you problems down the stretch.  In order to achieve this you must joint and plain your boards.  Since I do not have a jointer or plainer, I asked the lumber mill if they could help me out and they were nice enough to do it for an extra $25 dollars.  Well worth it in my opinion.

I did purchase one tool for this job, a biscuit joiner.  A biscuit joiner makes small cuts in the sides of your boards.  Small wooden biscuits are inserted in these slots and help keep your boards level when you glue up your boards.  They do not add any strength to your glue joints, but will save you a lot of time sanding your table top perfectly flat. I won’t go into a lot of detail on how to glue your boards up.  There are lot of great YouTube videos that give pretty good advice on the glue-up of your table top.

After you get your table top glued up, it is time to sand.  KEY POINT: Sand by sight, not by feel.  Your table top may feel really smooth to the touch, but when you go to stain, small swirl marks can make your final product look lackluster.  Invest the time in sanding.  I suggest getting some hallogen lights and put at the end of your table.  These lights help you see those imperfections that need to be sanded out. Also, I recommend using an orbital sander.  Be sure not to put any downward pressure, let the sander do the work.  Putting downward pressure is so tempting, but ultimately causes deep gauges in your wood that take even longer to sand out.

So one thing that I did learn when doing this project was that hard maple is one of the toughest types of wood to stain.  The wood is a very dense with tight porosity. This is what makes hard maple extremely durable and pretty, but unfortunately very difficult to stain. Most stains leave the maple looking blotchy (dark and light color all over the boards).  It was really frustrating trying to figure out how to stain this type of wood.  I searched the entire internet looking for tips on staining hard maple with very little luck.  So if you’re interested in using this wood…here is my playbook that produced pretty good results.  First of all you should really avoid the pigment type stains.  These are your run of the mill stains you find at your big box store.  I also had terrible luck with gel stains as well.  The best way to stain maple I found was to use a dye stain.  Dye stains have the ability to penetrate into the tight grain structure of the hard maple and leave you with a pretty nice color.   I used general finishes “dark brown” dye stain with the following steps:

• Sand up to 120 grit, then take a shop vac ( I know it sounds crazy) and vacuum all the dust up from the top of your table.  The shop vac pulls all the dust out of the pores and allows for better penetration.  Then take a tac clothe and wipe down your table top.  I used Minwax sanding sealer 1 to 1 ratio of sanding sealer to denatured alcohol.  This helps prevent blotchiness.  Please note that I tried prestain conditioner, dewaxed shellac and a few other products, but got significantly better results with the sanding sealer…..
• After letting the sanding sealer dry for 2-3 hours, I then proceeded to make 4 passes over the table with 220 grit sandpaper with my orbital sander. I proceeded this sanding with the shop vac and tac clothe wipe down of the entire table top.   I also did a slight wipe down with a clothe towel and denatured alcohol.  This helped raise the grain slightly/open up the pores of the wood.
• Finally I took a spray bottle with my stain and sprayed over the entire table top putting a nice even coat of stain.  This really worked well as my table was 7 foot wide. I quickly and gently wiped the excess stain off the table.

The results were really great.  The dye stain makes the figure of the wood “pop” and the sanding sealer keeps the color relatively even across your top.

For the top coat, I started out putting minwax high gloss poly.  I put several coats of this poly on the table, sanding with 400 grit sandpaper in between coats.  I really like this product.  I recommend putting it in the Fridge for 4-6 hours before you start working with it.  It will give you more time before the product sets up.  My final 2 coats I used behlen’s rock hard urethan satin varnish.  This product was truly rock hard, but once you put it on it sets up really fast…then it takes a long time to completely set up.  You had better work pretty fast using this stuff.  I used a roller to roll on all of my poly applications then evened it out with a really good paint brush. I built up layers of poly starting out with high gloss first, then switching to satin.  If you start out with satin and apply lots of coats, it can give a plastic type appearance to your finish that I do not like.

After 3 days of letting my final coat dry, I rubbed out the finish by taking 4 (0000) steel wool and a product called mohawk wool lube paste.  The steel wool evens out the finish and gives it an even sheen throughout the entire table top (see pictures).  The wool lube keeps you from burning through the finish with your steel wool.  Head over to Jon Peters Art & Home and he has videos on how to do this.

Hopefully this post helps some people. Let me know if you have questions.

Used the grandy sliding door console plans but modified due to space. Shortened it to a 5 foot length. Wanted rustic feeling so did a custom stain using a golden pecan mixed with golden mahogany. Being mindful of cost and used pine with bead board on the back.  Super pleased with the result! Thanks for the ability to use your plans!

I built this play fort and swing set based on Ana's Playhouse design. Today is my daughter's 3rd birthday and it is a present to her.
She has helped me the whole way through the project. It was a lot of fun building it with her.

For more pictures on my project see
http://flic.kr/ps/2spv6t

The deck is 12' x 8' and it is 5' off the ground to the top of the deck. The tube slide comes off of a platform that is 3' x 4' and 7' high off the ground to the top of the platform. I got the slides, swing arm and swing legs off a set from someone selling and old set through craig's list. Everything else i built myself.

I made these side tables (two matching ones) last year but never posted the pictures.  I will soon have plans available as well.

I made these from select Pine which is more expensive than the normal No2 Whiteboards.

They were made to suit the height of one of our sofas and finished in  Minwax Ebony and Minwax Satin Poly.

The hinges were from www.directfrommexico.com

Thanks for the easy tutorial...Made that last night with my two oldest kids (7 and 9) and we love it! 

We needed some way to organize shoes, coats, book bags and the the things that need a home when you have 4 kids. I found the plans for the Braden entryway units and I loved them! I showed them to my husband who built them for me one Saturday afternoon. We decided to use piece of paneling for a wall on the back of the lockers and used MDF for the shoe bases since we wanted them to be sturdy. I painted them Valspars "Tidal Teal" and then technique glazed them with a black brown color. I LOVE THEM! They are colorful and fun and so functional. I love this site and have many other projects for my husband to build as long and I get to do the fun part, PAINTING!!

Made to save space from hickory in an L shape to wrap around a column near the kitchen. Upper wrapped in trim with the lower section trimmed with some left over trim from another project. Two hooks on each side on the upper part and one each on the lower side. I used clear satin polyurethane and rustic red spray paint for the upper trim.

We used library catalog handles that I found cheap on Amazon. We adjusted depth reducing 3 inches and did an routered edge wood overlay on top. I also had my husband router all 1x2 and 1x3 except short edges of 1x2's. My favorite project yet but it took a couple week so to finish between job and kids. I used honey stain and 3-5 coats of poly until I was happy. Thanks for the guidance and giving me a plan to work from.

Project for a friends 2 year old, seats will hold a 200 lb adult. NIce starter project, best part was watching the little ones sit at "their" table once it was done

This is the third farmhouse doll bed we have made and it is by far my favorite!

We used Carrington stain which dried in one hour to it's perfect color (just be sure to wipe down after a few minutes as it sets more quickly than the regular oil-based stains).  And I sewed the blanket out of a $5 throw I had purchased at WalMart (the same throw made two scarves also!).  The mattress was made from a foam mattress topper wrapped in fleece.  Since we had all the wood as scrap in our garage, this project cost us nothing!

We donated it to a local tricky tray and it was priced in the $200+ range!