Community Brag Posts

Bunk bed system. My daughter picked the colors. She loves it

We built this to the dimensions on the Farmhouse King plan we used Hardware from our old bed to attach the headboard and footboard to the siderails The finish was a coat of white paint sanded and then a coat of weathered grey stain and then additional sanding to weather it a bit

We used the plans for the Farmhouse Table Knockoff similar to the one from RH, to build this table. We made some changes, and some hints:

1. The table is made of Cedar, as it will be used outside. Pine is just not an outdoor-friendly material, but Cedar is rather insect-proof. This will be used at a beach house.

2. We used 1x, not 2x on the top. The top just seemed to clunky with the 2x size. Plus, it's near impossible to find 2x in cedar.

3. We couldn't find 8x1 or 8x2 for the breadboard, so we used 6x1 (same as the table top).

4. We measured the length of the breadboard before we cut. I"m glad my husband made that suggestion because I found the seven (7) 1x6's totaled 38 3/4, not 38 1/2 as the plans call for. So it really does depend on the wood and humidity and such. So I think it's a wise decision to measure the width of all of the boards before you cut that piece.

5. We did not screw into the table top as recommended by the plans.

I'm a novice- but these plans were so great that it came out beautifully! Definitely won't be my last project using plans from this site. Rogue Engineer rocks!

I made some modifications and cut this down to a 7ft long table. I also used thick plywood boards on the side but covered it up with a thin smooth looking plywood board for a nicer clean crisp look. 

Use poplar because it takes paint so well. Ended up using a preambled worktop for the top. Pocket screws and glue.

This was so easy and relatively quick. I think it took us an hour and a half. We had all wood precut at Home Depot at the time of purchase. There were a couple boards that weren't cut accurately, but I just went with it because I don't mind imperfection. And some boards were a bit curved. I think it just adds to the rustic, "reclaimed" look. I ended up using mostly pressure treated wood as it was cheaper. They also didn't have the lengths in the instructions so I had to buy more pieces which made the cost about $80. I only used nails to build this, not the screws mentioned in the supply list. I finished it with a quick slap job of white paint, leaving some wood exposed. Sanded some off before adding a steel wool/vinegar stain. I ordered a metal frame to attach to the headboard thinking they were all a standard size and would work with these plans. Beware, this is not the case. The frame is narrower than legs and could not be bolted to them. I ended up slipping a 1 x 4 x 10 piece of wood into the grooves at the bottom, screwing it into place. Then I bolted the frame to that.

Modified mini kitchen. Side door has a magnetic closure. When hutch is inside, it fits under the couch!

I saw the farmhouse table plans on the site and forwarded them to my father, who was quite interested in what I wanted to build. We decided the specs for the 72" tabletop in order to fit my dining room. What I didn't know was that my father, Charlie, had already located some pristine black walnut to construct the table and had already begun planing the wood for the table. My loving aunt and uncle "donated" the wood to me and my Aunt Mitch & dad planed all the wood themselves. As you will see, the planks that run along the top of the table are not the same size however the overall size if the tabletop is the same. Charlie fit everything together and made it work. He cut all the pieces and did all the work! Therefore, we have a beautiful, unique and absolutely STUNNING new table for our family!
Thanks to Ana White for this site, to my aunt & uncle for their resources and
time, to my husband who meticulously and gingerly applied the poly and finishing touches - and thanks especially to my loving father, Charlie, for all of his hard work, talent & generosity. We will now have a beautiful table to share years of memories & meals with one another!!

Used the inspiration of Ana-White dog kennel and made ours with an old bed frame that wasn't being used anymore. I'm very happy with how it turned out. I just need to paint and stain it. You can see the side is from the bed headboard and footboard.

This was a fun project, my first attempt at something like this. It took me several weeks of only working on it with whatever spare time I could find. Hopefully, it will serve my families home dining needs for years to come!

I really really wanted a farmhouse table...but...we had a space that needed a square table AND I needed to fit 8-12 people (or more!) so we modified Ana's farmhouse table plans to not only be square, but really big as well. This table is 6 ft on each side. Since the table itself was so big, we reversed the breadboard ends and used a 2x4 on 2 ends just to even out the size a bit since is not rectangular...and the area is quite small but needed a big table. I didnt want it to be completely out of proportion. We did not use a stretcher because of the square factor, but each leg is a 4x4 post and reinforced underneath. It's HEAVY. It won't be moved anytime soon! I'm loving it:)

We used Ana's tilt trash can plans and antique/distressed finishing tips. It came out great! We love it!! Thanks Ana!!!

This took me about an hour to build. I used two coats of paint and bought the cheapest laundry baskets that Walmart sells here in Alaska ($3.77 each). I added some felt to the bottom corners as it'll be sitting on a hardwood floor. Very happy with the finished product!