Community Brag Posts

Built this table using the Ana White plans everything worked great.

I used the idea of the Farmhouse Table and Coffee Table to build this table and benches. I used simple whitewood for the table because it's cheap. This table doesn't take long to build, only a few hours. But this time I used oil-based stain and had to swap out a few boards because they were warped so it took longer than expected.

Video of Build:

https://www.youtube.com/watch?v=yDwXPVC4m58

Build Instructions:

http://www.instructables.com/id/Mason-Bee-House/

Native mason bees can be housed to protect them from pests, diseases and predators. They are excellent early season pollinators for orchards and other early season fruit crops. Mason bees can do more work than non-native honey bees, even on a cloudy rainy day. Also, mason bees are solitary non-aggressive bees, which makes them ideal for folks with pets or children. The initial step for the care of mason bees is to build a nest block or mason bee house.

This was my first project and I had a ton of fun working on it. My grandpa has a professional wood shop, but as he has gotten older it hasn't been used as frequently. Most of my time was spent fixing broken equipment. I made a couple wrong cuts and had to go back to the store. All in all I love my new bed, I spent quality time with my grandpa, and it is a solid piece of furniture built for a fraction of what a bed should cost.

I'm just a novic so this was a challenge and lots of fun! I Made this one and just finished. I used oak plywood, oak lid, rocklar hinges, stained and poly coated ever thing about 3 times. Looks great!  Those hinges a expensive but work great.

Made this for our daughter's American Girl doll for Christmas. The mattress is a basic box pillow, made out of the cheapest bleached muslin from Joann, and stuffed with polyfill. I had to make a couple before I got it right. It needed to be a little longer and wider than the dimensions of the bed to fill the space all the way. It's been a while since I made them, but I'm pretty sure I cut the box corners at 2" and added an inch to the width and length of the actual bed measurements, plus a 1/2" seam allowance on each side. It makes for a feather bed look. The coverlet is 2 pieces of broadcloth sewn right sides together (leaving an opening to turn) and then turned right side out. Then I sewed trim in rows down the front. The blanket at the foot of the bed is furry minky fabric from Joann. It was really fun to build this bed and design the bedding. Thanks for the plans! My daughter loved this!

This was my first build, I never picked up a drill until now, but my mom really wanted something nice to hold her microwave but everywhere we looked for an island that would support it was just to flimsy so when I saw these plans and how cute it looked I told her I'm gonna build you this. I didn't add a drawer manly to force my family from putting junk in there that doesn't belong in a kitchen. I had a lot of fun building this and definitly learned a lot. Thanks for the plans.

This dog bed was built with furniture grade pine and stained in Minwax Golden Oak.  I added stairs and a storage drawer in the bottom.

This is an adaption of the shoe shrine shelves. Since I didn't have a closet or other room than the bedroom to put these, I put them on their side. I modeled these off the shoe shrine shelves.

Each cubby is 11 3/4 deep x 8 x8 for the long version. The 2nd version I made was only 48 inches wide and did not divide well so I simply left the center cubby wider. I also made the 48" version to have different height shelves for purses in the middle and flats on the bottom.

I basically flipped the shoe shrine's on their sides and added LED lights. This also inspired a tall version for a cubby we had upstairs.

I used a panel saw to cut the plywood and then assembled with a Kreg pocket hole jig for horizontal pieces and biscuits for the top and the dividers. I did not want to fill the holes or I would have used Kreg instead of the biscuits.

I used 3/4" paint grade plywood and a 1/4inch back panel.

LED lights came from LED wholesalers on amazon. This step requires electrical knowledge! Not much more than a wiring a light but do not attempt if you are not qualifed to do so. LED strings required a fine tip soldering iron, wire and heat shrink.

This project was a labor of love for sure.  It took me an hour here, an hour there over the course of several months before I finally finished it.  I have never felt so proud of something I built, and I truly could not have done it without the plans written up on this site!  Thank you so very much for the service you provide with your free plans!  

I started with rough-cut American walnut from a guy's basement.  It had been stored for over 50 years in a nice dry climate.  After planing it, running it through a jointer, and trimming off the crooked parts with my table saw, I was able to get everything to line up pretty well.   I will say the drawers sure gave me a run for my money!  Those are so difficult to get perfect! 

The stain I used is a Kona stain from Varathane.  I truly couldn't be more pleased with how it turned out.

After showing my wife the plans, she did not like that flat top so I did some drawings until she liked what I had. I Modified the plans so that we could get what we liked. I used all 2" lumber instead of 1" because I wanted it to be nice and heavy. Raised the base of the side rails by 3" so that there would be more ground clearance, and used plywood under the slats so that we didnt need to use a box spring. I think it came out well.

I started with the Camp style loft bed, and modified it. Since we had a full sized bed, we knew that we needed it to be wider. Also, we knew we wanted a slide, since baby girl LOVES slides. We found one on CraigsList that was too long, but we cut it down and found a way to attach it. We also aren't very good carpenters (yet), so we had some issues with our stairs being wider then our platform, and had to add an extra piece. Overall, this project took us 3 weekends and a few nights after work. Also, we were using the plans which suggested it would only cost around $50, wasn't quite the case with us...I am pretty sure we spent over $200, but we didn't really have paint, sandpaper, the slide, etc. So that is pretty all-encompassing. Very happy with our results, and We cannot wait for the baby girl to see the outcome!

With another baby on the way in a few months, we decided to move our 2+ year old daughter across the hall into her first big girl room. I built big sister the Kendal Extra Wide Dresser, Traditional Wood Toddler Bed, Letter A Shelf and a Dollhouse Bookcase and matched the colors with her new comforter, lamps and princess canopy tent from the Land of Nod outlet.

A lot of people have done some pretty cool modifications to this project, but at the end of the day, we decided to follow the plan verbatim and build the Pottery Barn design. This build was super easy. Probably spent most of the project time sanding over and over in order to ensure that it was splinter-free, smooth, and safe for our princess. I do note that the side rails in the project design are somewhat low after you put the mattress down. However, this was really only a concern during the first few weeks. Although our daughter somehow was able fall to the floor during the first night (without incident--she did not even wake up--thank god for carpet), after she became accustomed to the bed, the lower side rails actually work rather well. Our daughter, a insanely crazy sleeper, usually wedges herself against the side rails at different parts of the night. She might hang a limb or two over the rails, but never through the rails, and she never falls off the bed.