Community Brag Posts

These were made from scrapwood.

The table and bench project were awesome. I got a lot of inspiration from these, and have built 4 table so far. After posting the first one on Facebook, everyone wanted one. The one thing I would recommend is to really pay close attention to the lumber you're buying, make sure it straight and the edges are not chipped, to ensure all yourights seams match up, and your project ends up square.  A tip to alleviate all this,  is to buy everything wider than you need, and rip it straight through your table saw. What I mean is, if the table top calls for 2x10's, then buy 2x12's instead, and rip them down to 10 inches, so you're seams match up perfectly.  It may cost a tad bit more, but you will definitely be happier with the end result. 

Needed cabinet for trash and recycling, so modified the plans to fit under the existing counter top.

I build the bar table with an x-base and created some stools using part of the plan. We really wanted backs on the stools so I made them up!

This was made from scrap wood, a cheap $5.00 mirror and some hooks. This hangs near my front door and I hang scarves and bags on it. Always good to have a mirror to double check yourself before you leave the house. It was based on Ana White's Craftsman Frame.

Capped railing and head/foot board for a different look. Did not like the look of the carriage bolts so sunk those in and used buttons to cover. Modified slope and added hooks to ladder so we could remove to vacuum etc. Would of added one more step if I were to do it again. My guys are little so added railings to back side top and bottom and extended railings.

This is my very first project. Never used a saw before until a few weeks ago. I am really happy with the way it turned out.

I shortened the plan and modified the second shelf. I was planning on an "X" brace for both sides but got carried away and realized it wasn't going to work on the one side. I like the end result and don't mind that its missing.

I would have finished it sooner but was a bit intimidated by the angled cuts. My miter saw only cuts 45.

I built this Counter for a new business in Chatham, Va. Will add lighting in side !

Had to trim a little off the barn door track so they would fit, but overall, great project!

Loved this project. Modified it slightly with a side mounted roll away laybox. Also I made my own dual linked chick lifts system.

Solid garden lounger and side table to match our garden chairs and table.

I followed the plan, and used plain pine wood.  The wood cost $106 at my local Home Depot.  The Kreg R3 Jr. Jig, Clamp and Screws I already had from a previous project. This is a weekend project.  Biggest obstacle here is to make sure the shelves stay level.  After it was built I sanded everything with 180 grit before going to the staining step.

Stain...  I made a pot of STRONG Tetly Black Tea and painted the entire table.  I decided to go with this Oxidizing Stain (http://www.sweetpickinsfurniture.com/2011/01/how-to-weather-new-wood.ht…) for the wood.  The Black Tea increases the tannins in the wood, which makes a stronger reaction in the woodgrain after you apply the oxidizing solution.  After the solution dried I sanded lightly with 180 grit again and now it's ready for Wipe-On Poly to be applied.

Just one small hint.. The Oxidizing Solution takes a few days to react, so plan accordingly.  I let mine set for 7 days before use.

Thank you for helping our family stay organized and keeping our entryway clean.

Used the cedar concept from a grilling station project to create a wine wall from cedar fencing. - Chris K

Here is the Easy Kitchen Island all finished. I learned to use my k-reg with this project. To attach the top I instead used corner blocks in each corner of the bottom unit and screwed the top in place. I found this made the piece more sturdy. for the 1x2's I used furring strips which are not very nice however I painstakingly picked through a large pile till I found ones that were straight and without knots. I then had to sand them like crazy. Saved a ton of money but worked very hard. This project actually took 19 - 1x2's rather than what the plan called for. When complete this piece was very heavy...I love it and have found the perfect home for it.
Thanks again Ana!
Janet

Rustic tv stand made from pallets and reclaimed ship lap and 2x4's

I used cedar, stainless steel rails and finished with marine spar varnish.  Gave to my son for Christmas to hold his smoker/barbeque!   Thanks for the super project idea!