Community Brag Posts

This was a very simple pot rack and spice shelf using 1x3 for the pot rack and 1x4 for the spice shelf.

Spice Shelf is 7ft and the most complicate part was cutting the uprights for the large baseboards in our house. I used a profile gauge but this wasn't quite enough. Eventually I did some sanding on the spot to get the best fit. Having gained my addiction from Ana for Kreg Jigs the shelves and mounting pieces were added with pocket hole screws. By placing the screws on top or on the bottom I was able to avoid the necessity of plugging holes. Shelf spacing is completely custom for our needs and the large bottom portion will receive a cross brace in the front to hold in our shopping bags. Butterfly bolts were used to mount the shelving through the lathe and plaster walls.

The pot rack is simply a 1x3 ladder where I used a 1x3 for the spacing between the rungs. Large bottom to hold pot lids. Hooks were hand bent using a jig to ensure they were all the same. Mounted to the old brick chimney in the kitchen using TapCons.

Both items were finished in MinWax Mahogany and had one coat of of poly to keep the rustic feel.

Length of project depends on drying times.

Any questions please let me know!

I just finished my first project with upholstery!  I built a bench following Ana's plans from a couple of 2x4s and used this gorgeous fabric from Minted.  Minted is November's sponsor for the Fab Furniture Flippin Contest.  The paint color is Behr's Island Aqua.  I used 3" thick upholstery foam (and WOW that stuff is super expensive).  I love diamond tufting and followed a tutorial from Addicted 2 Decorating.  

The bench is super compfy.  I love it and I love the bright cheery colors.  

Made it a little taller and a little deeper.  

The husband kept complaining that the washer and dryer were too low without pedestals. Well, no problem! I've got plans from Ana's site.

I measured to fit our machines and followed the plans. But somewhere along the way I screwed up. I think it might have been how I attached the legs with the "L" brackets. My legs were sitting away from the base, not flush with it. Anyhow, the way to correct my mistake was to attach the moulding along the sides, front and back of the base, not around the legs. But I don't mind the way it looks. Just an FYI: there was a lot of waste with the sheets of MDF, but that's not a problem because I'm using it in another project as I write. :)

First, I put on two coats of primer. Then I decided I wanted a splash of turquoise in the basement, so I mixed a blue and yellow paint until I got the color I desired. After a few coats of paint, I distressed and then decided to tone down the color a bit with a Valspar glaze. I put on two coats of poly, hoping that would be enough to withstand the inevitable water on the pedestal. I thought the piece was screaming for a quote, so I painted "The most memorable days usually end with the dirtiest clothes."

And you think with the new height he'd help me with laundry a bit more? Yeah, I think not.

Our original sofa and loveseat turned out so well that my parents asked that we build them a set. It was our first time converting the plan to a single seat so I was nervous on how it would turn out, but it looks great!

This TV console was made on request.  Its made from maple plywood and Pine top, trimmed with Small crown,  large chair rail  and base board moulding.  It has one media shelf a larger shelf for Pictures. The very bottom has two 18 inch drawers that are 5 1/4 inches deep for dvds or games.

Followed the plan, adjusted the height to accomadate a trundle bed in the future. Tapered the edges of the 2x6 material for a shaker/craftsman look. If you cut the board at a 25 degree angle the 2x6 material will rest right in line with the 2 x 4 material below. Be sure and add 2 to 2 1/2 inches to accommodate the taper edging.

Used Minwax gunstock stain to match the furniture and three coats of fast drying gloss poly.

I seen the plans for a coffee table made out of pallets submitted by Aud builder and just had to try it. The company where I work has tons of pallets so it really didn't cost me anything. I added an additional pallet and left the casters off. In place of the casters I put 4, 4" 4x4's at the corners and then used 1x4 at each of the corners to connect the whole thing. Then I did the white wash on it. I loved the color and had a lot of fun putting it together.

I worked on this over the past couple of months (would have been quicker, but you know..life gets crazy sometimes!!)

I used the farmhouse table plans to a tee and then stained and poly'd it. It turned out great!!! My Wife loves it and now all I have to do is build the benches. The wood is cut for them, just need to find the time to do it. This is my 4th Anna-White project. I have also built a bench for the end of our bed, some laundry cubbues, and a day bed.

I love this site and plan on using much more...I have friends and family wanting me to build them stuff...the only thing now...is how much do I charge..... :)

I pretty much followed the original plans.  I added a chamfer on the outside corners of the posts and on the top boards on the head and foot boards.  I also stained these to match the nightstands.  Since I used a foam mattress, i built a platform by gluing/screwing a 2x4 inside the side rails.  Then I set 1x6s on the 2x4 to support the mattress.  

I use the free version of Sketchup to design the bed and estimate materials needed.  

Lessons learned

• Take extra time to figure out how to connect the side rails to the head and foot boards.  I thought i could use a sliding lock but this wouldn't work for my design.  I improvised using 3x7 tie plates and screwed the two components together.  For the headboard, I lined the 2x4 with the inside headboard post.  For the footboard, I bent the tie plate 90 degrees and screwed the 2x4 to the footboard.  It worked very well.
• I would recommend chamfering the outside top of the side rails.  I didn't and my wife complains that she  bumps her shins on it. 
• Top boards are 1x5s, which in my are are only sold at home depot.  The other wood is readily available.

It's not that difficult of a project.  It is time consuming, though.

I've taken quite a bit of time building this project. My goal was to use all material we had here so, I had to cut down 2x4's and 1x6 tongue and groove. I am proud of how this turned out, now to build it's match.

I started with Michaela's Kitchen Island plan, but reduced the dimensions and material sizes. I used 2x2s for the legs and 1x3s for the rest of the project. Everything was kreg jigged together. This project would've taken less time but the drying time for the stains ate up work time! :)

I built these out of necessity to keep my tipsy Christmas decorations from blowing over. The last couple years I spent a lot of time picking these trees up off the ground. I like how they turned out and were relatively easy to build.

I was excited I got to use my Kreg Jig for the first time, which looked more difficult to use than it actually was. Although these are cedar planters I used all pine from big box orange. Some leftover from the farmhouse queen bed I built and the rest I purchased.

The finish didn't turn out as grey as I would have hoped using the steel wool and vinegar, but I still like the aged look. I added the "x" detail in the front afterward and instead of staining my wife thought it looked better natural. Either way I would have been happy. I will be able to use these year round in some capacity.

My son saw this project and wanted a rocketship.  I was also tired of piling up his books on the floor.  The only wood I bought for it was 1/4" ply for the back as I used leftover 3/4" plywood for the bookcase itself.  Fairly easy with a Kreg, it just took a little while to finish all of the painting.

Made by my husband.

This is a 4 x 6 sand box. I took the Idea from this website and add a roof just for looks. It is made with 2 x 12 , 1 x 4 and 2 x 4. I used Flood Stain which I loved the clean up. I made the second one with 2x12 and 2 x 4 because it was going on a comminuty playground and I thought it sould be stonger. It takes 22 50 pound bags of play sand to fill it. Had a great time building them Thanks for the idea

The plans are pefect. Very easy to follow and the measurements make the drawer install a breeze. Very enjoyable project.